1. Introduction

Al_xGa_1-xN alloys, with a bandgap tunable from 365 nm (x=0) to 200 nm (x=1), are extremely attractive for optoelectronic applications such as visible-blind ultraviolet (UV) photodetectors Reference Razeghi and Rogalski[1]. These materials are remarkably tolerant to aggressive environments, due to its thermal stability and radiation hardness. Applications range from flame detection to space communications or solar UV monitoring systems Reference Monroy, Calle, Angulo, Vila, Sanz, Garrido, Muñoz, Calleja, Beaumont, Omnès and Gibart[2].

High responsivity Al_xGa_1-xN photoconductors have already been demonstrated Reference Lim, Chen, Yang and Asif Khan[3] Reference Walker, Zhang, Saxler, Kung, Xu and Razeghi[4] Reference Monroy, Calle, Garrido, Youinou, Muñoz, Omnès, Beaumont and Gibart[5]. However, the persistent photoconductivity (PPC) Reference Monroy, Calle, Garrido, Youinou, Muñoz, Omnès, Beaumont and Gibart[5] Reference Monroy, Garrido, Muñoz, Izpura, Sánchez, Sánchez-García, Calleja, Beaumont and Gibart[6] present in these devices results in a very slow non-exponential response which makes them unsuitable for most applications. GaN photovoltaic diodes have proven to be a better approach than photoconductive devices in applications requiring fast response or a high UV/visible contrast Reference Monroy, Calle, Angulo, Vila, Sanz, Garrido, Muñoz, Calleja, Beaumont, Omnès and Gibart[2] Reference Monroy, Muñoz, Sánchez, Calle, Calleja, Haffouz, Beaumont and Gibart[7]. Schottky barrier GaN photodetectors were first reported by Khan et al. Reference Asif Khan, Kuznia, Olson, Blasingame and Bhattarai[8], who demonstrated a Ti Schottky diode on p-type GaN. This devices showed a RC-limited time response of 1 μs (time for the signal to fall from maximum to 1/e), and a zero-bias responsivity of 130 mA/W illuminating through the sapphire. The inconvenience of backside illumination was analyzed by Binet et al. Reference Binet, Duboz, Laurent, Rosencher, Briot and Aulombard[9], who calculated a hole diffusion length of 0.1 μm which limited the device response. This problem was overcome by a semitransparent Schottky electrode, as used by Chen et al Reference Chen, Yang, Osinsky, Gangopadhyay, Lim, Anwar, Khan, Kuksenkov and Temkin[10], who reported a 50 Å Pd Schottky barrier on n-type GaN, with a responsivity of 180 mA/W and a RC-limited time response of 118 ns on a 50 Ω resistance. Al_0.26Ga_0.74N photodiodes based on 50 Å Pd Schottky barriers have been recently demonstrated Reference Osinsky, Gangopadhyay, Lim, Anwar, Khan, Kuksenkov and Tempkin[11], showing a responsivity of 70 mA/W with a minimum time response of 1.6 μs. In this work, we report on the fabrication and characterization of Schottky barrier photovoltaic detectors based on Si-doped Al_xGa_1-xN samples with different Al content (0 ≤ × ≤ 0.22), aiming to increase the time response.

2. Devices and experimental

The Al_xGa_1-xN epilayers were grown on basal plane sapphire in an AIX200RF horizontal LP-MOVPE reactor. Trimethylgallium (TMG), trimethylaluminum (TMA) and ammonia (NH₃) served as precursors, and H₂ was used as carrier gas. Growth temperature was fixed at 1170°C, with a V/III partial ratio of 3500, and a growth rate of 1 μm/h. A 250 Å thick GaN buffer layer was grown at 525°C. N-type doping has been achieved using silane (SiH₄). The aluminum fraction in the solid phase was determined by energy dispersion spectroscopy (EDS) in a scanning electron microscope. AlGaN epilayers show a FWHM of 670 arc-sec for the (0002) X-ray double diffraction peak in the Ω-configuration Reference Omnes, Marenco, Haffouz, Lahreche, de Mierry, Beaumont, Hageman, Monroy, Calle and Muñoz[12]. Typical electron mobilities of 75−90 cm²/Vs and 140 cm²/Vs are obtained at room temperature in 2 × 10¹⁸ cm⁻³ n-type doped AlGaN and GaN respectively. Doping levels as determined by C-V measurements ranged from 5 × 10¹⁷ cm⁻³ to 2 × 10¹⁸ cm⁻³.

For the fabrication of Schottky barriers, samples were diced into 4 × 4 mm squares and cleaned in acids. A semitransparent 100Å thick Au layer was deposited by Joule evaporation. The transmittance of this layer was found to be rather flat in the ultraviolet region, with a mean value of 30%. The pattern of the metallization was defined with standard photolithography. Detector diameters ranged from ϕ = 240 μm to ϕ = 1 mm. A second metallization was performed to deposit a gold pad, whose pattern was defined using a lift-off technique. Ohmic contacts were made with indium.

The photodiode current-voltage (I-V) characteristics were measured with a Hewlett Packard HP4155A semiconductor parameter analyzer. Capacitance vs. bias voltage were obtained using a Hewlett Packard HP4284A LCR-meter. Photodetector responsivity and its dependence on the incident optical power were determined with a non-focused cw He-Cd laser (325 nm). Spectral responsivity studies were performed by using a 150W xenon arc lamp and a Jobin-Yvon H−25 monochromator with a holographic grating that ensures good transmission down to 200 nm. The optical system was calibrated using a Molectron PR200 pyroelectric detector. Time response was measured using the fourth frequency of a Nd-YAG laser (266 nm), whose pulses were gaussian with a FWHM of 10 ns. Low frequency noise studies were performed with a PARC 113 low noise preamplifier and a FFT analyzer. The system has a background level of ~10⁻²¹ A²/Hz.

