Thermal Analysis Methodology

Thermal analysis is a ubiquitous and widely used general term that refers to a number of analytical methods monitoring the change in a material’s property with temperature, usually measured over small intervals of time or temperature change. The principles and various methods have been described in numerous reviews and books (Byrn et al., Reference Byrn, Zografi and Chen2017; Gabbott, Reference Gabbott2008; Plante et al., Reference Plante, Fernández and Leifeld2009), including excellent, in-depth reviews devoted specifically to clay minerals (Emmerich, Reference Emmerich and Christidis2010; Stucki et al., Reference Stucki, Bish and Mumpton1990). Therefore, the present paper focuses only on the application of thermal analysis to smectites (also applicable to vermiculites and smectite-interstratified phases) and only to smectites in a form corresponding to their most common natural occurrence in rocks and sediments, i.e. having inorganic interlayer cations. Thermal analysis of smectites with adsorbed organic compounds is a field in and of itself with dedicated reviews (e.g. Xi et al., Reference Xi, Martens, He and Frost2005; Plante et al., Reference Plante, Fernández and Leifeld2009; Yariv et al., Reference Yariv, Borisover and Lapides2011).

Among many thermal analysis methods (see Emmerich, Reference Emmerich and Christidis2010), a few have been used widely for smectites and related clay minerals, and are the most meaningful for their characterization: thermogravimetric analysis (TGA), differential thermal analysis (DTA), and its modern successor – differential scanning calorimetry (DSC). If a sample is analyzed simultaneously using more than one of the techniques (e.g. TGA and DTA), such a mode of analysis is often referred to as Simultaneous Thermal Analysis (STA). The evolved gas analysis (EGA), which allows determination of the composition of gases and vapors evolved from a sample during heating in a TGA or DTA/DSC analyzer, is a form of STA. Among the different means of analyzing gas evolved from clay samples, infrared spectroscopy (IR) and mass spectrometry (MS; also coupled with gas chromatography – GC-MS) are the most commonly used.

Thermogravimetric analysis presents weight change with temperature or time. In most cases this corresponds to the extent of a clay’s weight loss (in mg or weight %) during heating in an inert gas atmosphere, such as N₂, Ar, or He. However, under specific circumstances, mass gain can occur during TGA experiments, i.e. when an oxidizing agent or water molecules are present in the sample’s environment. Common practice when reporting TGA results is to present a first derivative of the original mass change curve over time or temperature. Such a derivative is referred to as the DTG curve. Differential thermal analysis returns the temperature difference between the sample and an inert reference material under the same heating conditions. Similar to DTA, DSC measures the heat flow (J K^–1 mol^–1) needed to maintain the same temperature of the sample and the inert reference material, which enables the heat capacity to be obtained (Giese, Reference Giese, Stucki, Bish and Mumpton1990). All the methods mentioned require some kind of purge gas which, in general, is meant to remove the thermal reaction products. A moisture analyzer is a low-temperature alternative to the TGA instrument, capable of measuring weight change (usually due to dehydration) from room temperature typically up to 200 or 250°C, with no purge gas flow.

Any thermal analysis can be performed in two modes depending on the rate of heating: (1) isothermal – temperature is increased quickly to the desired value and kept constant for the remaining part of the experiment; (2) non-isothermal – temperature varies during the experiment. This mode is represented by, for example, heating or cooling with a constant rate to the final temperature. The most common way of performing thermal analysis is to use a predefined (isothermal or non-isothermal) temperature program. Controlled-rate thermal analysis (CRTA) is a specific case of non-isothermal or quasi-isothermal conditions in modern TGA instruments, where the sample’s reaction rate (e.g. weight loss per time) is set as constant, but the heating rate varies (Ding & Frost, Reference Ding and Frost2002; Rouquerol et al., Reference Rouquerol, Rouquerol and Llewellyn2013). As the temperature controller keeps the reaction rate constant during CRTA, temperature change with time for a particular experiment is not known beforehand. Whereas DTA and DSC usually need the linear heating/cooling mode (with exceptions, see Boller et al., Reference Boller, Jin and Wunderlich1994), TGA can operate in any isothermal or non-isothermal mode, or a combination of both.

Measurement Accuracy and Precision

Thermal-reaction temperatures are commonly reported based on the position of the corresponding DTG or DTA peak. A number of factors affect the position of the peak, which can hamper straightforward comparisons among reaction temperatures reported in various studies (Emmerich, Reference Emmerich and Christidis2010). First, a positive correlation occurs between the DTG or DTA peak temperatures and the heating rate in non-isothermal conditions due to kinetic effects. Second, the peak temperature is dependent on the particular thermal analyzer’s temperature calibration, which should be based on at least two points in the range corresponding to the tested reaction. Curie temperature reference materials are commonly used for TGA instruments, whereas temperature and enthalpy of fusion are used in DTA and DSC instruments (Della Gatta et al., Reference Della Gatta, Richardson, Sarge and Stølen2006). Theoretically, ~1 K (1°C) should be considered as a standard error in the thermal analysis of smectite in well-calibrated instruments. In practice, however, several factors may cause the actual sample temperature to deviate from the measured value even more (see Emmerich, Reference Emmerich and Christidis2010 for comprehensive review). As a result of a poorly crystalline structure, heterogeneous cation distribution, the particularly small size of its crystallites (both planar and crystallite thickness), and their diverse means of agglomeration, smectite samples do not return sharp, well-defined thermal events. These features, along with operator-dependent choices during data mathematical processing, all result in the real accuracy and precision of determining reaction temperature being in the range of a few °C.

Accuracy of the mass-loss measurement can be tested using a homogeneous material with a well-constrained mass loss in a given temperature interval, such as Ca-oxalate monohydrate (Bish & Duffy, Reference Bish, Duffy, Stucki, Bish and Mumpton1990; Plante et al., Reference Plante, Fernández and Leifeld2009). Thermal drift (i.e. the profile of mass or heat flow change with temperature in the absence of any reactive material) should be measured for each thermal analysis instrument and a mode of analysis. Thermal drift can be determined on an empty pan or an unreactive sample with a well-calibrated instrument under conditions corresponding to the experimental sample analysis and the test results should be applied to correct an experimental sample curve. A well-calibrated TGA instrument and method should return the mass-loss precision in the range of 0.1%.

Dehydration

Dehydration is the loss of molecular water (H₂O) adsorbed on or within clay-mineral particles. Upon drying, H₂O molecules are removed sequentially following the strength of their interactions with the smectite surface. The entire physisorbed water condensed in meso- and micropores of particles is removed at room temperature under the flow of dry purge gas. Bulk (bound via H-bonds to other H₂O molecules) smectite interlayer water is in equilibrium with the external moisture and, therefore, it is removed along with the physisorbed water albeit at a lower rate (Emmerich et al., Reference Emmerich, Giaudo, Schuhmann, Schnetzer, Kaden and Thissen2018; Ferrage et al., Reference Ferrage, Lanson, Michot and Robert2010; Salles et al., Reference Salles, Douillard, Denoyel, Bildstein, Jullien, Beurroies and Van Damme2009). Therefore, distinction between the bulk interlayer and the external, physisorbed water is hardly possible in thermal analysis as no temperature–time cutoffs are applicable. The removal of physisorbed and bulk interlayer water is completed much below 100°C. Due to the difference in solidification and fusion temperatures of physisorbed water, the DSC-based thermoporometry (freezing conditions, below 0°C) is the best temperature-differentiation method that can be applied to address the distinction between total interlayer and micropore capillary water (Grekov et al., Reference Grekov, Montavon, Robinet and Grambow2019; Salles et al., Reference Salles, Bildstein, Douillard, Jullien, Raynal and Van Damme2010).

In a fully hydrated smectite, some water molecules form a hydration shell around the smectite’s interlayer cations. Once the bulk interlayer water is removed during dehydration, the remaining H₂O molecules become organized around the interlayer cations in a fashion and number dependent on the cation’s hydration energy (Salles et al., Reference Salles, Douillard, Bildstein, El Ghazi, Prélot, Zajac and Van Damme2015), expressed as the cation’s hydration enthalpy (Table 1). The larger the absolute value of the cation hydration enthalpy (see Table 1 for an explanation of ΔH ^o), the lower the probability for the cation to bind directly to the smectite’s siloxane surface, the stronger the interaction between water molecules and the interlayer cation, and, therefore, the greater the energy that is required to remove any remaining strongly bound water (Webb et al., Reference Webb, Stanley and Scheiner1986).

