Hostname: page-component-8448b6f56d-t5pn6 Total loading time: 0 Render date: 2024-04-25T02:19:41.285Z Has data issue: false hasContentIssue false
  • English
  • Français

Microfrictional Properties of Titanium Carbide

Published online by Cambridge University Press:  01 February 2011

Syed Imad-Uddin Ahmed ,
Giuseppe Bregliozzi  and
Henry Haefke
Syed Imad-Uddin Ahmed
Affiliation:
Micro and Nanomaterials Section CSEM Swiss Center for Electronics and Microtechnology, Inc. CH-2007 Neuchâtel, Switzerland
Giuseppe Bregliozzi
Affiliation:
Micro and Nanomaterials Section CSEM Swiss Center for Electronics and Microtechnology, Inc. CH-2007 Neuchâtel, Switzerland
Henry Haefke
Affiliation:
Micro and Nanomaterials Section CSEM Swiss Center for Electronics and Microtechnology, Inc. CH-2007 Neuchâtel, Switzerland
Get access

Abstract

The tribological issues associated with silicon-based microelectromechanical systems (MEMS) are well known. A popular solution to improve the tribological behavior is to apply different kinds of thin films. One film material, shown to have favorable properties in specialty applications, and which may also be suited for MEMS, is titanium carbide (TiC).

This paper examines the microfrictional properties of titanium carbide surfaces with two surface roughnesses sliding against polished 2 mm diameter TiC counterbodies. A comparison of the microfrictional behavior is made with various other surfaces sliding against the same material. Results indicate that the microfriction of smooth TiC sliding against a smooth TiC surface is low and similar to silicon or TiC sliding against a hydrophobic self-assembled monolayer. However, friction increases when the polished TiC ball slides against a rough TiC surface. Experiments at various relative humidities show that friction increases with increase in the relative humidity for two smooth TiC surfaces sliding against one another, but is reduced at higher relative humidity if the surface of one of the sliding partners is considerably rough.

This microfrictional study shows that TiC is well suited for microtribological applications. However, for optimal performance, the surface characteristics need to be tailored to the operating conditions.

Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 782: Symposium A – Micro- and Nanosystems , 2003 , A8.6
Copyright
Copyright © Materials Research Society 2004

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1. de Boer, M.P. and Mayer, T.M., MRS Bull. 26, 302 (2001).Google Scholar
2. Gardos, M.N., in: Tribology Issues and Opportunities in MEMS, ed. Bhushan, B. (Kluwer Academic, Dordrecht, 1997) p. 341.Google Scholar
3. Gardos, M.N., Surf. Coat. Technol. 113, 183 (1999).Google Scholar
4. Sullivan, J.P., Friedmann, T.A., de Boer, M.P., LaVan, D.A., Hohlfelder, R.J., Ashby, C.I.H., Dugger, M.T., Mitchell, M., Dunn, R.G., and Magerkurth, A.J., Mat. Res. Soc. Symp. Proc., 657, EE7.1.1 (2001)Google Scholar
5. Scherge, M. and Gorb, S.N., Biological Micro- and Nanotribology (Springer-Verlag, Berlin, 2001).Google Scholar
6. Maboudian, R., Surf. Sci. Rep. 30, 207 (1998).Google Scholar
7. Liu, H., Ahmed, S.I.-U., and Scherge, M., Thin Solid Films 381, 135 (2001).Google Scholar
8. Ren, S., Yang, S., Zhao, Y., Zhou, J., Xu, T., and Liu, W., Tribol. Lett. 13, 233 (2002)Google Scholar
9. Hild, W., Hungenbach, G., Ahmed, S.I.-U., Scherge, M., and Schaefer, J.A. (submitted).Google Scholar
10. Rye, R.R., Nelson, G.C., and Dugger, M.T., Langmuir 13, 2965 (1997).Google Scholar
11. Rajan, N., Zorman, C.A., Mehregany, M., DeAnna, R., and Harvey, R.J., Surf. Coat. Technol. 108–109, 391 (1998).Google Scholar
12. Ahmed, S.I.-U, Bregliozzi, G., and Haefke, H., Wear 254, 1076 (2003).Google Scholar
13. Radhakrishnan, G., Adams, P.M., Robertson, R., and Cole, R., Tribol. Lett. 8, 133 (2000).Google Scholar
14. Boving, H.J. and Hintermann, H.E., Thin Solid Films 153, 253 (1987).Google Scholar
15. Boving, H.J., Hintermann, H.E., and Stehle, G., Lubr. Engin. 39, 209 (1983).Google Scholar
16. Lee, S., El-bjeirami, O., Perry, S.S., Didziulis, S.V., Frantz, P., and Radhakrishnan, G., J. Vac. Sci. Technol. B 18, 69 (2000).Google Scholar
17. Ahmed, S.I.-U., Bregliozzi, G., and Haefke, H., (in preparation).Google Scholar
18. Meine, K., Schneider, T., Spaltmann, D., and Santner, E., Wear 253, 725 (2002).Google Scholar
19. Kogut, L. and Etsion, I., Tribol. Trans. 46, 383 (2003).Google Scholar
20. Ando, Y., Wear 238, 12 (2000).Google Scholar