3. Results and discussion

Figure 12 shows a typical I-V curve of Al_0.22Ga_0.78N Schottky diodes. Devices present an ideality factor of 1 to 2, a leakage resistance above 500 MΩ, and a typical forward resistance of 100 Ω. Capacitance-voltage (C-V) characteristics are shown in the inset for diodes with different sizes. In GaN diodes a barrier height of about 1 eV is estimated from the C-V curve. However, in Al_xGa_1-xN higher values are obtained (~2 eV), probably due to the presence of oxide in the surface.

The room temperature spectral responsivity of the photodiodes is depicted in Figure 2. Photocurrent increases linearly with optical power from 10 mW/m² to 2 KW/m², as shown in the inset. Responsivity remains quite flat for photons with energy over the bandgap, with values of 70 mA/W, 45 mA/W and 29mA/W for Al_xGa_1-xN with × = 0, 0.15 and 0.22 respectively. These low values are due to the metal thickness (100 Å). A rejection of the visible radiation of more than three orders of magnitude is measured in all the devices, independent of diode size. The cutoff wavelength shifts with Al content from 362 nm (x = 0) to 320 nm (x = 0.22), which implies a linear variation of the energy bandgap as a function of aluminum concentration. This dependence has been checked by transmission measurements Reference Omnes, Marenco, Haffouz, Lahreche, de Mierry, Beaumont, Hageman, Monroy, Calle and Muñoz[12], and agrees with the data published by Wickenden et al. Reference Wickenden, Bargeron, Bryden, Miragliotta and Kistenmacher[13], although it is in contradiction with the downward bowing parameter recently reported by Brunner et al. Reference Brunner, Angerer, Bustarret, Freudenberg, Höpler, Dimitrov, Ambacher and Stutzmann[14].

Figure 1.

Current vs. voltage (I-V) characteristic of an Al_0.22Ga_0.78N/Au Schottky photodiode. In the inset, 1 / C² vs. voltage relation.

Figure 2.

Zero-bias spectral response of Al_xGa_1-xN Schottky photodetectors at room temperature. In the inset, variation of photocurrent with irradiance in a GaN Schottky diode.

Exponential photocurrent decays have been found when switching off the illumination, as shown in Figure 3 for Al_0.22Ga_0.78N diodes operating with a 2 KΩ load resistance. Detectors are RC limited, where R is the sum of the load resistance, R_L, and the series resistance of the device, R_S, and C is the sum of the load capacitance, C_L, and the capacitance related to the diode space-charge-region, C_SCR.

Figure 3.

Photocurrent decays observed in Al_0.22Ga_0.78N/Au Schottky photodiodes with different sizes and bias. Red dotted lines correspond to exponential fits.

The dependence of photocurrent decay time on the load resistance has been analyzed (see Figure 4) and confirms the RC behavior. By extrapolating the results in figure 3 to zero load resistance, a minimum time constant of 15 ns is estimated for 240 μm Al_0.22Ga_0.78N Schottky diodes. This value is shorter than the values previously reported for similar size AlGaN Schottky photodiodes Reference Osinsky, Gangopadhyay, Lim, Anwar, Khan, Kuksenkov and Tempkin[11]. The observed time response decreases with diode size due to the reduction of its internal capacitance. Time response is further reduced by reverse biasing, as diode capacitance decreases with the square root of the reverse bias voltage (see Figure 5).

Figure 4.

Photocurrent decay time constant vs. load resistance measured in Al_0.22Ga_0.78N/Au Schottky photodiodes with different sizes and bias voltage. Black dotted lines correspond to linear fits.

Figure 5.

Variation of diode capacitance with reverse bias. Dotted line represents the sum of the diode internal capacitance and the load capacitance, C_L. The decay time constant dependence on reverse bias (blue dots) is also shown.

The bandwidth of the devices, BW, can be estimated by:

For diodes with the same geometry and polarization, C_SCR and R_S are proportional to N_D ^1/2 and (μN_D)⁻¹ respectively, where μ is the electron mobility and N_D is the doping level. Therefore, the bandwidth of these devices would be optimized by increasing μN_D ^1/2. Under this assumption, Si-doping should improve the time response of Schottky photodiodes, provided that mobility does not decrease drastically and Schottky barrier is not much lowered by tunnel transport.

Low frequency noise is 1/f limited, satisfying the relationship:

where I_d is the dark current, and S₀ and γ are fitting parameters, with 1 ≤ γ ≤ 1.2. A noise equivalent power (NEP) of 13 nW has been obtained in ϕ = 1mm Al_0.22Ga_0.78N diodes at −1.35 V bias, which implies a normalized detectivity as high as 3.5 × 10⁷ Hz^1/2W⁻¹m.

4. Conclusions

Schottky barrier photovoltaic detectors have been fabricated on Si-doped Al_xGa_1-xN (0 ≤ × ≤ 0.22) samples grown on sapphire by MOVPE. Schottky contacts were made with Au. Responsivities are independent of the diode size and of the incident power in the range measured (10 mW/m² to 2 KW/m²). The spectral response shows an abrupt cutoff that shifts linearly to higher energy with increasing Al content. A visible rejection of 3 to 4 orders of magnitude is observed in Al_xGa_1-xN Schottky photodiodes. Device time response is RC-limited, and a minimum decay time as short as 15ns have been estimated in unbiased Al_0.22Ga_0.28N diodes. This time response can be further reduced by reverse biasing. Low frequency noise is 1/f limited, and detectivities as high as 3.5 × 10⁷ Hz^1/2W⁻¹m have been obtained in ϕ = 1mm Al_0.22Ga_0.78N diodes at −1.35 V.