Introduction

Glaciers are key indicators for assessing climate change in remote mountain areas where climate stations are rare or non-existent. Since the end of the Little Ice Age, and especially since the end of the last century, a nearly global glacier recession has been noticeable (Reference BarryBarry, 2006). Previous studies also show receding glaciers for most of the Himalaya (Reference Kadota, Seko, Aoki, Iwata and YamaguchiKadota and others, 2000; Reference Fujita, Kadota, Rana, Kayastha and AgetaFujita and others, 2001; Reference Ren, Jing, Pu and QinRen and others, 2006; S.C. Rai, http://assets.panda.org/downloads/himalayaglaciersreport2005.pdf). However, this does not imply a synchronous behaviour of all glaciers, because there can be local differences and even advancing glaciers. Multitemporal spaceborne images are ideal to study glacier changes in detail. In addition, they are the best way to investigate glaciers in remote mountainous areas. Multi-spectral satellite imagery represents an ideal tool for automated glacier mapping. A simple but robust method is the use of ratio image, (e.g. near-infrared/shortwave-infrared (NIR/SWIR) band such as Landsat Thematic Mapper 4 and 5 (TM4/TM5) or Advancesd Spaceborne Thermal Emission and Reflection Radiometer (ASTER) bands 3 and 4 (Reference Paul, Kääb, Maisch, Kellenberger and HaeberliPaul and others, 2002; Reference Bolch and KampBolch and Kamp, 2006)). However, many glacier tongues in the Himalaya are heavily covered by supraglacial debris (Reference Moribayashi and HiguchiMoribyashi and Higuchi, 1977) which hampers the automated delineation using multi-spectral imagery. A promising approach to map these glacier parts is to include morphometric information (Reference Bolch, Buchroithner, Kunert, Kamp and GomarascaBolch and others, 2008).

The earliest imagery suitable for automated glacier mapping is available from 1982 from the Landsat 4 (TM) sensor, which was equipped with SWIR bands capable of rapidly distinguishing snow/ice-covered areas from other surfaces. They have, however, no stereo-capability to address volume changes. This is especially needed to address the fluctuation of the debris-covered glaciers, because their change is mainly recognizable through downwasting (Reference Kadota, Seko, Aoki, Iwata and YamaguchiKadota and others, 2000).

Declassified satellite imagery is available for 1960–72 from American intelligence satellite missions. Early systems (Corona KH-1, KH-2, KH-3) carried a single panoramic camera, whereas later systems (KH-4, KH-4A and KH-4B) carried two panoramic cameras with a separation angle of 30°. For KH-4 (resolution <8 m), KH-4A and KH-4B (resolution ∼2–7 m) the two cameras are referred to as fore (forward-looking) and aft (rear-looking) and provide stereo coverage and the capability to generate digital terrain models (DTM) (Reference Altmaier and KanyAltmaier and Kany, 2002). The ASTER sensor on the Terra satellite, which was launched in 1999, captures stereo images in the NIR band (resolution 15 m) and is therefore also capable of DTM generation. The overall quality of these ASTER DTMs is good, although problems like height inaccuracies can occur, especially in terrain with high relief (Reference KääbKääb, 2002; Reference Kamp, Bolch and OlsenhollerKamp and others, 2005).

The aim of this study is to address the glacier area changes for the Khumbu Himal, Nepal, for different time periods using multitemporal satellite imagery, and to shed light not only on the downwasting of Khumbu Glacier but also on other debris-covered glacier tongues using DTMs from Corona KH-4 (year 1962) and ASTER (year 2002). The presented work is a contribution to the international programme Global Land Ice Measurements from Space (GLIMS) (Reference KargelKargel and others, 2005).

Study Area

The study area of the Khumbu Himal is situated at the main ridge of the Himalaya, south of Qomolangma (Fig. 1). The climate is influenced by the Indian monsoon, and 70–80% of the precipitation occurs during the summer months (Reference UenoUeno and others, 2001). The glaciers can be classified as‘summer-accumulation-type glaciers’ (after Reference Ageta and HiguchiAgeta and Higuchi, 1984). Thus, the glaciers are especially sensitive to summer temperature (Reference Kadota, Seko and AgetaKadota and others, 1993). Avalanches are an important feeding source for Khumbu Glacier, and are about twice as significant as direct snowfall (Reference InoueInoue, 1977).