Table 1

The hydration enthalpy (–ΔH ^o) after Smith (Reference Smith1977) and effective ionic radii for a given coordination number of inorganic cations commonly occurring in smectite interlayers in natural conditions and used in laboratory experiments, after Shannon (Reference Shannon1976)

^* After Sidey (Reference Sidey2016)

The cation’s hydration enthalpy is reflected by the pattern of smectite dehydration. Except for Li⁺-saturated smectites, the interlayer’s monovalent cations produce a single DTG dehydration peak below 100°C, whereas two DTG peaks or a high-temperature shoulder (up to ~200°C) usually correspond to high-enthalpy cations (polyvalent and Li⁺; Fig. 2; El-Barawy et al., Reference El-Barawy, Girgis and Felix1986). The fewer the H₂O molecules around interlayer cations, the greater the activation energy (E _a) of dehydration and the higher the temperature needed to remove the remaining H₂O. In extreme cases, H₂O dissociation leads to the hydrolysis of interlayer cations by OH that can remain in the smectite interlayer, even up to 500°C, which affects the course of dehydroxylation (Kuligiewicz & Derkowski, Reference Kuligiewicz and Derkowski2017).

Fig. 2

DTG curves in the temperature range corresponding to the dehydration of Na⁺-, Ca²⁺-, and La³⁺-exchanged montmorillonites. The analysis was performed under dry N₂ at a flow of 50 mL/min, with a constant heating rate of 5°C/min

NH₄ ⁺-exchanged smectites show very low mass loss due to dehydration as the ammonium cation has a low hydration enthalpy (Table 1); however, the smectite undergoes an exothermic deammonization reaction at 300–400°C resulting in weight loss and leaving smectite in H⁺ form (Mackenzie & Bishui, Reference Mackenzie and Bishui1958; Seiffarth & Kaps, Reference Seiffarth and Kaps2009).

Unless a sample contains an impurity that provides mass loss at low temperature (< 200°C, e.g. gypsum, zeolites, halloysite, and soil organic matter; see the Impurities section below), the quantity of H₂O removed from a clay during thermal dehydration corresponds to the smectite content in a sample (both as a discrete mineral and as a fraction of smectite-interstratified phases), and also depends on the hydration enthalpy of the interlayer cation, and – to a minor extent – the smectite layer charge (Środoń & McCarty, Reference Środoń and McCarty2008; Środoń et al., Reference Środoń, Zeelmaekers and Derkowski2009; Webb et al., Reference Webb, Stanley and Scheiner1986). If used for a semi-quantitative estimation of smectite content, a sample needs to be pre-equilibrated at a selected relative humidity (RH) that produces a particular degree of interlayer H₂O filling, the latter also being dependent on the interlayer cation type (Berend et al., Reference Berend, Cases, Francois, Uriot, Michot, Masion and Thomas1995; Cases et al., Reference Cases, Bérend, François, Uriot, Michot and Thomas1997). Despite this ambiguity, the measured fraction of mass loss due to dehydration is good enough for a relative comparison among samples tested. For example, pure Ca²⁺-saturated smectite equilibrated at ~50% RH contains ~16.5 wt.% of H₂O (as determined by drying at 200°C; Środoń & McCarty, Reference Środoń and McCarty2008); the corresponding mass loss upon dehydration decreases proportionally to illite interstratification in illite-smectite (Środoń et al., Reference Środoń, Zeelmaekers and Derkowski2009) and smectite mineral content in a sample (Środoń, Reference Środoń2009). When equilibrated at ~50% RH, dehydration would correspond to 6% mass loss in K⁺-saturated smectite, ~10% in Na⁺- and Li⁺-saturated smectite, and almost 20% in Mg²⁺-saturated smectite (Berend et al., Reference Berend, Cases, Francois, Uriot, Michot, Masion and Thomas1995; Cases et al., Reference Cases, Bérend, François, Uriot, Michot and Thomas1997). The above-mentioned semi-quantitative measurement should not be carried out under any dry gas purge (common in TG instruments) as it triggers dehydration during the sample-weight stabilization under dry gas flow; a moisture analyser is thus preferred (Środoń et al., Reference Środoń, Zeelmaekers and Derkowski2009).

Dehydroxylation

Dehydroxylation is the major thermal reaction of smectites and other 2:1 layer type clay minerals. It occurs between ~300 and 900°C and results in the extraction of a H₂O molecule formed by two adjacent OH groups and leaves one residual oxygen atom (O _r) in the structure:

(1) $2n{\left(\mathrm{OH}\right)}^{-}=n{H}_{2}O\uparrow +n{O}_r^{2-}$

where n is the number of water molecules eliminated during dehydroxylation.

The actual thermogravimetric manifestation of the reaction is the loss of H₂O after its migration through the interlayer and out of the crystallite. The theoretical mass loss upon dehydroxylation is calculated as the molecular weight of H₂O per a smectite’s formula unit molecular weight. Dehydroxylation produces an evolved gas pattern of H₂O exactly following the DTG curve and TG mass loss, corresponding quantitatively to Eq. 1 (Fig. 1). In Ca²⁺- or Na⁺-exchanged Fe-poor smectites mass loss corresponding to dehydroxylation is 4.7–4.9%, whereas in nontronite it can be as low as 4.3%. Exchanging a smectite with a heavy cation such as Cs⁺ can decrease the theoretical mass loss significantly. The smectite’s mass loss due exclusively to dehydroxylation may not be clearly distinguishable in TGA analysis, and thus, may not correspond to the theoretical value. In numerous dioctahedral smectites, especially those having an interlayer cation of high hydration enthalpy (Ca²⁺, Mg²⁺, etc.), the onset of dehydroxylation overlaps with the dehydration of residual, strongly bound water (Bray & Redfern, Reference Bray and Redfern2000; Kuligiewicz & Derkowski, Reference Kuligiewicz and Derkowski2017).

The first control on the temperature of dehydroxylation is the octahedral occupancy. In dioctahedral 2:1 layer phyllosilicates the proton from one OH group migrates either along the shared edge of the octahedron or jumps across the octahedral vacancy to join the adjacent OH group (Guggenheim et al., Reference Guggenheim, Chang and Koster van Groos1987; Ogloza & Malhotra, Reference Ogloza and Malhotra1989; Muñoz-Santiburcio et al., 2016). In dioctahedral smectites, dehydroxylation transforms the octahedral structural arrangement into a five-fold coordinated bipyramidal structure and the previously octahedral cations remain in a similar arrangement to the pristine structure (for details see Drits et al., Reference Drits, Besson and Muller1995). The 2:1 layer thus remains at least partially intact. In the case of trioctahedral phyllosilicates, due to the lack of an octahedral vacancy where the residual oxygen could reside, OH groups cannot be removed without a reconstruction of the octahedral sheet; their dehydroxylation is accompanied by recrystallization and occurs at higher temperatures than in dioctahedral species, therefore (Fig. 1). The high-temperature DTG peak (usually >700°C) can serve as a distinction between trioctahedral layers or domains and dioctahedral counterparts in natural smectites. Synthetic saponites, however, showed strong dependence of the dehydroxylation temperature on the octahedral sheet cation composition: Mg > Ni > Co > Zn (Vogels et al., Reference Vogels, Kloprogge, Geus and Beers2005). Vogels et al. (Reference Vogels, Kloprogge, Geus and Beers2005) proposed that the smaller the octahedral cations, the greater the corrugation of the tetrahedral sheet, which results in greater thermal stability.

For dioctahedral smectites, the next factor controlling the temperature of dehydroxylation is octahedral symmetry. Drits et al. (Reference Drits, Besson and Muller1995, Reference Drits, Lindgreen, Salyn, Ylagan and McCarty1998) showed that the cis-vacant (cv) structure has a significantly higher dehydroxylation temperature (>600°C) than the trans-vacant (tv) layer structure (< 600°C; Fig. 3). Those authors assigned that difference to the longer distance between non-shared OH edges in the cv structure than the shared OH edge of the octahedron in the tv coordination, resulting in the less probable and longer H⁺ jump between the OH groups in the cv coordination. Besides, in contrast to one-step dehydroxylation of tv layers, dehydroxylation of aluminous cv smectite is a two-step process that involves the Al cation migration to cis-sites and results in the pseudo-tv structure of the dehydroxylate (Drits et al., Reference Drits, Besson and Muller1995; Stackhouse et al., Reference Stackhouse, Coveney and Benoit2004), the same as that of the dehydroxylated pristine tv smectite. In tv Mg-Fe-rich smectites (e.g. nontronite), however, some cations migrate to trans-positions during dehydroxylation in order to redistribute the Fe–O bonds, resulting in a cv dehydroxylated structure (Muller et al., 2010a, b Drits & Zviagina, Reference Drits and Zviagina2009).

Fig. 3

DTG curves showing the difference in dehydroxylation of trans-vacant (tv) and cis-vacant (cv) dioctahedral smectites along their dominating octahedral cation-OH composition (after Derkowski et al., Reference Derkowski, Drits and McCarty2012a). Analysis preformed under dry N₂ at 50 mL/min flow, with a constant heating rate of 5°C/min

Following Drits et al. (Reference Drits, Lindgreen, Salyn, Ylagan and McCarty1998), Wolters and Emmerich (Reference Wolters and Emmerich2007) and Emmerich et al. (Reference Emmerich, Wolters, Kahr and Lagaly2009) adopted 600°C as the dehydroxylation temperature boundary and suggested using it for the determination of cv and tv compounds in smectites.

A broad temperature range of dehydroxylation is observed for all dioctahedral clay minerals, including smectites. Guggenheim et al. (Reference Guggenheim, Chang and Koster van Groos1987) and Guggenheim (Reference Guggenheim1990) explained this effect as a continuous recombination of bonds between the remaining OH and octahedral cations in a progressively dehydroxylated 2:1 layer. Drits et al. (Reference Drits, Derkowski and McCarty2012a,Reference Drits, McCarty and Derkowskib) and Derkowski et al. (Reference Derkowski, Drits and McCarty2012a) suggested that the reaction model is homogeneous; the 2:1 layers are only either non-dehydroxylated or completely dehydroxylated, but the temperature of maximum dehydroxylation as well as the temperature range of dehydroxylation are controlled by the bond strength between OH groups and octahedral cations, i.e. the octahedral sheet composition (Drits et al., Reference Drits, McCarty and Derkowski2012b) and the crystallite thickness distribution (see also Pérez-Maqueda et al., Reference Pérez-Maqueda, Blanes, Pascual and Pérez-Rodríguez2004, Perez-Rodriguez et al., Reference Perez-Rodriguez, Duran, Sanchez Jimenez, Franquelo, Perejón, Pascual-Cosp and Pérez-Maqueda2010). The latter is not applicable to smectites due to their ultrafine planar size and small crystallite thickness. The relative order of dehydroxylation temperature for tv dioctahedral smectites can be expressed by the following sequence (Derkowski et al., Reference Derkowski, Drits and McCarty2012a), (Fig. 3):

$\mathrm{Mg}-\mathrm{OH}-\mathrm{Mg}>\mathrm{Al}-\mathrm{OH}-\mathrm{Mg}>\mathrm{Al}-\mathrm{OH}-\mathrm{Al}>\mathrm{Al}-\mathrm{OH}-\mathrm{Fe}>\mathrm{Fe}-\mathrm{OH}-\mathrm{Fe}$

which is supported by the quantum mechanical calculations. The order of dehydroxylation temperature is controlled by the octahedral cation–OH bond strength, thus O…H distance (Molina-Montes et al., Reference Molina-Montes, Timón, Hernández-Laguna and Sainz-Díaz2008; Botella et al., Reference Botella, Timón, Escamilla-Roa, Hernandez-Languna and Sainz-Díaz2004). Although 300°C is applied commonly as the lowest temperature boundary of dehydroxylation (Fig. 3), long isothermal treatment provides energy sufficient to shift the onset of reaction to <300°C in the tv Fe-OH-Fe environment, i.e. nontronite (Środoń & McCarty, Reference Środoń and McCarty2008; Kuligiewicz & Derkowski, Reference Kuligiewicz and Derkowski2017).

Heterogeneity of the octahedral sheet’s cation composition contributes to the broad range of smectite dehydroxylation temperature; in smectite that has one cation species dominating the octahedral sheets the temperature range of dehydroxylation is narrower than those observed in smectites with heterogeneous octahedral composition (Drits et al., Reference Drits, Derkowski and McCarty2012a). In trioctahedral smectites the octahedral sheet is rarely fully occupied by cations. Locally occurring vacancies, e.g. in stevensite, produce dioctahedral domains which dehydroxylate at temperatures corresponding to the dioctahedral smectite (i.e. montmorillonite).

The interlayer cations’ hydration enthalpy controls the temperature of final dehydration and, thus, the degree of overlap for the dehydration and dehydroxylation reactions in some dioctahedral smectites (Kuligiewicz & Derkowski, Reference Kuligiewicz and Derkowski2017; Fig. 4). Also, the interlayer cation size and its potential for migration into the octahedral sheet play a role in the pathway of smectite dehydroxylation. Early DTA studies demonstrated that the interlayer cation influences the temperature of maximum dehydroxylation (El-Barawy et al., Reference El-Barawy, Girgis and Felix1986; Mackenzie & Bishui, Reference Mackenzie and Bishui1958). Later, Bray and Redfern (Reference Bray and Redfern2000) and Kuligiewicz and Derkowski (Reference Kuligiewicz and Derkowski2017) found differences in the kinetics of the dehydroxylation reaction in a smectite containing monovalent and divalent interlayer cations. Cs⁺ is the largest inorganic cation that can pillar the interlayer (Table 1), allowing H₂O molecules generated during dehydroxylation to diffuse easily, resulting in a decrease in the temperature of dehydroxylation in dioctahedral smectites (Fig. 4). The more beidellitic the smectite structure is, the greater the effect of Cs⁺-pillaring (Fig. 4: beidellite > beidellitic montmorillonite and nontronite > montmorillonite) because of the repulsion forces between adjacent siloxane surfaces created by Al substitution in the tetrahedral sheet and also the potential for the Cs⁺ cation to be located above the Al-substituted tetrahedra instead of the ditrigonal cavity (Cuadros, Reference Cuadros2002; Ngouana & Kalinichev, Reference Ngouana and Kalinichev2014). The cation size, however, seems to result in an opposite trend in trioctahedral smectites; the larger the interlayer cation, the higher the temperature of dehydroxylation (Fig. 4). The ability to block efficiently the ditrigonal cavity by a large cation, which suppresses H⁺ migration into the adjacent OH group, is likely the reason for this effect.

Fig. 4

DTG curves of smectite reference samples saturated with various inorganic cations. The analysis was performed under a 100 mL/min flow of dry N₂, with 4 h isothermal heating at the temperatures indicated on the figures, followed by heating to 1000°C at a constant rate of 5°C/min

In montmorillonites, where layer charge is generated in the octahedral sheet, dehydration enables small cations to migrate into the ditrigonal cavity of the tetrahedral sheet and even further into the octahedral vacancy, forming pseudo-trioctahedral domains (Emmerich et al., Reference Emmerich, Madsen and Kahr1999; Hofmann & Klemen, Reference Hofmann and Klemen1950; Komadel et al., Reference Komadel, Madejová and Bujdák2005, and references therein; Skoubris et al., Reference Skoubris, Chryssikos, Christidis and Gionis2013). The Hofmann-Klemen effect affects the pattern of dehydroxylation, forming an additional DTG peak at temperatures corresponding to trioctahedral domains. Not only Li⁺, commonly used in reducing layer charge, but also other small cations can produce such thermal effects. Koster van Groos and Guggenheim (Reference Koster van Groos and Guggenheim1989) explained differences observed between the dehydroxylation of Mg²⁺- and Ca²⁺-exchanged montmorillonite as resulting from the different abilities of Mg²⁺ and Ca²⁺ to migrate toward the residual oxygen during the dehydroxylation reaction. The ability to form pseudo-trioctahedral domains must then depend on the kinetics of dehydration and small-cation migration through the ditrigonal cavity. Indeed, as presented in Fig. 5, Li⁺ migration (Li⁺ –ΔH ^o = 519 kJ/mol; Table 1) forms the high-temperature DTG peak weakly dependent on the dehydration temperature prior to dehydroxylation, whereas Mg²⁺-montmorillonite (Mg²⁺ –ΔH ^o = 1921 kJ/mol; Table 1) produces a pseudo-trioctahedral DTG signature at ~900°C, which is proportional to the temperature and time of isothermal dehydration (Fig. 5). Fast dehydroxylation during ramp-heating itself may not be sufficient to quickly and completely dehydrate Mg²⁺ and fix the cation in the ditrigonal cavity or the octahedral sheet.

Fig. 5

The effect of cation migration into the octahedral sheet. DTG curves of Li⁺-exchanged and Mg²⁺-exchanged montmorillonites preheated isothermally under a flow of 100 mL/min of dry N₂ for 4 h at various temperatures (as stated in the legend) followed by heating to 1000°C at a constant rate of 5°C/min. The DTG curves of the SCa-2 sample saturated with other cations and preheated isothermally at 300°C are given as reference

Dehydrogenation

Dehydrogenation proceeds during thermal treatment of Fe(II)-bearing phyllosilicates, resulting in the removal of one hydrogen atom while simultaneously oxidizing one Fe(II) cation that is octahedrally coordinated with the OH group (Farmer et al. Reference Farmer, Russell, McHardy, Newman, Ahlrichs and Rimsaite1971; MacKenzie & Berezowski, Reference MacKenzie and Berezowski1984; Rancourt et al., Reference Rancourt, Mercier, Cherniak, Desgreniers, Kodama, Robert and Murad2001; Sanz et al., Reference Sanz, Gonzalez-Carreno and Gancedo1983; Wicks & Ramik, Reference Wicks, Ramik, Stucki, Bish and Mumpton1990).

