Skip to main content
×
×
Home

Experimental analysis and thermodynamic calculations of an additively manufactured functionally graded material of V to Invar 36

  • Lourdes D. Bobbio (a1), Brandon Bocklund (a1), Richard Otis (a2), John Paul Borgonia (a2), Robert Peter Dillon (a2), Andrew A. Shapiro (a2), Bryan McEnerney (a2), Zi-Kui Liu (a1) and Allison M. Beese (a1)...
Abstract

Functionally graded materials (FGMs) in which the elemental composition intentionally varies with position can be fabricated using directed energy deposition additive manufacturing (AM). This work examines an FGM that is linearly graded from V to Invar 36 (64 wt% Fe, 36 wt% Ni). This FGM cracked during fabrication, indicating the formation of detrimental phases. The microstructure, composition, phases, and microhardness of the gradient zone were analyzed experimentally. The phase composition as a function of chemistry was predicted through thermodynamic calculations. It was determined that a significant amount of the intermetallic σ-FeV phase formed within the gradient zone. When the σ phase constituted the majority phase, catastrophic cracking occurred. The approach presented illustrates the suitability of using equilibrium thermodynamic calculations for the prediction of phase formation in FGMs made by AM despite the nonequilibrium conditions in AM, providing a route for the computationally informed design of FGMs.

Copyright
Corresponding author
a)Address all correspondence to this author. e-mail: amb961@psu.edu
References
Hide All
1.Domack, M.S. and Baughman, J.M.: Development of nickel–titanium graded composition components. Rapid Prototyp. J. 11, 41 (2005).
2.Suryakumar, S. and Somashekara, M.A.: Manufacture of functionally gradient materials using weld-deposition. In Proceedings of the 1st International Joint Symposium on Joining and Welding, Fujii, H., ed. (Woodheard Publishing Ltd., Osaka, Japan, 2013); pp. 939.
3.Shen, C., Pan, Z., Cuiuri, D., Roberts, J., and Li, H.: Fabrication of Fe-FeAl functionally graded material using the wire-arc additive manufacturing process. Metall. Mater. Trans. B 47, 763 (2016).
4.Nemat-Alla, M.M.: Powder metallurgical fabrication and microstructural investigations of aluminum/steel functionally graded material. Mater. Sci. Appl. 2, 1708 (2011).
5.Hofmann, D.C., Roberts, S., Otis, R., Kolodziejska, J., