Simulation parameters

To study the generation of the REM and the reflection of the probe laser by the REM, we performed two-dimensional particle-in-cell (2D PIC) simulations using the Vorpal code (Nieter and Cary, Reference Nieter and Cary2004). The schematic drawing of the interaction process is shown in Figure 1. An ultra-intense femtosecond laser pulse normally illuminates on a nanofoil. The electrons in the target are pushed out as a whole electron layer, which forms a REM. During the acceleration of the electron layer, a second probe laser pulse irradiating normally on the layer can be reflected, producing an isolated radiation pulse. The simulation box has a size of 10λ × 20λ in the zx plane, and spacial resolution of 1000 cells/λ both in the z and x direction. The main laser is linearly polarized along x axis and propagates from the left boundary of the simulation box to right. This pulse has a profile of a ₀sin ²(πt/T) with pulse duration T = 4λ/c and wavelength λ = 800 nm. The transverse intensity profile is exp( − r ²/R ²), where R = 5λ is the transverse half width at 1/e ² of maximum intensity. The normalized laser field a ₀ is 100. The counter-propagating probe laser is linearly polarized along y axis and propagates from the right boundary of the simulation box to left. The parameters of the counter-propagating probe laser are all the same with the main laser except for the smaller normalized laser field a ₀ = 0.1. The smaller intensity can make sure that the REM would not be disturbed distinctly by the probe laser. An ultra-thin nanofoil is used as the target placed perpendicular to the main laser direction. The foil is located at z ₁ = 5λ = 4 μm with a thickness of d = 2.4 nm. The electron density of the target is n _e = 1.315 × 10²⁹/m³, corresponding to 75 n _c. n _c is the critical density for laser wavelength of 800 nm.

Fig. 1.

Schematic drawing of the interaction process in our PIC simulations.

Simulation results and analysis

At two chosen moments 14.7 and 15.4 fs, the spatial distribution of REM and the corresponding radiation field at the same time are shown in Figure 2. Figure 2(a) and 2(c) clearly shows that the electrons in the REM are accelerated to tens of MeV within less than 1 fs. The photon energy of the generated radiation is related to the electron energy. For the early time, the smaller electron energy will lead to radiation with a longer wavelength. As Figure 2(b) shows, the generated radiation field within the area of the REM only contains one half cycle. Then under higher electron energy, Figure 2(d) shows that several cycles are contained within the area of the REM. This temporal changing wavelength is the typical feature of the chirped pulse. Actually, the generation of the chirped attosecond pulses can also be observed in many previous simulation results (Wu et al., Reference Wu, Meyer-ter-Vehn, Fernández and Hegelich2010; Bulanov et al., Reference Bulanov, Esirkepov, Kando and Koga2016).

Fig. 2.

The spatial distribution for (a), (c) the electron layer and (b), (d) the generated radiation field at the same time. The first and second row correspond to the results at 14.7 and 15.4 fs, respectively. The unit of the radiation field is 10¹⁰ V/m.

In order to analyze the generation process of the reflected radiation, the relation between the reflected field and the corresponding generation moment can be obtained from the simulation results as shown in Figure 3(a). In Figure 3(a), there is an unusual intense peak right after the moment of 14.21 fs. This peak is generated at the second half cycle of the probe laser, where the peak laser field is four times lower than the maximum laser electric field. So, the reflectivity near this peak is obviously amplified. Then, the following emission will be terminated due to the destructive interference when the thickness of the REM becomes larger than half of the wavelength of the generated radiation.

Fig. 3.

(a) The relation between the radiation electric field and the corresponding generation moment. The field is divided into three sections which are indicated by the blue dash dotted lines. (b) The evolution of real energy γ₁ (red solid line) and the resonance energy γ₂ (black dashed line) of REM. (c) The spectra for the three sections are indicated by τ₁, τ₂, and τ₃.

To understand such unusual amplification, the temporal evolution for the electron energy and density of the REM can be drawn from the simulation results. The plasma frequency of the REM is

(1)$${\rm \omega}_{\rm e} = \sqrt{n_{\rm e}\lpar t\rpar e^2/m_{\rm e}{\rm \varepsilon}_0}\comma\; $$

where n _e(t) is the average electron density in the central part of the REM at different moment, ɛ₀ is the permittivity of free space, e is the electron charge, and m _e is the electron mass. For the REM with the energy of γ₁mc ², where ${\rm \gamma }_1 = 1/\sqrt {1-\lpar v_0/c\rpar ^2}$ is the average electron normalized energy and v ₀ is the electron velocity. Through the Lorentz transformation from the lab frame of reference to the REM moving frame of reference, the laser frequency ${\rm \omega}'_{\rm L}$ in the REM moving frame of reference can be obtained as

(2)$${\rm \omega}'_{\rm L} = {\rm \gamma}_1\lpar {\rm \omega}_{\rm L}-{\bf {\rm \beta}}\cdot k_0c\rpar \simeq2{\rm \gamma}_1{\rm \omega}_{\rm L}\comma\; $$

where ω_L and β = v ₀/c are the laser frequency and normalized electron velocity in the lab frame of reference, respectively, and k ₀ is the laser wave vector.

When ${\rm \omega}'_{\rm L}$ is equal to the frequency ω_e in the REM moving frame of reference, the resonance between the laser field and the plasma oscillation in the REM can lead to the amplification of reflection. Under the resonance condition, the normalized energy of REM must satisfy the relation of

(3)$${\rm \gamma}_2\lpar t\rpar = {{\rm \omega}_{\rm e}/\sqrt{{\rm \gamma}_1}\over \lpar {\rm \omega}_{\rm L}-{\bf {\rm \beta}}\cdot {\bf k}_0c\rpar } = {\sqrt{n_{\rm e}\lpar t\rpar e^2/m_{\rm e}{\rm \varepsilon}_0/{\rm \gamma}_1}\over \lpar {\rm \omega}_{\rm L}-{\bf {\rm \beta}}\cdot {\bf k}_0c\rpar }\comma\; $$

which is determined by the instant density n _e(t).