In vacuum and in an inert gas atmosphere, the dehydrogenation reaction proceeds as follows:

(2) $2\left({\mathrm{Fe}}^{2+},+,{\mathrm{OH}}^{-}\right)\to 2\left({\mathrm{Fe}}^{3+},+,O_r^{2-}\right)+H_2\uparrow$

resulting in the formation of H• radicals that evolve from a sample as H₂ gas, which can be recorded in an EGA mass spectroscopy signal as m/z = 2 (Lempart et al., Reference Lempart, Derkowski, Strączek and Kapusta2020). The reaction proceeding via Eq. 2 produces negligible mass loss, 1/9 of that produced by dehydroxylation (Eq. 1). Dehydrogenation usually overlaps with the temperature range corresponding to dehydroxylation, which has led to numerous incorrect interpretations of the reaction mechanisms and products (Heller-Kallai & Rozenson, Reference Heller-Kallai and Rozenson1980). Dehydrogenation removes the hydroxyl H, reducing the amount of OH groups available for dehydroxylation, which results in a weight loss that is much lower than the theoretical value for dehydroxylation. In contrast to what has been reported in the literature, Fe(II)-free phyllosilicates do not undergo dehydrogenation and do not produce H₂ under normal pressure (Heide & Földvari, Reference Heide and Földvari2006 cf. Lempart et al., Reference Lempart, Derkowski, Strączek and Kapusta2020).

Under O₂-bearing gas (e.g. air), the reaction follows the same pathway as in Eq. 2, with H• radicals combined with ambient oxygen to produce H₂O.

(3) $2\left({\mathrm{Fe}}^{2+},+,{\mathrm{OH}}^{-}\right)+1/2O_2\to 2\left({\mathrm{Fe}}^{3+},+,O_r^{2-}\right)+H_{2}O\uparrow$

The presence of oxygen enhances dehydrogenation, shifting the reaction to lower temperatures. The MS curve of m/z = 18 of evolved gas in the reaction from Eq. 3 is excessive to the DTG curve, because H₂O is not produced within the heated crystallite and thus does not produce the corresponding weight loss (Lempart et al., Reference Lempart, Derkowski, Strączek and Kapusta2020).

In contrast to Eq. 3, only a specific portion of structural Fe(II) can oxidize under O₂ (e.g. air) following the reaction:

(4) ${2\mathrm{Fe}}^{2+}+\frac{1}{2}{O}_2\to {2\mathrm{Fe}}^{3+}+O_r^{2-}$

because the structural Fe(II) in a 2:1 layer is not readily available for binding with ambient oxygen and the reaction presented in Eq. 3 is preferred unless ^VIFe(II)/OH ratio > 1. Such a reaction as in Eq. 4 is possible during or after the high-temperature recrystallization when Fe(II) is exposed to ambient O₂ (Lempart et al., Reference Lempart, Derkowski, Luberda-Durnaś, Skiba and Błachowski2018).

Because of structural constraints, Fe(II) in natural smectites occurs in numerous trioctahedral species (Kohyama et al., Reference Kohyama, Shimoda and Sudo1973; Stucki, Reference Stucki, Stucki, Goodman and Schwertmann1988); therefore, these phases are the most prone to dehydrogenation. In nature, dehydrogenation may be responsible for the depletion of OH groups in so-called oxy-smectites (Dainyak et al., Reference Dainyak, Dritz, Kudryavtzev, Simanovitch and Slonimskaya1981). Dehydrogenation following Eq. 2 or Eq. 3 is expected upon heating Fe-reduced nontronites (Heller-Kallai, Reference Heller-Kallai1997a; Lear & Stucki, Reference Lear and Stucki1985).

In F-bearing smectites, usually trioctahedral and synthetic smectites (Christidis et al., Reference Christidis, Aldana, Chryssikos, Gionis, Kalo, Stöter, Breu and Robert2018), defluorination occurs as F• radical loss above 500°C and HF loss above 850°C (Heller-Kallai Reference Heller-Kallai1997b; Wicks & Ramik, Reference Wicks, Ramik, Stucki, Bish and Mumpton1990).

Smectite Structural Transformation upon Heating

Amorphization and recrystallization are the reactions that occur during thermal destabilization of the dehydroxylation and dehydrogenation products (Grim & Rowland, Reference Grim and Rowland1942a,Reference Grim and Rowlandb; Meyers & Speyer, Reference Meyers and Speyer2003). At temperatures higher than dehydroxylation, dioctahedral smectites undergo amorphization and then recrystallize into a topotaxic set of mullite, spinels, quartz or cristobalite, and pyroxenes (Bradley & Grim, Reference Bradley and Grim1951; Brett et al., Reference Brett, MacKenzie and Sharp1970). The degree and temperature of amorphization and transformation depends on the octahedral-sheet composition. Beidellite dehydroxylate is the most stable high-temperature smectite phase, the irreversible amorphization of which has not been observed below 900°C (Derkowski et al., Reference Derkowski, Drits and McCarty2012a; Derkowski & Kuligiewicz, Reference Derkowski and Kuligiewicz2017; Kawano & Tomita, Reference Kawano and Tomita1991b), whereas recrystallization occurs above 1200°C (Bradley & Grim, Reference Bradley and Grim1951). Sequentially heated Mg-rich dioctahedral smectites show an onset of amorphization at the end of dehydroxylation, whereas maximum amorphization is reached by ~800°C (Garg & Skibsted, Reference Garg and Skibsted2014;  Derkowski & Kuligiewicz, Reference Derkowski and Kuligiewicz2017), which provides their pozzolanic properties, but irreversibly removes their adsorption potential. In smectites rich in redox-active metals, i.e. nontronite, the temperature of transformation and the composition of transformation products depend heavily on the type of ambient gas (MacKenzie & Rogers, Reference MacKenzie and Rogers1977).

In trioctahedral smectites, transformation proceeds along with dehydroxylation; after initial amorphization, a pyroxene-like structure and an olivine-like structure are formed (Vogels et al., Reference Vogels, Kloprogge, Geus and Beers2005).

In contrast to dehydroxylation and dehydration, phase transformation is manifested in the DTA or DSC curves and not in TGA and TGA-MS, because it is not associated with a mass change or evolution of volatiles. However, note that at high temperature (>800°C), especially for isothermal experiments, some alkali cations can be removed due to vaporization, which may be responsible for occasionally observed minor and slow weight loss over a broad temperature range.

Rehydration and Rehydroxylation

Rehydration is the adsorption of H₂O molecules by a dried material. Rehydroxylation is the reconstruction of the structural OH groups, i.e. reversal of the reaction in Eq. 1, in a dehydroxylated smectite structure that has not undergone phase transition (amorphization or recrystallization). Whereas rehydroxylation in general must be preceded by H₂O diffusion through the dehydroxylated structure, advanced rehydroxylation requires specifically the diffusion within the interlayer in order to access all potential reaction sites available in the 2:1 layer. Both rehydration and rehydroxylation can be observed in situ as mass gain once wet gas is delivered directly to the TGA chamber (Derkowski & Kuligiewicz, Reference Derkowski and Kuligiewicz2017). When exposed to air, dried smectite having divalent cations in the interlayer starts resorbing H₂O from ambient moisture within seconds (Fig. 6; Kanik et al., Reference Kanik, Longstaffe, Kuligiewicz and Derkowski2022). For this reason, in practice, smectite material for rehydration and rehydroxylation tests also needs to be pre-dehydrated or pre-dehydroxylated in situ. The rate and extent of rehydration in pristine, dried (i.e. dried below the temperature of dehydroxylation) smectite depends heavily on the pre-drying conditions and, thus, the extent of interlayer cation fixation, and the temperature and RH during rehydration (Fig. 6; Derkowski et al., Reference Derkowski, Drits and McCarty2012b, Gailhanou et al., Reference Gailhanou, Vieillard, Blanc, Lassin, Denoyel, Bloch, De Weireld, Gaboreau, Fialips, Madé and Giffaut2017). Structurally, the extent of rehydration is controlled by the bonding between the siloxane surface and the interlayer cation; the greater the layer charge and the lower the cation hydration enthalpy, the stronger the bonding. K⁺-exchanged high-layer charge smectites would not rehydrate extensively keeping their interlayer closed, whereas Ca²⁺-exchanged smectite is prone to fast rehydration (Derkowski et al., Reference Derkowski, Drits and McCarty2012b; Kawano & Tomita, Reference Kawano and Tomita1991a, Reference Kawano and Tomitab). Once a small interlayer cation, like Li⁺ is dehydrated and migrates through the ditrigonal cavity in montmorillonite (Hofmann-Klemen effect; Fig. 5), however, the interlayer is fixed permanently, prohibiting rehydration (Derkowski & Kuligiewicz, Reference Derkowski and Kuligiewicz2017; Komadel et al., Reference Komadel, Hrobáriková and Koppelhuber-Bitschnau2002). A similar effect occurs even if the interlayer cations do not migrate into the 2:1 layer: if layer charge is located in the octahedral sheet, dehydrated interlayer cations are bonded strongly to the 2:1 layer, resulting in rehydration slower than if the charge came from tetrahedral cation substitution (Kawano & Tomita, Reference Kawano and Tomita1991a,Reference Kawano and Tomitab).