Fig. 1.

Map of the study area based on ASTER data from November 2005.

About one-third of the glaciers in the Khumbu Himal are debris-covered (Reference Fujii and HiguchiFujii and Higuchi, 1977). The thickness of the debris cover of Khumbu Glacier increases towards its terminus and reaches up to several metres. It also increases from the middle of the glacier tongue to the lateral moraines (Reference Nakawo, Iwata, Watanabe and YoshidaNakawo and others, 1986; Reference Watanabe, Iwata and FushimiWatanabe and others, 1986). The termini of the debris-covered glaciers extend down to about 4900 m a.s.l., which is 300–400 m lower than the tongues of the glaciers with clean ice (Reference Moribayashi and HiguchiMoribyashi and Higuchi, 1977).

The end of the active debris-covered glacier tongue is not clearly identifiable and it is likely that the investigated tongues contain parts of stagnant ice at the front which are probably connected with the active glacier ice. However, these stagnant parts differ in their surface characteristics. They are smoother, and locally even sparse grass vegetation is able to grow. These surface features of Khumbu Glacier have been well described (Reference Iwata, Watanabe and FushimiIwata and others, 1980; Reference Watanabe, Iwata and FushimiWatanabe and others, 1986; Reference Gades, Conway, Nereson, Naito and KadotaGades and others, 2000). The end of the active glacier tongue is estimated to be about 3 km upstream (Reference FushimiFushimi, 1977; Reference Luckman, Quincey and BevanLuckman and others, 2007). The parts of stagnant ice are commonly included in the glacier boundary (e.g. for the Nepalese Glacier Inventory (Reference Mool, Bajracharya and JoshiMool and others, 2001)). During field surveys, the existence of small secondary moraines has been observed, which indicates vertical surface displacement (Reference Buchroithner and BolchBuchroithner and Bolch, 2007; Fig. 2).

Fig. 2.

Eastern margin of Nuptse Glacier with a small secondary moraine (arrow). Photograph: T. Bolch, 2006.

Several supraglacial ponds, ice cliffs and thermokarst are typical for these debris-covered tongues with a rough surface. Due to climate change, some of these ponds grow and form a supra- or proglacial lake, such as Imja lake. The formation of the latter has been well described (Reference Watanabe, Kameyama and SatoWatanabe and others, 1995). Even when comparing recent ASTER images of 2003 and 2005, the surface of Imja lake is growing. The danger of an outburst of these lakes (glacial lake outburst flood monitoring and early warning sytem, (GLOF)) is well known and has been the subject of several studies (e.g. Reference Yamada and WatanabeYamada and Watanabe, 1998; Reference QuinceyQuincey and others, 2007).

Looking at multitemporal space imagery, such as Corona (1962) and ASTER (2003; Fig. 3), at first glance it seems that these debris-covered glaciers are mostly stable. However, the recent glacier shrinkage results in increasing debris coverage and an increasing number and total area of supraglacial lakes. In addition, the surface, especially at the very distal part of the glacier, looks smoother and shows no significant indication of movement, steep ice cliffs or furrows. The latter could be demonstrated using multitemporal IKONOS and ASTER data or radar data (Reference Luckman, Quincey and BevanLuckman and others, 2007). It should be mentioned that a clear delineation of the glacier termini is also not possible, or at least only with a high degree of uncertainty with ultra-high resolution images (e.g. QuickBird, IKONOS) and even field observations. At this point, geophysical investigations seem to be required.

Fig. 3.

Khumbu Glacier: (a) Corona image from 1962; (b) ASTER image from 2003. Black lines represent the glacier outlines and the transition between the debris-covered and clean-ice glacier; lakes are represented in light blue.

