Hostname: page-component-8448b6f56d-sxzjt Total loading time: 0 Render date: 2024-04-20T01:54:15.921Z Has data issue: false hasContentIssue false
  • English
  • Français

Preparation of Cross Sectional TEM Samples Using Lithographic Techniques and Reactive Ion Etching

Published online by Cambridge University Press:  16 February 2011

Jeffrey T. Wetzel  and
K. L. Kavanagh
Jeffrey T. Wetzel
Affiliation:
IBM Research Division, T.J. Watson Research Center, Box 218, Yorktown Heights, N.Y. 10598 Advanced Products Research and Development Laboratory, Motorola, Inc, 3501 Ed Bluestein Blvd., Austin, TX, 78721
K. L. Kavanagh
Affiliation:
IBM Research Division, T.J. Watson Research Center, Box 218, Yorktown Heights, N.Y. 10598 Department of Electrical and Computer Engineering, UCSD, San Diego, CA 92093
Get access

Abstract

This paper summarizes methods used to create cross-sectional samples for transmission electron microscopy and introduces another variant of the technique all of which rely upon some combination of lithographic patterning and reactive ion etching. The basic idea pursued in using these techniques was to form, from a preselected location, samples that had a large transparent area without use of mechanical polishing or ion milling. Samples were successfully prepared in this manner, but room for improvement remains due to the limited range of diffraction conditions available for imaging or diffraction pattern formation.

Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 199: Symposium W – Specimen Preparation for Transmission Electron Microscopy of Materials II , 1990 , 43
Copyright
Copyright © Materials Research Society 1990

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1. Kelly, T.F., in Workshop on Specimen Preparation for Transmission Electron Microscopy of Materials II, see earlier this volume, edited by Anderson, R.M. Google Scholar
2. Alani, R. and Swann, P.R., in Workshop on Specimen Preparation for Transmission Electron Microscopy of Materials II, see earlier this volume, edited by Anderson, R.M. Google Scholar
3. Sweeney, J., J. Vac. Sci. and Tech. B3, 918 (1985)Google Scholar
4. Dobisz, E.A., Craighead, H.G., Beebe, E.D., and Levkoff, J., J.Vac. Sci. and Tech. B4, 850 (1986)Google Scholar
5. Wetzel, J.T. and Danner, D.A., in Workshop on Specimen Preparation for Transmission Electron Microscopy of Materials I, edited by Bravman, J.C., Anderson, R.M. and McDonald, M.L. (Mater. Res. Soc. Proc., 114, 253 (1988)Google Scholar
6. Wetzel, J.T., J Electron. Microsc. Tech., 11, 62 (1989)Google Scholar
7. Wetzel, J.T., Jost, M., Rishton, S.A., Fryer, P.M., Kwietniak, K.T., Klaus, D., Bucchignano, J.J., Hu, C.-K. and Brown, T.J. Jr., Ultramicroscopy, 29, 110 (1989)Google Scholar
8. Cargill, G.S., III Angilello, J. and Kavanagh, K.L., Phys. Rev. Left. 61, 1748 (1988)Google Scholar
9. Rishton, S.A., Schmid, H., Kern, D.P., Luhn, H.E., Chang, T.H.P., Sai-Halasz, G.A., Wordeman, M.R., Ganin, E., and Polcari, M.R., J. Vac. Sci. and Tech. B6, 140 (1988)Google Scholar
10. Webb, R.A. (private communication)Google Scholar