Fig. 6

Rehydration of a smectite reference sample (SWy-3), saturated with cations of contrasting hydration enthalpy, at various temperatures, after prior in situ drying for 4 h at 200°C. Mass gain is shown as fractional mass gain at a constant H₂O content of 9 g/kg air (not constant RH), normalized to the sample mass after drying at 200°C

Rehydroxylation occurs mostly in the intact dehydroxylated phase that preserves the layer structure and can undergo the reverse of the Eq. 1 reaction (Derkowski et al., Reference Derkowski, Drits and McCarty2012a). Once smectite crystallites reach the high-temperature amorphization or recrystallization, the structural integrity is lost. Therefore, dehydroxylated trioctahedral smectite, Mg-rich montmorillonite, and nontronite do not have great potential for rehydroxylation, whereas beidellite is the most prone to rehydroxylation because its layer structure remains intact at high temperatures (Derkowski et al., Reference Derkowski, Drits and McCarty2012a).

Because dehydroxylation of originally tv and cv aluminum smectites produces a similar tv phase, when rehydroxylated it resembles a tv structure (Drits et al., Reference Drits, Besson and Muller1995; Muller et al., Reference Muller, Drits, Plançon and Besson2000a, Reference Muller, Drits, Plançon and Robertb). Indeed, when analyzed with thermal methods, such a rehydroxylated phase dehydroxylates at the temperature range typical for tv beidellite (<500°C; irrespective of the temperature of dehydroxylation of its pristine structure (Derkowski & Kuligiewicz, Reference Derkowski and Kuligiewicz2017; Fig. 7). A tv Fe,Mg-rich smectite that adopts a cv character after dehydroxylation can probably return to tv when rehydroxylated (Drits & Zviagina, Reference Drits and Zviagina2009; Muller et al., Reference Muller, Drits, Plançon and Robert2000b). The most intense rehydroxylation occurs under H₂O vapor at temperatures of 250–350°C, even at extremely low H₂O activity. At such conditions, up to tens of % of the dehydroxylated dioctahedral smectite structure can be rehydroxylated within an hour of reaction (Fig. 7; Derkowski & Kuligiewicz, Reference Derkowski and Kuligiewicz2017). The mass gain observed during isothermal treatment of the prior dehydroxylated phase has been proven to correspond to true rehydroxylation by XRD and infrared spectroscopy (Kawano & Tomita, Reference Kawano and Tomita1989, Reference Kawano and Tomita1991b; Muller et al., Reference Muller, Drits, Plançon and Robert2000b; Derkowski et al., Reference Derkowski, Drits and McCarty2012a; Derkowski & Kuligiewicz, Reference Derkowski and Kuligiewicz2017). At reaction temperatures providing intense rehydroxylation, the interlayer’s H₂O diffusion does not result in permanent rehydration (Derkowski et al., Reference Derkowski, Drits and McCarty2012b).

Fig. 7

An example of an in-situ experiment of an isothermal rehydroxylation reaction observed with TGA (after Derkowski & Kuligiewicz, Reference Derkowski and Kuligiewicz2017) on a Cs⁺-exchanged beidellite (SBId-1) and montmorillonite (SWy-2). Note the initial dehydroxylation to 800°C under dry gas and switching to H₂O-rich gas for isothermal rehydroxylation, then secondary dehydroxylation to 1000°C under dry gas. The mass gain under wet gas corresponds to the rebuilding of OH groups

Rehydroxylation is site-specific and is influenced by several factors. If the layer charge is located in the tetrahedral sheet, the opening of the interlayer space during rehydroxylation is relatively easy due to large electrostatic repulsion between adjacent layers. Interlayer cation type also affects the rehydroxylation behavior of a smectite (Kawano & Tomita, Reference Kawano and Tomita1989, Reference Kawano and Tomita1991b; Emmerich et al., Reference Emmerich, Plötze and Kahr2001; Derkowski et al., Reference Derkowski, Drits and McCarty2012a; Derkowski & Kuligiewicz, Reference Derkowski and Kuligiewicz2017). Interlayer cations with relatively large radii (>0.13 nm in the eight-fold coordination; Shannon, Reference Shannon1976) act as pillars, which leads to a relatively large interlayer space of the dehydroxylate and enhances its rehydroxylation potential. Cations with large hydration potential also increase H₂O migration in the interlayer region, which is the prerequisite for further H₂O migration into the octahedral sheet and reformation of OH groups (Derkowski et al., Reference Derkowski, Drits and McCarty2012a,Reference Derkowski, Drits and McCartyb). If an anhydrous cation has a small ionic radius (< 0.08 nm, Li⁺, Mg²⁺), it can migrate into a pseudohexagonal cavity or into a vacant position of the former octahedral sheet and physically block access to the residual oxygen, which results in a reduced ability to rehydroxylate. Such cation migration results in irreversible collapse of the interlayer space (Emmerich, Reference Emmerich2000; Emmerich et al., Reference Emmerich, Plötze and Kahr2001; Derkowski et al., Reference Derkowski, Drits and McCarty2012a). In practice, rehydroxylation in smectites is controlled by the fraction of AlAlOH environment in the octahedral sheet, with no Al substitution in the neighboring tetrahedral sites (“pyrophyllite-like” domains), resulting in the lack of charge-compensating interlayer cations blocking the ditrigonal cavity for H₂O migration. Another factor is the valence of the exchangeable cation – the greater the valence, the fewer cations are present in the interlayer space and the lower the chance of blocking the pathway of potential rehydroxylation (Derkowski et al., Reference Derkowski, Drits and McCarty2012a).

Carrier Gas Composition and Pressure

Smectite thermal analysis is usually performed under dry gas purge in order to remove the products of dehydroxylation or dehydration. The presence of water vapor in the ambient gas changes the reaction pattern, shifting the reaction to higher temperatures following the H₂O content in the purge gas (Emmerich et al. Reference Emmerich, Steudel and Merz2017; Koster van Groos & Guggenheim, Reference Koster van Groos and Guggenheim1987, Reference Koster van Groos and Guggenheim1989; Levy & Hurst, Reference Levy and Hurst1993). Smectite dehydration and dehydroxylation reactions under high H₂O activity and high pressure were the subject of dedicated experiments enabling the prediction of smectite behavior under conditions relevant to geologic systems (Koster van Groos & Guggenheim, Reference Koster van Groos, Guggenheim, Stucki, Bish and Mumpton1990, and references therein). Vacuum conditions decrease the smectite reaction temperatures with respect to ≥1 bar conditions (Wicks & Ramik, Reference Wicks, Ramik, Stucki, Bish and Mumpton1990).

An analysis of redox-sensitive minerals requires use of a virtually oxygen-free purge gas (Bottom, Reference Bottom and Gabbott2008, Bish & Duffy, Reference Bish, Duffy, Stucki, Bish and Mumpton1990). The presence of oxygen in the purge gas can be tested in such cases using CuC₂O₄ (Lempart et al., Reference Lempart, Derkowski, Luberda-Durnaś, Skiba and Błachowski2018). The purge gas is considered virtually oxygen-free if no mass gain is detected during the experiment with pure CuC₂O₄.

Sample Form and Packing

With some exceptions, smectite samples are typically analyzed in a powder form. Before a thermal experiment, powdered samples should be homogenized and preferably sifted through a 100 or 200 μm mesh sieve, which allows for the reduction of the size of smectite aggregates present in the sample. In the case of montmorillonite that has a temperature of amorphization close to that of dehydroxylation, the presence of large aggregates leads to the formation of macroscopic bubbles and hollow spheres, especially for samples with exchangeable cations of high hydration enthalpy, such as Ca²⁺, Mg²⁺, or Li⁺ (Fig. 8; Emmerich, Reference Emmerich and Christidis2010; Emmerich et al., Reference Emmerich, Steudel and Merz2017). The spheres are probably produced by slow heat transfer inward and slow diffusion of H₂O outward from the aggregates. Interestingly, the formation of such spheres has virtually no effect on the DTG curve or mass loss during a TG experiment (Fig. 8).