Present Knowledge of Glacier Variations in the Khumbu Himal

The glaciers in the Khumbu Himal, as in most other parts of the Himalaya, show an average area loss and negative mass balances. However, although Khumbu Glacier has been subject to several studies, no comprehensive multitemporal glacier inventory, including recent data, exists thus far for the study area. A comparison of the glacier inventories from 1960 (Reference MüllerMüller, 1970) and 1975 reveals a retreat of most glaciers in the Khumbu region, but the area loss has not been quantified (Reference HiguchiHiguchi and others, 1980). The retreat probably accelerated in the 1980s (Reference YamadaYamada and others, 1992). Observations of the clean-ice glacier AX010, situated in the Shorong Himal southwest of the Khumbu Himal, show that since measurements began in 1978 mass balance has been negative and the mass loss accelerated in the 1990s (Reference Fujita, Kadota, Rana, Kayastha and AgetaFujita and others, 2001). The area of the same glacier shrunk between 1978 and 1999 from 0.57 to 0.42 km² (more than 26%; Reference Fujita, Kadota, Rana, Kayastha and AgetaFujita and others, 2001). Concomitant with the glacier retreat, the debris-covered areas increase on most of the glaciers (e.g. Khumbu Glacier (Reference Iwata, Aoki, Kadota, Seko and YamaguchiIwata and others, 2000)).

The change in debris-covered glacier tongues is mostly noticeable through downwasting, because the termini are often either more-or-less constant or the terminus change is not identifiable due to the massive debris cover. Reference Nakawo, Yabuki and SakaiNakawo and others (1999) calculated an average rate of 1–2 m a⁻¹ around the Everest Base Camp for Khumbu Glacier from flow velocity, glacier surface temperature estimates based on satellite data and glacier thickness estimates. The melt rate is lowest (close to zero) at about 4 km down-glacier from Everest Base Camp, where the debris cover is thick and the movement rate still high. Melt rate is highest (∼1.5 m a⁻¹) at the estimated transition zone between active and inactive glacier parts. We assume a slight surface lowering at the stagnant glacier part with thick debris cover. The reason for the high ablation rates in the debris-covered area is the strong ablation at the ice cliffs and around the supragacial lakes (Reference Inoue and YoshidaInoue and Yoshida, 1980; Reference Sakai, Takeuchi, Fujita and NakawoSakai and others, 2000). A detailed comparison based on surface measurements between 1978 and 1995 also shows melt rates of 0.4–1.0 m a⁻¹. The highest rates were measured at the places with thin debris cover and at the transition zone between the active and inactive glacier tongue (Reference Kadota, Seko, Aoki, Iwata and YamaguchiKadota and others, 2000). Between 1995 and 1999 the ablation rates doubled at the investigated surfaces around the Everest Base Camp, at the estimated transition zone between thin debris cover and clean ice and also in areas with thick debris cover (Reference Kadota, Naito and ConwayKadota and others, 2002). Detailed comparisons of the surface of Khumbu Glacier between 1978 and 1995 show that the areas with rough surface have increased both upwards and downwards of the transition zone. Therefore the areas with high ablation rates also increased. This is one reason for the higher rates of down-wasting (Reference Iwata, Aoki, Kadota, Seko and YamaguchiIwata and others, 2000). However, the parts with stagnant ice remained about the same.

Owing to the high melting rates, Reference Nakawo, Yabuki and SakaiNakawo and others (1999) assume that large parts of the glacier tongue will disappear in about 100 years. A simulation of the Khumbu Glacier tongue predicts the development of a depression in the year 2020 and the splitting of the ablation area into two unconnected parts after 2040: the stagnant ice area and the active ice, possibly with a lake in between (Reference Naito, Nakawo, Kadota and RaymondNaito and others, 2000). A recent study of the glaciers on the north side of Qomolangma indicates similar behaviour, at least since the start of investigations in 1966 (Reference Ren, Jing, Pu and QinRen and others, 2006).

