Hostname: page-component-76fb5796d-qxdb6 Total loading time: 0 Render date: 2024-04-26T18:23:55.039Z Has data issue: false hasContentIssue false
  • English
  • Français

Towards an improvement of performance of TiAlN hard coatings using metal interlayers

Published online by Cambridge University Press:  11 February 2011

J. M. Castanho  and
M. T. Vieira
J. M. Castanho
Affiliation:
ICEMS – Grupo de Materiais e Engenharia de Superfícies, Departamento de Engenharia Mecânica, Universidade de Coimbra, 3030 Coimbra, PORTUGAL
M. T. Vieira
Affiliation:
ICEMS – Grupo de Materiais e Engenharia de Superfícies, Departamento de Engenharia Mecânica, Universidade de Coimbra, 3030 Coimbra, PORTUGAL
Get access

Abstract

TiAlN sputtered coatings have been used with success in high-speed cutting tools in the last few years. However, the adhesive failures of the coatings refrain its application in more severe wear conditions like as high-speed machining. The assumptions for the present research were based on the hypothesis that thin metal interlayers will behave as shear stress sinkers, which could decrease the delamination of the thin films. In the present work, coatings of TiAlN with thin ductile metallic interlayers (Al, Ti, Cu and Ag) were deposited by reactive d.c. magnetron sputtering. Multilayer coatings with aluminum, titanium and silver interlayers achieve higher adhesion values (70N) than TiAlN monolithic coating (40N). Three and five metal ductile layers contribute to an increase of hardness and Young's modulus without change the residual stresses of the monolithic coating. Contrarily, the introduction of copper layers reduces all the studied mechanical properties of the TiAlN monolithic coatings, which are related to the different deformation mechanisms of the ductile interlayers.

Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 750: Symposium Y – Surface Engineering 2002–Synthesis, Characterization and Applications , 2002 , Y5.18
Copyright
Copyright © Materials Research Society 2003

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1. Ma, K. J., Bloyce, A., and Bell, T., Surface and Coatings Technology, 76–77 (1995) 297–302 Google Scholar
2. Tavares, C. J., Rebouta, L., Andritschky, M., and Ramos, S., Journal of Materials Processing technology, 92–93 (1999) 177–183 Google Scholar
3. Tixier, S., Böni, P., and Van Swygenhoven, H., Thin Solid Films, 342 (1999) 188–193 Google Scholar
4. Subramanian, C. and Strafford, K. N., Wear, 165 (1993) 85–95 Google Scholar
5. Knotek, O., Löffler, F., and Kramer, G., Int. J. of Refractory Metals and Hard Materials, 14 (1996) 195–202 Google Scholar
6. Gao, H., Chiu, C. H. and Lee, J., Int. J. Solids Structures 29 (1992) 2471–2492 Google Scholar
7. Stoney, G. G., Proc. R. Soc. London, A82 (1909) 172 Google Scholar
8. Ward, L. P., Strafford, K. N., Subramanian, C. and Wilks, T. P., Journal of Materials Processing Technology, 56 (1996) 375–384 Google Scholar
9. Jiménez, C., Sanchéz-Fernández, C., Morant, C., Martínez-Duart, J. M., Fernández, M. and Sánchez-Olías, J., J. Mater. Res., Vol. 14, No. 7, Jul 1999, 2830–2837 Google Scholar
10. Jarms, C., Stock, H.-R. and Mayr, P., Surface and Coatings Technology, 108–109 (1998) 206–210 Google Scholar
11. Musil, J., Hrubý, H., Thin Solid Films, 365 (2000) 104–109 Google Scholar