Fig. 8

The texture (upper) and DTG pattern (lower) of unsifted and sifted Ca²⁺-exchanged montmorillonite sample (SCa-3) after heating to >1000°C at a constant rate of 20°C/min (DTG pattern) and 500°C/min under a flow of 50 mL/min dry N₂ gas

The way powder is loaded into a holder can also affect the reaction temperature (Emmerich, Reference Emmerich and Christidis2010); a pressed sample delays the diffusion of the reaction volatile products out of the holder due to decreased permeability. Although the effect is not greater than a few °C, and thus is within the temperature error (Schilling, Reference Schilling1990), use of a loose powder or exactly the same mode of pressing for all samples being compared is recommended. Also, the experiments involving surface reaction with ambient gas (i.e. dehydrogenation under oxidizing conditions) may be strongly affected by the sample permeability to gases.

The maximum reaction temperature correlates positively with the sample mass due to the heat capacity and the diffusion rate of volatile reaction products (Schilling, Reference Schilling1990; Wolters & Emmerich, Reference Wolters and Emmerich2007). However, as found by Derkowski and Kuligiewicz (unpublished data), up to 20% relative of smectite sample weight difference has a negligible effect on the reaction temperature and remains within the analytical error; 20% would thus be the maximum difference in the sample weights recommended for relative comparison. The greater the sample weight, the lower the relative influence of total measurement errors (weighing imprecision, thermal drift) that are usually expressed in absolute quantities, i.e. are independent of the sample size. However, upon heating, a smectite sample can change its bulk volume (due to recrystallization, amorphization) or electrostatic properties (due to dehydration, cation fixation), resulting in the holder overflow and the drop of a sample portion off the holder, which is detrimental to the analysis. Fortunately, a material drop is usually abrupt enough to be distinguishable from a slower thermal reaction of smectites, allowing the results to be rejected from interpretation. Such a sample drop is typical for Li⁺-montmorillonites at the temperature of dehydroxylation, when a sample is blown off the holder by purge gas (Fig. 9). Using a holder with a lid may prevent that problem (e.g. Emmerich et al., Reference Emmerich, Steudel and Merz2017; Wolters & Emmerich, Reference Wolters and Emmerich2007), but this would also induce a delay in removal of volatiles from the sample. The delayed removal of the reaction products by the gas purge results in momentary production of a water vapor atmosphere around the sample.

Fig. 9

TGA patterns of Li⁺- and Ca²⁺-exchanged montmorillonite (SWy-2) heated isothermally for 4 h at temperatures as indicated in the legend followed by ramp-heating at 10°C/min under a flow of 50 mL/min of dry N₂. Note the abrupt mass loss at almost the same temperature in Li⁺-exchanged samples, originating from the sample dropping off the holder

Factors Affecting Evolved Gas Analysis (EGA)

Isothermal reactions are usually not recorded in EGA. The EGA requires a high heating rate and high carrier gas flow, unless a vacuum system is used (Wicks & Ramik, Reference Wicks, Ramik, Stucki, Bish and Mumpton1990 cf. Lempart et al., Reference Lempart, Derkowski, Strączek and Kapusta2020). High heating rates (and possibly large sample masses) are usually needed to keep the evolved gas in a concentration range that is easily determined by the applied spectrometric method.

In the MS signal, H₂O is represented by four spectral masses, the dominant m/z = 18, and the minor m/z = 17 (OH⁺), whereas, the H₃O⁺ (m/z = 19) and O⁺ (m/z = 16) can be detected in orders of magnitude lower intensity (Meija et al., Reference Meija, Mester and D'Ulivo2006; Emmerich, Reference Emmerich and Christidis2010). With pure dehydration and dehydroxylation reactions, the m/z 17 follows precisely m/z 18, and both signals overlap the DTG curve (Fig. 1). The NH₃ evolution from NH₄ ⁺-smectites would produce excess m/z 17 whereas dehydrogenation under O₂ (or air) would produce an additional H₂O signal distinguishable as an excess to the DTG curve (Heller-Kallai, Reference Heller-Kallai1997b, Fig. 5 in Lempart et al., Reference Lempart, Derkowski, Strączek and Kapusta2020; Fig. 1). Dehydrogenation that produces H₂ (m/z = 2) is difficult to detect and requires a fast sample-heating rate (≥20°C/min; Lempart et al., Reference Lempart, Derkowski, Strączek and Kapusta2020) in MS or employing a GC–MS system.

Halogen elements present in trioctahedral smectites substituting OH groups (mostly F, also Cl, B) evolve from a smectite sample as hydrogen halides or radicals forming gaseous diatomic molecules (Heller-Kallai, Reference Heller-Kallai1997b; Wicks & Ramik, Reference Wicks, Ramik, Stucki, Bish and Mumpton1990). Strong reactivity of H-halide molecules with metals makes them react with any metal-based elements of the analyzer setup, however, and so ceramic pans and skimmer TGA-MS interfaces are suggested.

Impurities

The mass loss recorded with TGA in a pure smectite should correspond to the cation-dependent dehydration and the theoretical mass loss corresponding to dehydroxylation (Emmerich, Reference Emmerich and Christidis2010; Kuligiewicz & Derkowski, Reference Kuligiewicz and Derkowski2017). In nature, smectite never occurs as a pure mineral, even in bentonite beds. Also, even a thorough chemical treatment aimed at removing impurities and grain-size fractionation (Jackson, Reference Jackson1969), usually leaves some impurity in the studied smectite fraction. Some impurities are not reactive in the temperature range corresponding to major smectite reactions, e.g. the presence of quartz and feldspar only reduces the theoretical mass loss due to dehydroxylation. Other impurities, however, have their own thermal reactions that can strongly affect the thermal analysis pattern of smectite samples (Emmerich, Reference Emmerich and Christidis2010). The presence of discrete or interstratified kaolinite frequently coexisting with aluminous smectites (such as beidellites), increases the sample’s mass loss in the dehydroxylation range, as kaolinite has three times more OH groups per formula unit to form H₂O than smectite. The above-mentioned impurities can be detected by XRD and for kaolinite also by infrared spectroscopy.

During smectite cation exchange with divalent cations, atmospheric CO₂ dissolved in the exchange solution binds with the cations forming carbonate impurities. In TGA tests they provide a significant mass loss corresponding to 44–52% of the carbonate content depending on the type of carbonate; the same mass loss would come from naturally occurring carbonate minerals present in a clayey sample (Emmerich & Smykatz-Kloss, Reference Emmerich and Smykatz-Kloss2002; Emmerich, Reference Emmerich and Christidis2010), if they were not carefully removed during the chemical pretreatment (Jackson, Reference Jackson1969). Therefore, even minute quantities of carbonate minerals, untraceable using other methods (e.g. XRD), can affect the smectite mass-loss determination. Thermal decarbonatization resulting in CO₂ evolved usually at temperatures of 700–900°C can be observed with EGA, however, e.g. by monitoring m/z = 44 in the TGA-MS setup (Fig. 1), in order to apply appropriate mass-loss corrections.

Sedimentary or soil organic matter (SOM) can be bound strongly to smectite surfaces and is difficult to remove even by extensive chemical treatment (Mikutta et al., Reference Mikutta, Kleber, Kaiser and Jahn2005; Szymański et al., Reference Szymański, Drewnik, Stolarczyk, Musielok, Gus-Stolarczyk and Skiba2022). Thermal decomposition of recalcitrant SOM under neutral gas results in various evolved molecules, usually below 500°C, identifiable by EGA-MS as a series of various signals with m/z > 50 (Emmerich, Reference Emmerich and Christidis2010), along with those belonging to hydrocarbons (methane with m/z = 16), and CO₂ (m/z = 44; Fig. 1). The SOM-evolved H₂O (m/z = 18) and NH₃ (m/z = 17) overlap with the smectite-derived H₂O signal. Under neutral gas, only a portion of SOM decomposes, leaving charcoal as a high-temperature product. If run under oxidizing gas (i.e. air), SOM oxidizes completely, usually below 400°C, resulting in evolved H₂O and CO₂ identifiable by EGA, and the excess mass loss equal the SOM content. The difference in mass loss and evolved gas composition (especially CO₂) between the experiments under neutral and oxidizing gas can reveal the SOM presence. However, structural Fe(II) present in the smectite or associated phases can decrease mass loss under oxidizing conditions, canceling the SOM effect, leaving CO₂ (m/z = 44) as the most reliable proxy.

