Introduction
The present authors have presented two previous papers concerned with the mechanical properties of pure ice (Reference Glen, Jones and ŌuraGlen and Jones, 1967; Reference Jones and GlenJones and Glen, 1968). This third paper presents further results and also summarizes the earlier results in order to present a complete account of the work done at the University of Birmingham between 1964 and 1967. The work that was done on impure ice has been separately reported (Reference Jones and GlenJones and Glen, 1969) and is not mentioned here.
The object of the experiments was to investigate the mechanical properties of ice single crystals at temperatures lower than had previously been attempted. A number of workers have conducted investigations close to the melting point, and two groups, Reference Readey and KingeryReadey and Kingery (1964) and Reference HigashiHigashi and others (1965), have made studies at various temperatures down to −42°C. The present work includes results at temperatures down to −90°C.
Tensile Creep Tests
The method of growth of the crystals and a description of the tensile creep apparatus have been given by Reference Glen, Jones and ŌuraGlen and Jones (1967).
The glide direction
All the results pertinent to this question were presented by Reference Glen, Jones and ŌuraGlen and Jones (1967). The conclusion reached then was that 〈1120〉 is the glide direction in ice, a result which confirms the X-ray topographical work of Reference Hayes and WebbHayes and Webb (1965).
Analysis of creep curves
Creep curves obtained at −50°C are shown in Figure 1, in which the shear strain resolved on the basal plane, as defined by Reference Schmid and BoasSchmid and Boas (1950, p. 58), is plotted as a function of time. It is of the same form as that found at higher temperatures; a continually increasing creep rate is observed with no apparent strain hardening. The shape of the curves was found by plotting the logarithm of the strain a against the Iogarithm of the time t as is done in Figure 2. In all cases the result was a straight line showing that
Creep curves of ice single crystals deformed under various stresses at 50°C.
Creep curves of Figure 1 plotted logarithmically.
where m = 1.5±0.2 for shear strains between 0.3 and 4%. Below 0.3% measurements of the strain were unreliable. Above 4% the apparent value of m increased, possibly due to increased stress in the deformed region of the crystal, and for one crystal m equalled 2.2 between shear strains of 10 and 30%
Since ϵ ∝ t
1.5, it follows that 
and hence 
This being so, 
should be a constant for each crystal, the value of which depends on the resolved shear stress acting on the crystal. This was found to be so and since it was expected that the dependence of strain-rate on stress would be a power-law type relationship, a graph of log 
against log τ was plotted as shown in Figure 3. A straight line was fitted to these data by the method of least squares and is drawn on Figure 3. The equation for this line is
The stress dependence of the strain-rate of the crystals deformed at −50°C.
with n = 2.2+0.3 and τ 0 = 1930 bar s1/2.2. However, it is possible that the data would be fitted better by a non-linear curve, and to test for this, a least-squares determination of the constants in the simple parabolic type of equation
was made with the help of the University of Birmingham Computer Services’ KDF9 computer. Once this had been done, the Gauss criterion, as defined by Reference Worthing and GeffnerWorthing and Geffner (1943, p. 260) was used to determine whether the linear or non-linear function was the better fit to the experimental data. For the data obtained at −50°C (Fig. 3), the non-linear law, which is also drawn on the figure, proved to give a better fit. It is possible that the data are still better fitted with another non-linear equation, for example a circle or cubic parabola, but these were not tested since the object was primarily to show whether or not the data were randomly distributed about a straight line. Since now the slope of the curve is a function of stress, this means that in the power-law expression (Equation (2) above) n varies with stress from 1.0 at τ = 1.6 bar to 4.1 at τ = 6.2 bar. The value of n reported at Sapporo (Reference Glen, Jones and ŌuraGlen and Jones, 1967) of 4±1 is the value obtained at the higher stresses only.
All data obtained from creep tensile tests at −60°C were reported by Reference Jones and GlenJones and Glen (1968) and so will not be repeated here. The −60°C creep curves were analysed in an identical manner to those obtained at −50°C and it was again found that a parabolic term in log τ gave a better fit to the experimental data than simply a straight line.
The creep curves obtained at −70.C are shown in Figure 4 and their analysis is shown in Figures 5 and 6. In Figure 6, a straight line of slope n = 2.3 gave a better fit to the experimental data than the non-linear function. The results are summarized in Table I, from which it can be seen that m is independent of temperature.
Creep curves of ice single crystals deformed under various stresses at −70°C.
Creep curves of Figure 4 plotted logarithmically.
The stress dependence of the strain-rate of the crystals deformed at −70°C.
Parameters Determined For flow law
An attempt was made to obtain creep curves at −90°C but on all occasions the crystal fractured before any significant strain could be detected. As discussed by Reference Jones and GlenJones and Glen (1968), more specimens need to be tested at this temperature before it is possible to say categorically whether or not ice crystals are brittle at −90°C.