The evolution of γ₁ and γ₂ is shown in Figure 3(b). Initially when the electrons are static, γ₁(t < 13.8 fs) = 1, ${\rm \omega}'_{\rm L}$(t < 13.8 fs) = ω_L, and the density n _e(t < 13.8 fs) = 75 n _c ≫ n _c. The probe laser is reflected without blue shift, as shown in the first half cycle in Figure 3(a). Then during the acceleration of REM, γ₁ keeps increasing and n _e keeps decreasing due to the expansion of the REM. According to Eq. (3), γ₂ will be reduced due to the increasing of γ₁ and the decreasing of n _e. The turning point is indicated by the vertically dashed black line both in Figure 3(a) and 3(b) at the moment t ₀ = 14.21 fs. The two lines in Figure 3(b) intersect at this point. Within a very short time interval right after this moment, the resonance condition between the laser field and the plasma oscillation in the REM is satisfied, which will lead to the following amplification of reflection. Then with the continuous acceleration and expansion of the REM, γ₁ will be greater than γ₂ after a very short time. So the amplification due to the resonance will be terminated quickly.

In order to control and adjust the radiation spectra, it is necessary to analyze the temporal evolution of the radiation spectra. The radiation field in Figure 3(a) can be divided into three sections indicated by τ₁, τ₂, and τ₃. Through Fourier analysis, the spectra for the three sections are, respectively, obtained as the three lines in Figure 3(c). For the first section indicated by τ₁, the reflected field under the resonance condition is included. The spectrum obtained from Fourier analysis shows that this section mainly contributes to the harmonics of ω < 10ω₀. Using the formula

(4)$${\rm \gamma}_{\rm R} = {\rm \gamma}_1^2\lpar 1 + {\rm \beta}\rpar ^2{\rm \omega}_{\rm L}\comma\; $$

the central radiation frequency γ_R under the resonance γ of 1.69 is 9.25ω_L, which is consistent with the results from Fourier analysis. Then with the acceleration of the REM, the energy of the later generated photons will be higher. The section corresponding to τ₃ mainly contributes to the harmonics of ω > 20ω₀, while the contribution of the section corresponding to τ₂ is much less than those for τ₁ and τ₃. The analyses on the temporal evolution of the radiation spectra confirm our previous conclusion that the generated radiation is a chirped attosecond pulse. Although the total duration of the chirped pulse is about 2 fs, selective frequency filtering for the spectra can be used to choose a certain part of the radiation pulse. So, attosecond pulse can be obtained from the selective frequency filtering.

Based on the results in Figure 3(b) and 3(c), one way to control and adjust the radiation spectra can be obtained. Through adjusting the origin position of the probe laser, the relative time delay between the probe laser and the REM can be adjusted. Set the results in Figures 2 and 3 corresponding to the probe laser released at delay 0 μm. The origin position of the probe laser can be adjusted from −0.5 to 2.0 μm. The closer release of the probe laser will make the probe laser reach the REM earlier. The corresponding field and spectra are shown in Figure 4. When the origin position is adjusted from 0 to −0.5 μm, the red solid line in Figure 4 shows that the lower harmonic components (ω < 10ω₀) are amplified. This amplification can be due to the higher laser field intensity at the resonance moment. Next when the REM is accelerated to higher energy, the lower laser field intensity will lead to the depression of the higher harmonic components (ω > 30ω₀). On the contrary, when the delay is changed from 0.1 to 2.0 μm, the further release of the probe laser will make the probe laser reach the REM later. The laser field intensity at the resonance moment will be lower for the further delay. So, the reflected field intensity near the resonance moment and the lower harmonic components (ω < 30ω₀) will be depressed. At this condition, the laser field intensity will be higher when the higher harmonic components (ω > 40ω₀) are generated. So the higher harmonic components will be amplified.

Fig. 4.

(a) The reflected field for the different delay of the probe laser. The z position of the result for the delay of −0.5 μm is slightly shifted in order to be shown with other results in the same frame. (b) The spectra of the reflected field for the different delay of the probe laser.

Summary and discussion

In conclusion, our numerical studies show that REM with ultra-high acceleration and expanding velocity can be produced from a solid nanofoil illuminated normally by an ultra-intense femtosecond laser pulse with a sharp rising edge. Isolated chirped attosecond pulse can be produced through the reflection of an ultra-short probe laser on the accelerating REM.

The acceleration and expansion of the REM will make the plasma frequency of the REM equal to the frequency of the probe laser in the REM moving frame of reference within an ultra-short time interval. So, the reflected radiation near this interval could be obviously amplified due to the resonance between laser field and the plasma oscillation in the REM. The field of the reflected radiation could also be selectively amplified or depressed, through adjusting the arriving time of the probe laser. For the chirped pulse, the controlling of the field will lead to the selective adjustment of the corresponding spectra. Based on the multi-petawatt laser facility in laser Fusion Research Center (Zeng et al., Reference Zeng, Zhou, Zuo, Zhu, Su, Wang, Wang, Huang, Jiang, Jiang, Guo, Xie, Zhou, Wu, Mu, Peng and Jing2017), the corresponding REM generation and radiation experiments can be conducted in our next work.