Data and Methods

Imagery

Multitemporal and low-cost data from different sensors were applied to assess glacier change in the Khumbu Himal. The oldest data originate from the American Corona KH-4 sensor (1962) and the youngest from the ASTER sensor on board the Terra satellite (2005; see Table 1). Two ASTER scenes (2001 and 2005) were chosen. These scenes cover the Khumbu Himal and are, for the main area of interest, nearly cloud-free. The basis for georectification was the map ‘Mount Everest’ published in 1988 by the US National Geographic Society (NGS, 1988). Unfortunately, this map does not cover the whole area to the mountain ridges west of Khumbu Glacier, so this region had to be excluded. About 100 ground-control points (GCPs) were chosen for rectification purposes for each ASTER scene. Orthoimages were generated using the ASTER DTM (see below). The overall RMS _x,y error was less than one pixel (15 m; Table 1), despite the high relief differences. In addition, a cloud-free Landsat TM scene of 1992 obtained by the Global Land Cover Facility (GLCF) was referenced to these ASTER data. The accuracy is lower than that of the ASTER data (with higher resolution) but still acceptable (Table 1). The higher RMS _x,y results are mainly due to deviations around high mountain ridges and peaks. Three Corona strips were required to provide a cloud-free cover of the whole study area, while the snow cover was acceptable. The main disadvantage is the low contrast in the snow-covered areas which hampers glacier mapping. However, the lower glacier boundaries are identifiable when image-stretching procedures are applied. The RMS _x,y error is in the range of the ASTER data.

Table 1.

Remote-sensing data used

DTM generation and evaluation

For the ASTER DTM of the investigation area, a subset was drawn around Qomolangma containing all the debris-covered glaciers originating at Qomolangma, Lhotse and Nuptse. The DTM is based on scenes from 2001, 2002 and 2003. Using 18 GCPs determined on the basis of the Qomolangma map (NGS, 1988) and approximately 100 tie points for each scene, a DTM was generated from each stereo pair using the PCI Geomatica 9.1 software. The raw DTMs contained several data gaps, mainly situated at steep slopes, in shadowed areas and in snow-covered areas. In contrast, the valleys, including the debris-covered glacier tongues, are well represented. In post-processing steps, the three DTMs were combined and the remaining data gaps were filled with terrain information derived from the NGS map (Reference Buchroithner and BolchBuchroithner and Bolch, 2007). The quality of the final DTM is promising (Fig. 4a).

Fig. 4.

Comparison of (a) the ASTER-derived DTM from ∼2002 and (b) the Corona-derived DTM from 1962, including the surface of several debris-covered glaciers.

In order to assess the accuracy, 205 independent control points covering non-glaciated areas of the whole DTM were used and compared with elevations based on the NGS map. Shuttle Radar Topography Mission (SRTM) data were not used for quality control because of the coarser resolution of 90 m. The calculated RMS _z error of the SRTM data was 80.6 m. In order to calculate the error near the glaciers, the areas of the control points were reduced to a buffer area of 500 m around the glacier tongues. The error analysis shows that the ASTER DTM is too low on average, with an RMS _z error of about 30 m. However, the accuracy is acceptable given the very steep slopes and the high relief differences of up to 5000 m. In addition, the RMS _z error is significantly smaller in the areas around the glacier tongues (Table 2). However, the single ASTER DTMs are too coarse to recognize the expected glacier downwasting between 2001 and 2003.

Table 2.

Resolution and accuracy of the raw Corona and ASTER DTMs

The Corona DTM is based on one forward-looking and one aft-looking strip of the KH-4 sensor. Most of the target area is covered in both scenes and is situated near the centre of the images. The contrast is good, apart from the snow-covered higher elevations at Qomolangma, Lhotse and Nuptse and the steep slopes situated in the shadows. The most challenging tasks of these Corona data are caused by their complex image geometry. Also, especially during this early mission, the flight and acquisition parameters were very unstable. Therefore, image parameters have to be estimated. The RSG software (Remote Sensing Software Package Graz), which is an add-on to ERDAS Imagine, has a tool especially developed to estimate the Corona image parameters using GCPs. The sources for the >100 GCPs for the Corona DTM of the Qomolangma area were the NGS map and the orthorectified ASTER scenes. The same GCPs as for the ASTER DTM were used if they were identifiable in the Corona image. For the outer parts of the 200 km long Corona strips, where no other data were available (especially in Tibet), orthorectified Landsat Enhanced TM Plus (ETM+)- scenes downloaded from GLCF were used. The latter had to be included to calculate the camera position.