Activation-energy analysis
Details of this analysis have been given by Reference Jones and GlenJones and Glen (1968). It was found that between −10° and −50°C the activation energy was 0.68±0.04 eV (65±3 kJ/mol) and between −50° and −90°C it was 0.41±0.03 eV (40±2 kJ/mol).
Fracture Data
When the crystals fractured about 80% of them did so on a plane perpendicular to the tensile axis and very often at a point close to one of the end grips. The nominal stress applied to the crystal, that is, the load applied divided by the original cross-sectional area of the crystal rather than the resolved shear stress, was found to be the influencing factor. Tables II and III show results for different crystals with different values of θ, the angle between the tensile and optic axes. At −50°C large strains were only obtained when the nominal stress on the crystal was about 8 bar; if this stress was around 12 bar, fracture occurred within 20–30 h, after straining approximately 1%.
Fracture Data at −50° and −60°C
Fracture Data at −70 , −80° AND −90°C
For very short times, however, a crystal could sustain larger stresses, for example, crystal VA which existed under a stress of 16 bar for 2 h. The last column of Table II shows the tensile stress at the moment of fracture, assuming a uniform deformation. Since it is known that the crystals do not deform uniformly—they normally form a “ape”or “neck”—this column can only give a lower limit for the true tensile stress at the moment of fracture. Thus the actual tensile stress acting at the tape of crystal VIA after it had strained overall by 20% may well have been much larger than 9.5 bar.
At lower temperatures the fracture stress increased as can be seen from Tables II, III and IV. Although this increase in fracture stress was a help in obtaining a measurable deformation at the lower temperatures, it was not a large enough increase to compensate entirely for the loss of ductility at these temperatures.
Summary of fracture data
Constant Strain-Rate Tests
The apparatus and the method of using it have been described by Jones and Reference GlenGlen (1968). Cylindrical single crystals of ice, 1.5 cm in diameter and 3 cm in length, were compressed at a constant speed and stress-strain curves were recorded. The angle between the optic and tensile axes of the crystals was always close to 45°. Various temperatures were used in the experiment but only one nominal strain-rate, namely 2.7×10−7 s−1.
Typical stress–strain curves obtained in the compression tests are shown in Figure 7, for various temperatures, as marked on the curves. In general, as can be seen from this figure, no work hardening occurred during the deformation after the yield stress was passed—the stress continued to drop at a decreasing rate even to the quite large strains (resolved shear strains of 10%)observed in the experiment. In one test at −70°C, however, when resolved shear strains of up to 18% were observed, the stress did start to rise again at a strain of 15% as shown in Figure 8. This might have been a genuine work-hardening effect or it might possibly have been due to distortion of the crystal at large strains. It was only observed in the one test, but this was also the only test that continued to such large strains, because at the strain-rate used 4 days were needed to obtain a strain of 18%.
Stress–strain curves of pure ice single crystals obtained at strain-rate 2.7×10−7s−1, and at various temperatures.
Stress-strain curve of a crystal defornud at −70°C, showing an increase in stress at a strain of about 13%.
The effects of temperature and of annealing on the stress-strain curves were analysed in detail by Jones and Reference GlenGlen (1968).
Computed Stress-Strain Curves
It was decided to analyse the stress-strain curves obtained in this experiment along the lines of Reference JohnstonJohnston’s (1962) theory developed for lithium fluoride. A brief reference to some results of this analysis was made by Reference Jones and GlenJones and Glen (1968).
LiF has a stress–strain curve like that of ice in that it has an upper yield stress followed by a yield drop. It differs from ice in that at moderate strains, about 1–2%, work hardening becomes very marked. This is not of importance in applying the theory to ice because the initial theory was formulated for the case of no work hardening and an extra term, which can be neglected for ice, was added later to take work hardening into account. Reference JohnstonJohnston (1962) was able to use the experimentally known behaviour of dislocations in LiF, as determined by etch pit methods, to compute stress–strain curves which fitted the experimental ones satisfactorily.
