Hostname: page-component-cb9f654ff-hqlzj Total loading time: 0 Render date: 2025-09-05T02:14:13.448Z Has data issue: false hasContentIssue false
  • English
  • Français

Jet-printed Fabrication of a-Si:H Thin-film Transistors and Arrays

Published online by Cambridge University Press:  17 March 2011

W.S. Wong ,
S. Ready ,
R. Matusiak ,
S.D. White ,
J.-P. Lu ,
R. Lau ,
J. Ho  and
R.A. Street
W.S. Wong
Affiliation:
Electronic Materials Lab
S. Ready
Affiliation:
Electronic Materials Lab
R. Matusiak
Affiliation:
Document Hardware Lab 3333 Coyote Hill Road Palo Alto, CA 94304, U.S.A
S.D. White
Affiliation:
Document Hardware Lab 3333 Coyote Hill Road Palo Alto, CA 94304, U.S.A
J.-P. Lu
Affiliation:
Electronic Materials Lab
R. Lau
Affiliation:
Electronic Materials Lab
J. Ho
Affiliation:
Electronic Materials Lab
R.A. Street
Affiliation:
XEROX Palo Alto Research Center
Get access

Abstract

Phase-change wax-based printed masks were used to fabricate a-Si:H thin-film transistors (TFTs) in place of conventional lithography. Wax-mask features with a minimum feature size of ∼20 [.proportional]m was achieved using an acoustic-ink-printing process. Bottom-gate TFTs with source-drain contacts overlapping the channel were created using a four-mask process. The TFTs have I-V characteristics comparable to photolithographically patterned devices, with mobility of 0.6-1 cm2/V·s, threshold voltage of 2-3 V, and on/off ratios exceeding 107, for devices with channel lengths below 50[.proportional]m.

Information

Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 664: Symposium A – Amorphous and Heterogeneous Silicon-Based Films-2001 , 2001 , A17.4
Copyright
Copyright © Materials Research Society 2001

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

Article purchase

Temporarily unavailable

References

REFERENCES

1. Sanada, M., Nakano, K., and Matsunaga, M., Jpn. J. Appl. Phys. Part 2 37, L1448 (1998).Google Scholar
2. Garnier, F., Hajlaoui, R., Yassar, A., and Srivastava, P., Science 265, 1684 (1994).Google Scholar
3. Bao, A., Feng, Y., Dodabalapur, A., Raju, V.R., and Lovinger, A.J., Chem. Mater. 9, 1299 (1997).10.1021/cm9701163Google Scholar
4. Chang, S.-C., Bharathan, J., and Yang, Y., Helgeson, R., Wudl, F., Ramey, M.B. and Reynolds, J.R., Appl. Phys. Lett. 73, 2561 (1998).Google Scholar
5. Perçin, G., Lundgren, T.S., and Khuri, B.T.-Yakub, Appl. Phys. Lett. 73, 2375 (1998).10.1063/1.122465Google Scholar
6. Ma, E.Y. and Wagner, S., Mat. Res. Soc. Proc. 507, 13 (1998).10.1557/PROC-507-13Google Scholar
7. Gleskova, H., Wagner, S., and Shen, D.S., J. Non-Cryst. Solids 227–230, 1217 (1998).10.1016/S0022-3093(98)00308-1Google Scholar
8. Gleskova, H., Könenkamp, R., Wagner, S., and Shen, D., Electron Device Lett. 17, 264 (1996).Google Scholar
9. Hayes, D.J., Cox, W.R., and Grove, M.E., J. Electron. Manuf. 8, 209 (1998).Google Scholar
10. Elrod, S.A., Hadimioglu, B., Khuri-Yakub, B.T., Rawson, E.G., Richley, E., Quate, C.F., Mansour, N.N., and Lundgren, T.S., J. Appl. Phys. 65, 3441 (1989).10.1063/1.342663Google Scholar