Besides these coarse data for the outer parts of the image strips, the x,y accuracy in the target area is <20 m (Table 1). Shape and surface characteristics, in particular the glacier surfaces, are better represented in the Corona DTM than in the ASTER DTM (Fig. 4b). This is also due to the higher resolution (20 vs 30 m). However, the Corona DTM has many data gaps and large elevation errors on the steep slopes and snow-covered mountain ridges. On average, this DTM is too low. A further problem is that the northwestern areas tend to be too high and the southeastern areas too low. This may be due to an unstable camera during image acquisition. Also, in the southeastern areas of the Corona image, fewer GCPs could be identified because of high snow cover and low contrast. The overall RMS _z error (>50 m) is therefore relatively high. However, as with the ASTER DTM, the errors in the area of interest are much less (Table 1) and the glacier surfaces are well represented (Fig. 4b). In addition, the relative accuracy (rather than the absolute accuracy) of the DTMs is most important for addressing glacier volume change. Figure 5 is a histogram of the frequency distribution of the height differences between the two DTMs. The mean elevation of the glaciated areas is lower than for the non-glaciated areas.

Fig. 5.

Histogram of the height differences between ASTER and Corona DTM.

In order to minimize systematic height errors, a first- and second-order trend surface were calculated based on the non-glaciated surface at elevations between 4500 and 5500 m a.s.l. where the debris-covered glaciers and their moraines are situated. Correction by these trend surfaces leads to significant improvements. The mean elevation difference is only about 3 m, the frequency distribution is higher and narrower (Fig. 5) and the RMS _z is lower (Table 3). The first-order trend correction is slightly better than the second-order trend correction. In order to estimate the error at the debris-covered glacier tongues, statistics for all areas with similar surface slope conditions to those at the tongues (0–25°) within a 500 m buffer around those tongues were calculated and analyzed. The mean elevation difference between the improved Corona DTM and the ASTER DTM is 0.7 m with a standard deviation of 9.6 m. These statistics vary slightly for each glacier (Table 3).

Table 3.

Relative accuracy of the Corona and ASTER DTMs for the whole non-glaciated areas and for a buffer of 500 m around the debris-covered glacier tongues

The height difference between the ASTER and the Corona DTM is shown in Figure 6. Obvious errors with deviations up to 300 m occur at the steep slopes (e.g. at the accumulation area of Lhotse Glacier and the headwall above), snow-covered peaks and areas of higher elevation (e.g. the mountain ridges between the debris-covered glaciers).

Fig. 6.

Difference between the surface elevations of Khumbu Glacier based on ASTER and Corona DTMs. Areas with no Corona DTM coverage or where the DTM generation failed are represented by the shaded ASTER DTM. For the profiles see Figure 7.

The elevation differences in the valleys and on gentle slopes rarely exceed 25 m and are mostly positive, whereas the differences are clearly negative at all glacier tongues. It seems there is also a surface lowering at the accumulation area of Khumbu Glacier. However, as nearly stable areas in the surrounding parts are at very steep slopes where the DTM generation failed, an error analysis cannot be performed. The large differences (>50 m) between Qomolangma, Lhotse and Nuptse are likely an error of the DTMs.

Results

Glacier area changes

The overall ice-covered area in the Khumbu Himal (comparing Khumbu, Nuptse and Lhotse glaciers) decreased between 1962 and 2005 by 5.3 ± 2% (∼0.12% a⁻¹; Table 4). The highest area loss can be found from 1992 to 2001 (∼0.25% a⁻¹) and the lowest between 1962 and 1992 (∼0.09% a⁻¹). The area loss seems to slow down, but this is not a significant trend due to the short period of 4 years (2001–05) and the small amount, which barely exceeds the error range. The debris-covered ice area increased significantly between 1962 and 2005, by nearly 2.5% (0.06% a⁻¹), despite the fact that the growing Imja lake, which formed after 1962, was totally excluded from Imja Glacier.

Table 4.

Changes of total ice cover, the clean-ice and debris-covered ice areas in the Khumbu Himal between 1962 and 2005 based on spaceborne imagery

It should also be mentioned that, according to the local people (Reference Nakawo, Yabuki and SakaiNakawo and others, 1999), the increase of the debris cover in the pinnacle zone near the Everest Base Camp is partly due to a landslide. However, this area is comparatively small and does not affect the overall trend. The increase of the debris-covered areas is mainly due to the decrease of the clean-ice areas in the transition zone between clean and debris-covered glacier (Fig. 3). Accordingly, the clean-ice area decreased more than 10% (0.24% a⁻¹) between 1962 and 2005 (Table 4). The loss of the clean-ice areas was highest between 1992 and 2001 and lowest between 1962 and 1992.