The strain-rate 
of a deforming crystal was given by Reference CottrellCottrell (1953) as
where b is the Burgers vector of the dislocations, γ(ε) is the density of dislocations, which is a function of the strain, and v(τ) is the dislocation velocity which, at a constant temperature, is a function of stress. If only pure edge and pure screw dislocations are present in the crystal, and they move with different velocities, Equation (4) must be rewritten as
where the suffix s refers to screw dislocation and the suffix e to edge dislocation. Johnston considered the case when v s≪v e, as in LiF, and showed that Equation (3) can be simplified to
In LiF, the dislocation density increases linearly with strain so that with
with γ = 1013 dislocations/m2, and the dislocation velocity is given by
where D = 0.53 bar and p = 16.5. Thus the strain-rate is given by
An experimental stress-strain curve is obtained by causing a specimen to interact with a testing machine. The crosshead moves at a constant speed, S c, so as to compress the crystal against an anvil. Part of the crosshead motion goes into the elastic strain of the deforming fixture and crystal, which can be thought of as an imaginary spring of force constant, K. The elastic displacement is Δy el = F/K where F is the applied force. If ΔL p is the amount of plastic deformation of the crystal, the total crosshead displacement is
where t is the time. The plastic strain is
The plastic strain-rate is therefore
By converting the variables F and t to resolved shear stress τ and crosshead displacement y respectively, and substituting Equations (11) and (12) into (9) the equation
is obtained. C is given by K/2A, B = 2bα/S c, and τ = F/2A where A is the cross-sectional area of the specimen. Equation (13) is a reformulation of the strain-rate equation (5) incorporating the assumptions mentioned. For an initial pair of values (τ 0, γ 0) which is equivalent to specifying (τ 0, γ 0) where γ 0 is the initial number of mobile dislocation present in the crystal, the differential equation can, in principle, be integrated to obtain the stress-strain curve that the testing machine should produce under the same initial conditions. This is what Johnston did and he obtained good agreement with LiF stress-strain curves determined experimentally.
Unfortunately, we do not know how the individual dislocations in ice respond to stress, as no suitable etchant has been discovered which will show the basal dislocations. In other words, we do not know whether Equations (7) and (8) are valid for ice. It was decided to fit Equation (12) to the ice data, varying the parameters, until good agreement was obtained, in the hope of obtaining some useful information about the dislocations in ice. Therefore, Equations (7) and (8) were assumed to hold for ice and the effect of varying the parameters α, D, γ o and ρ for known K, the stiffness of the machine, and S c, the speed of compression was observed. Of these four parameters ρ is the best known since it should determine the stress dependence of the strain-rate of the crystals, and should therefore equal n of Equation (2). The effect of varying D is only to alter the scale of the stress-strain curve and does not alter the shape of the curve. The parameters γ 0 and α are least known for ice. It was assumed that α = 1013/m2 (as in LiF) and it was found that varying α, like varying D, did not alter the shape of the curve.
The effects of varying γ 0 and p are shown in Figures 9 and 10. Varying γ 0, keeping all the other parameters fixed, changes the upper yield stress but above all it alters the width of the peak. The effect of varying p, on the other hand, is to alter the yield drop, as seen from Figure 10, in which D has also been changed to keep the upper yield stress constant. Varying p does not alter the width of the curve, so that once the correct width of the computed curve has been obtained by varying γ 0, p can be varied to give the correct yield drop and D can be altered to give the correct upper yield stress.
The effect of varying γ 0, the initial number of dislocations, on the computed stress–strain curves.
The effect of varying p, of Equation (8), on the computed stress-strain curves. The upper yield stress is kept constant by adjusting D.
Such a fit is shown in Figure 11, in which the solid line is the computed curve and the open circles are experimental points for two crystals deformed at −50°C. The parameters used to fit the curve were p = 3.0, D = 1000 bar and γ 0 = 5×109 dislocations/m2. The value of p is in reasonable agreement with the value expected from the stress dependence of the strain-rate of the tensile creep experiment. The number of initial mobile dislocations is a lot higher than that found by Johnston in LiF (c. 107), but it may be a reasonable value for the method used to grow the crystals. The value of D gives a dislocation velocity of 1.7×10−8 m s−1 at the upper yield point, dropping to 0.21×10−8 ms−1 by the time the stress has fallen to 6 bar. It is not surprising that the velocities are small since the strain-rate used was only 2.7×10−7s−1. An explanation of this low dislocation velocity has been given by Reference GlenGlen (1968) based on the re-orientation of hydrogen bonds in ice.
A computed stress–strain curve (solid line) compared with the experimental points of two crystals deformed at −50°C.
Recent work by Reference Fukuda, Higashi and RiehlFukuda and Higashi (1969), using an X-ray topographical technique, has given a dislocation velocity of 10−5 ms−1 at −22°C. With an activation energy of 0.68 eV, as measured in the present paper, a velocity of 2×10−7 ms−1 at −50°C is computed from their value. It is difficult to know exactly the value of the stress acting on Fukuda and Higashi’s dislocations, since their experiments were conducted in bending, but they quoted a value of 100 bar, in which case their experimental value is in reasonable agreement with the value deduced in these calculations.
Acknowledgements
We should like to thank the Royal Society for the provision of the cold laboratory used in the preparation and handling of specimens, and the Science Research Council for a research studentship held by one of us (S.J.J.).