Hydrous sulfate minerals (e.g. gypsum) are the first to be removed during smectite sample pretreatment. However, if present in a sample even in minute amounts, their mass loss upon dehydration at 100–200°C (for example, 21% in gypsum) increases smectite dehydration. Desulfurization occurring at >700°C – in the range of trioctahedral smectite dehydroxylation – results in a loss of almost 50% of gypsum mass, which can be detected easily using EGA-MS (m/z: 64, 48, 32; Emmerich, Reference Emmerich and Christidis2010; Dietel et al., Reference Dietel, Warr, Bertmer, Steudel, Grathoff and Emmerich2017). If analyzed under oxidizing conditions, trace sulfides, e.g. pyrite, reacting with O₂ also release SO₂ albeit at lower temperatures (<500°C; Dietel et al., Reference Dietel, Warr, Bertmer, Steudel, Grathoff and Emmerich2017). When reacting with H₂O coming from a smectite’s dehydroxylation at 500–800°C, sulfides produce H₂S molecules (Levy & White, Reference Levy and White1988).

Theoretical Background

As in any other reaction, de- and re-hydration and de- and re-hydroxylation can be tracked using common kinetic approaches. The comprehensive review of methodology applicable in solid-state kinetics studies of thermally stimulated processes can be found elsewhere (e.g. Khawam & Flanagan, Reference Khawam and Flanagan2006a,Reference Khawam and Flanaganb; Vyazovkin et al., Reference Vyazovkin, Burnham, Criado, Pérez-Maqueda, Popescu and Sbirrazzuoli2011, Reference Vyazovkin, Burnham, Favergeon, Koga, Moukhina, Pérez-Maqueda and Sbirrazzuoli2020). A brief introduction of the key methodological points is presented below, with special emphasis on methods applicable to the thermal reactions of smectite.

The majority of methods in solid-state kinetic analysis of thermally stimulated reactions are based on the following equation:

(5) $\frac{d\alpha }{dt}=k\left(T\right)f\left(\alpha \right)$

which states that the reaction rate (dα/dt) is dependent on the absolute temperature (in K) through the reaction rate constant (k(T)) and on the extent of conversion (α) through the reaction mechanism (f(α)). The extent of conversion is the dimensionless parameter describing progress of the reaction and is scaled between 0 and 1, where 0 corresponds to the start and 1 to the completion of the reaction. The extent of conversion must correspond to a change of some measurable property of a material that represents the reaction progress. In TGA practice, this parameter is mass change and α is expressed conveniently as the ratio of mass change at a given time during the reaction to the mass change corresponding to the completion of the reaction e.g. to full dehydroxylation. Calculating the reaction progress from DTA and DSC data requires prior integration of the peak over time or temperature. The reaction mechanism in Eq. 5 is a function describing the progress of a reaction based on the molecular reaction mechanism and/or reactant geometry and can take various mathematical forms (Khawam & Flanagan, Reference Khawam and Flanagan2006a,Reference Khawam and Flanaganb; Vyazovkin et al., Reference Vyazovkin, Burnham, Criado, Pérez-Maqueda, Popescu and Sbirrazzuoli2011). The dependence of the reaction rate constant on temperature is most commonly expressed with the Arrhenius equation:

(6) $k\left(T\right)=A\exp \left(\frac{{-E}_a}{RT}\right)$

where A is the pre-exponential factor, E _a is the activation energy, and R is the gas constant.

Substituting Eq. 6 into Eq. 5 gives:

(7) $\frac{d\alpha }{dt}=A\exp \left(-,\frac{E_a}{RT}\right)f\left(\alpha \right)$

or in the logarithmic form:

(8) $\ln \left(\frac{d\alpha }{dt}\right)=\ln A+\ln \left(f,\left(\alpha \right)\right)-\frac{E_a}{RT}$

Finding the triplet f(α), E _a, and A allows for the full kinetic description of the reaction studied. However, many kinetic studies present only an estimation of E _a as the most relevant reaction-specific parameter. Depending on the mode in which the thermal analysis experiment was performed, E _a can be calculated using isothermal or non-isothermal data, the latter most commonly coming from linear heating experiments (Fig. 10). In any case, using at least three temperature programs is strongly advised (Vyazovkin et al., Reference Vyazovkin, Burnham, Criado, Pérez-Maqueda, Popescu and Sbirrazzuoli2011; Figs. 10, 11b), and at least five points are required to detect any non-Arrhenius behavior of the reaction, which manifests itself by non-linearity of Eqs. 6 and 8 (Vyazovkin et al., Reference Vyazovkin, Burnham, Favergeon, Koga, Moukhina, Pérez-Maqueda and Sbirrazzuoli2020).

Fig. 10

The examples of linear, ramp-heating of a Na⁺-beidellite sample to 1000°C under a 50 mL/min flow of dry N₂ and at various heating rates. The rates are indicated at the DTG peak in °C/min. The shift between the DTG_max peaks can be used to determine the activation energy of dehydroxylation

Fig. 11

A, C–F Activation energy (E _a) of the dehydroxylation of various dioctahedral smectites, calculated using the 0.01 α-increments and the Friedman method, and B an example of E _a determination using the Kissinger method and the DTG peak temperature (Fig. 10). Note the similarity of the E _a values and trends in the dehydroxylation of two Ca²⁺-exchanged Mg-rich montmorillonites (E, F). For each TGA run, the total mass loss upon dehydroxylation was divided into 100 portions of equal mass difference (0.01α). For each 0.01α, the ln(dα/dt) was plotted against the corresponding 1/T using four or five data points from the TGA curves recorded with a different heating rate (B). E E _a is then calculated from the slope of ln(dα/dt) vs 1/T plot (Eq. 8). The correlation coefficient, R², was computed for each of 0.01α. All E _a values shown (A, C–F) are reported for R² > 0.997 (arbitrary cut-off),

Two general types of kinetic calculations are used for thermal analysis data. The model-fitting approach is based on fitting one of the reaction models available in the literature to Eq. 5 or its integral form and finding the best-fitting model, simply by comparing its linearity with experimental data. The reaction mechanism may or may not include adjustable parameters, which can later be interpreted in terms of a rate-controlling model (Bray & Redfern, Reference Bray and Redfern2000; Giese, Reference Giese, Stucki, Bish and Mumpton1990; Vyazovkin et al., Reference Vyazovkin, Burnham, Criado, Pérez-Maqueda, Popescu and Sbirrazzuoli2011). In smectites, the isothermal model-fitting approach has been proved useful for determining the kinetics of dehydration (Bray & Redfern, Reference Bray and Redfern1999), dehydroxylation (Bray & Redfern, Reference Bray and Redfern2000), and rehydroxylation (Derkowski & Kuligiewicz, Reference Derkowski and Kuligiewicz2017).

The second type of calculations are those using the isoconversional methods (Criado et al., Reference Criado, Sánchez-Jiménez and Pérez-Maqueda2008, Perez-Rodriguez et al., Reference Perez-Rodriguez, Duran, Sanchez Jimenez, Franquelo, Perejón, Pascual-Cosp and Pérez-Maqueda2010; Vyazovkin, Reference Vyazovkin2015, Vyazovkin, Reference Vyazovkin2021), in which E _a and A are calculated without any assumptions of a particular kinetic model or the reaction order. The basic principle behind the isoconversional methods is that the value of f(α) in Eq. 5 is independent of T. In other words, the value of f(α) is constant for a given α, irrespective of the temperature program. In its simplest form for non-isothermal conditions (the Friedman method), calculating isoconversional E _a involves plotting the values of ln(dα/dt) against 1/T for a given α. The isoconversional approach enables changes in E _a to be detected during the reaction progress with no prior assumptions regarding the reaction mechanism. Such changes can, for example, reflect the changes in the bond strength with the reaction progress (Kuligiewicz & Derkowski, Reference Kuligiewicz and Derkowski2017).

Another calculation method based on the isoconversional principle and representing its simplified version is the method of Kissinger (Reference Kissinger1957). It is applicable to linear heating conditions and is based on the shift of the reaction peak when changing the heating rate, thus directly applicable to DTA, DSC, and DTG data (Fig. 10). This method employs the fact that for the maximum reaction rate (DTG peak), d²α/dt ² = 0. Taking this into account, the Kissinger equation can be derived from Eq. 7:

(9) $\ln \left(\frac{\beta }{T^2}\right)=\ln \left(-,\frac{AR}{E_a},\frac{df\left(\alpha \right)}{d\alpha }\right)-\frac{E_a}{R}\frac{1}{T}$

where β is the linear heating rate (dT/dt). Values of all other parameters (T, f(α), and α) in Eq. 9 refer to values at the maximum reaction rate. In practice, the left side of Eq. 9 is plotted against 1/T, which should produce a straight line, the slope of which can be used to calculate E _a (i.e.Vyazovkin, Reference Vyazovkin, Burnham, Criado, Pérez-Maqueda, Popescu and Sbirrazzuoli2011; Fig. 11b).