Surface lowering

The values in Table 4 clearly show the importance of addressing the changes in the debris-covered areas in more detail. Existing investigations of the downwasting of debris-covered glacier tongues in the study area have concentrated on Khumbu Glacier, and are based only on point measurements or estimations. In order to address the volume changes, the Corona DTM (1962) and the ASTER DTM (2002) of Khumbu, Nuptse, Lhotse Nup and Lhotse glaciers were compared. Unfortunately, only about 50% of the ablation zone of Khumbu Glacier is covered by the Corona DTM (Fig. 1), and statistics refer only to this covered part.

A downwasting from about 11 m (Lhotse Glacier) to nearly 17 m on average (Khumbu Glacier) can be measured for all four glaciers (Table 5). However, the average downwasting exceeds the estimated errors clearly for only Khumbu Glacier, and is a little lower than the average DTM difference for Lhotse Glacier. Taking into account that the mean elevation of the surroundings for Lhotse Glacier is 5.2 m higher than for the ASTER DTM, there is still strong evidence for the downwasting of this glacier. In addition, the errors are less than the expected downwasting rates of more than 20 m, taking the results presented thus far for Khumbu Glacier into account (Reference Kadota, Naito and ConwayKadota and others, 2002). Therefore, the use of these DTMs is suitable to address the glacier downwasting.

Table 5.

Calculated downwasting and volume loss of the investigated debris-covered glacier tongues

Each glacier contains larger areas where the elevation difference between the ASTER and the Corona DTM is higher than 25 m. This is also confirmed with the length profiles. These profiles indicate that all debris-covered glacier tongues show similar behaviour (Fig. 7), i.e. a slight downwasting at the glacier snouts where the glaciers are presumably stagnant (e.g. Khumbu and Lhotse up to 2 km, Nuptse up to 1 km from terminus; average downwasting 5–15 m or 0.12–0.37 m a⁻¹). The downwasting is clearly pronounced in the middle part of the glaciers, where the transition zone between the active and inactive glacier parts might be situated (Khumbu, Lhotse 2–3 km, Nuptse 1.0–2.5 km from the terminus). Here, the average downwasting is >20 m (0.5 m a⁻¹),with maxima exceeding 50 m (1.25 m a⁻¹). The downwasting is less pronounced again in the upper highly debris-covered but presumably active part of the glacier. The average down-wasting rates are similar to those at the snout. The clearly visible peaks in the length profiles and areas where the ASTER DTM showed higher elevation values than the Corona DTM are most probably due to the different locations of prominent thermokarst formations and supraglacial ponds or inaccuracies in the DTMs.

Fig. 7.

Length profiles of Khumbu, Lhotse and Nuptse glaciers showing the deviation of the 2002 ASTER DTM and the 1962 Corona DTM which indicates the thickness changes. For the location of these profiles see Figure 5.

Discussion

The use of multitemporal space imagery for glacier monitoring is well known. Although the image geometry of the Corona images is very complex and the image processing and rectification is time-consuming, the data are of tremendous use in giving more insight into glacier changes since the early 1960s. This is mainly due to the high resolution (<10 m) and stereo capability. Moreover, these data are available for many remote mountain areas where no aerial images are available or accessible.

It could be demonstrated that Corona-based DTMs are suitable for comparative studies of glacier volumes. This study is one of the first presenting results using the early KH-4 stereo data with a resolution of about 8 m. Previously presented results, which were more accurate in elevation, made use of later KH-4A and KH-4B data with higher resolution (Reference Altmaier and KanyAltmaier and Kany, 2002).

The areal changes of the glaciers in the Khumbu Himal confirm the expected and widely published overall glacier retreat, but also quantify and give insight into the differences in the debris-covered and clean-ice areas for different times within the last 45 years. The pronounced glacier retreat in the 1990s shows behaviour similar to that of the well-investigated glacier AX10 (Reference Fujita, Kadota, Rana, Kayastha and AgetaFujita and others, 2001). Whether the less pronounced shrinkage at the beginning of the 21st century represents a stable trend needs further investigation. The use of suitable remote-sensing data from the early 1980s (such as aerial photographs from the NGS survey) would give even more insight into glacier change and would probably confirm the beginning of the pronounced glacier retreat in the 1980s (evidence based on ground surveys; Reference YamadaYamada and others, 1992) of selected glaciers. The present study also confirms the assumption that concomitantly with the glacier retreat, the debris-covered areas increase not only on Khumbu Glacier (Reference Iwata, Aoki, Kadota, Seko and YamaguchiIwata and others, 2000) but also on all other glaciers in the investigation area.

The calculation of the surface lowering based on the Corona and ASTER DTMs certainly contains errors due to the uncertainties of the DTMs. However, the characteristics of the surface changes are very well represented, and the calculated lowering rates for Khumbu Glacier are in agreement with the estimates of Reference Nakawo, Yabuki and SakaiNakawo and others (1999) and Reference Kadota, Seko, Aoki, Iwata and YamaguchiKadota and others (2000). Reference Kadota, Seko, Aoki, Iwata and YamaguchiKadota and others (2000) measured the surface changes between 1978 and 1995 to be 10–14 m (0.6–0.8 m a⁻¹) about 3 km upstream of the terminus. The calculated average downwasting between 1962 and 2002 based on the ASTER and Corona DTMs of the same area is ∼20 m (∼0.5 m a⁻¹).The study also confirms the lower but still evident downwasting rates in the heavily debris-covered active ice areas and the snout with thick debris cover. In addition, the DTM comparison sheds light on the characteristics of the downwasting not only of Khumbu Glacier but also, for the first time, of Lhotse, Lhotse Nup and Nuptse glaciers. The overall volume loss from the investigated glaciers is less than reported for debris-covered glacier tongues in the western Himalaya (Reference Berthier, Arnaud, Kumar, Ahmad, Wagnon and ChevallierBerthier and others, 2007), but is still significant.

The findings concerning glacier recession and down-wasting are important not only in improving knowledge about glacier water resources and the contribution of Himalayan glaciers to sea-level rise, but also in assessing preglacial and supraglacial lake development for the risk of outburst flood. The downwasting of the investigated debris-covered glaciers is pronounced about 1–3 km upstream of the terminus in an area where the transition between the active and the stagnant ice is expected. This can lead to a depression which is likely to be filled by a glacial lake (e.g. for Khumbu and Nuptse Glaciers with flat termini) and confirms the simulation by Reference Naito, Nakawo, Kadota and RaymondNaito and others (2000) for Khumbu Glacier. In contrast, the development of a large lake is less probable for Lhotse Glacier, due to less pronounced downwasting and especially due to the steeper terminus (Reference QuinceyQuincey and others, 2007).

Conclusions

This study, based on multitemporal space imagery from 1962, 1992, 2001 and 2005, shows an average area loss from the glaciers in the Khumbu Himal of about 5%. The highest retreat rates are found between 1992 and 2001. The coverage of the glaciers with debris increased concomitantly with a decrease in total glacier area.

The DTM generation from the early Corona KH-4 stereo data in this type of high-relief terrain is difficult and time-consuming, and still contains some elevation errors. Nevertheless, it was shown that DTMs based on space imagery are suitable for monitoring debris-covered glaciers, and a comparison of DTMs demonstrated glacier downwasting. The estimated volume loss for the investigated debris-covered glacier tongues is 0.19 km³ over the period 1962–2002. The highest downwasting rates (e.g. >0.5 m a⁻¹ for Khumbu Glacier) can be found in the expected transition zones between the active and the stagnant glacier parts of the debris-covered glacier tongue about 1–3 km upstream of the terminus. This may lead to the development of glacial lakes.

Existing and forthcoming sensors and data with stereo capabilities and resolutions of about 2.5 m, such as the optical advance Land Observing Satellite (ALOS), Cartosat and Terra-SAR-X, will provide more insight into the behaviour of debris-covered glaciers.