Note that some studies apply kinetics analysis to data obtained from a single temperature program only (i.e. only one isothermal heating temperature or only one linear heating rate), which is especially common in the older literature. While this approach was justifiable because of hardware and computational limitations in those times, it is now generally considered unreliable (Vyazovkin et al., Reference Vyazovkin, Burnham, Criado, Pérez-Maqueda, Popescu and Sbirrazzuoli2011).

Kinetics of Smectite Thermal Reactions

Dehydration

Despite the large number of studies of smectite–water interactions, kinetics studies of smectite dehydration employing thermal analysis methods do not present a consistent picture. Besides the dependence of dehydration energy on the hydration enthalpy of the interlayer cations (Webb et al., Reference Webb, Stanley and Scheiner1986), it has been demonstrated that a change occurs in the reaction mechanism along the course of dehydration (Koster van Groos & Guggenhem, Reference Koster van Groos, Guggenheim, Stucki, Bish and Mumpton1990; Bray & Redfern, Reference Bray and Redfern1999; Kuligiewicz & Derkowski, Reference Kuligiewicz and Derkowski2017; Poinsignon et al., Reference Poinsignon, Yvon and Mercier1982; Zabat & Van Damme, Reference Zabat and Van Damme2000). As already mentioned, physisorbed water in the micro- and mesopores and bulk interlayer water represent the ‘weakly-bound water’ (WBW). WBW is removed preferentially during dehydration because of its weaker interactions with the smectite surface. Change in the reaction mechanism during dehydration and the associated change in E _a (Table 2) correspond to the completion of weakly bound water removal and the onset of strongly bound water removal. The E _a of dehydration of WBW is in the range 35–79 kJ/mol for smectites having monovalent and divalent interlayer cations commonly found in nature (Ca²⁺, Mg²⁺, K⁺, Na⁺, Li⁺; Table 2). As deduced from Table 2, E _a of WBW dehydration in general does not depend on the exchangeable cation type or chemistry of the 2:1 layer. Once weakly bound water is removed, removal of the sequential portions of strongly bound water requires increasingly higher energy, as is manifested by the continuous increase in E _a with reaction progress, up to 190 kJ/mol (Kuligiewicz & Derkowski, Reference Kuligiewicz and Derkowski2017). This was interpreted as the result of bond reconfiguration upon removal of water molecules from hydration spheres of interlayer cations, in agreement with theoretical calculations (Pavlov et al., Reference Pavlov, Siegbahn and Sandström1998).

Table 2

Comparison of the E _a of dehydration of weakly bound water (WBW) and strongly bound water (SBW) from studies employing various methods

^*Zabat and Van Damme (Reference Zabat and Van Damme2000) assumed the first-order reaction mechanism for dehydration and presented a new computation method, using principles similar to those of the Kissinger method

Dehydroxylation

In the majority of dioctahedral smectites studied, E _a of dehydroxylation does not vary much with the reaction progress (Fig. 11A,C,D). If the initial (α < 0.2) and final (α > 0.8) portions of the data, corresponding also to lower R² coefficients because of an overlap with other thermal effects are excluded, the E _a values remain similar over a broad range of α for beidellite SBId-1, cv beidellitic montmorillonite SWy-1, and ferruginous smectite SWa-1 (an approximation for nontronite) (Fig. 11). In Mg-rich montmorillonites that have charge generated exclusively in the octahedral sheet, however, E _a increases significantly with α, especially in the samples saturated with divalent cations (Fig. 11E,F). The increase of E _a in montmorillonite remains in line with the interpretation of Koster van Groos and Guggenheim (Reference Koster van Groos and Guggenheim1989) who suggested the increase in the residual OH bond strength upon sequential removal of OH groups in heterogeneous structure.

The kinetics of smectite dehydroxylation is controlled by the same structural factors as the temperature of dehydroxylation (Figs. 1 and 3). Activation energy of dehydroxylation as computed from linear heating experiments with isoconversional methods correlates linearly with the temperature of maximum dehydroxylation, based on the DTG peak (Fig. 12, Table 3). The observed relationship implies that the rate-controlling mechanism of dehydroxylation is the same in all smectites regardless of their crystal-chemical composition.

Fig. 12

The E _a of dehydroxylation of smectite reference samples presenting values averaged over α = 0.2–0.8 calculated using the Friedman method (upper, cf. Figure 11) and E _a calculated using the conventional Kissinger method based on DTG peak temperature (lower, cf. Fig. 10), plotted against the maximum of dehydroxylation (DTG_max; Table 3). The E _a error in the Kissinger method is ~5%. Filled shapes denote the Cs⁺-exchanged form; note their lower position with respect to other cations

Table 3

E _a of dehydroxylation calculated as using the 0.01 α-increments with values averaged over α = 0.2–0.6 calculated using the Friedman method (Fig. 11) and E _a calculated using the conventional Kissinger method based on DTG peak temperature (Fig. 10). The maximum of dehydroxylation (DTG_max) was determined using the 5°C/min constant rate TG measurement

^*estimated E _a error in the Kissinger method is ~ 5% relative

Another factor influencing the kinetics of smectite dehydroxylation is the interlayer cation type. The application of the model-fitting approach to isothermal data allowed demonstration that the interlayer cation type can modify the dominant reaction model, which provides the best description of the process. Bray and Redfern (Reference Bray and Redfern2000) suggested that dehydroxylation in smectite saturated with divalent cations (Ca²⁺ or Mg²⁺) is diffusion-controlled, while dehydroxylation in smectites saturated with monovalent cations (Na⁺ or K⁺) follows the first-order reaction kinetics. The influence of the interlayer cation on the dehydroxylation E _a value is less clear (Bray & Redfern, Reference Bray and Redfern2000; Kuligiewicz & Derkowski, Reference Kuligiewicz and Derkowski2017) but it seems that Mg²⁺-exchanged smectites have significantly lower E _a values than Ca²⁺- or Na⁺-exchanged counterparts (Bray & Redfern, Reference Bray and Redfern2000; Kuligiewicz & Derkowski, Reference Kuligiewicz and Derkowski2017). A speculative explanation may be that Mg²⁺, which is capable of retaining dissociated H₂O (Mg-OH) up to temperatures of dehydroxylation, acts as a flux and lowers the E _a of dehydroxylation.

All of the above-mentioned results and interpretations come from studies using simple (isothermal or linear heating rate) thermal experiments. An alternative approach based on multiple heating–cooling cycles was employed by Drits et al. (Reference Drits, Derkowski and McCarty2012a) to determine the kinetics of partial dehydroxylation in dioctahedral smectites and other 2:1 layer minerals. The protocol involves heating the samples with a constant heating rate and subsequent cooling by increasing each following cycle’s maximum temperature in small increments (i.e. 25°C). If a temperature increment between cycles is sufficiently small, the increase of α within one and the same cycle is negligible; therefore, α can be considered as constant for the cycle, meeting the requirement of the isoconversional kinetic approach. Within the cycle, the majority of the ln(dα/dt) over 1/T returns a linear fit, which Drits et al. (Reference Drits, Derkowski and McCarty2012a) interpreted as the zeroth-order kinetics of partial dehydroxylation. Such a heating–cooling cycle approach apparently allows tracking of E _a in different stages of the reaction or portions of sample reacted at subsequently higher temperatures. However, for a portion of the sample reacting with constant f(α), the Arrhenius relationship represents the population that has already been treated thermally in the preceding cycle, hence, not corresponding to the actual rate-controlling mechanism in full reaction (Muñoz-Santiburcio et al., Reference Muñoz-Santiburcio, Kosa, Hernández-Laguna, Sainz-Díaz and Parrinello2012; Ogloza & Malhotra, Reference Ogloza and Malhotra1989). The difficulty in explaining the concave shape of E _a evolution over α (Fig. 13) and the maximum E _a being much lower than that for full reaction (Figs. 11 and 12) implies the limited use of the heating–cooling protocol and the need for specific interpretation of the kinetic data.

Fig. 13

An example of the calculation of E _a of smectite dehydroxylation for Ca²⁺-saturated SCa-3 montmorillonite based on a heating–cooling cycles TGA experiment (Drits et al., Reference Drits, Derkowski and McCarty2012a). The maximum temperature (in °C) of each consecutive heating cycle is given in italics. Compare E _a values with Fig. 11e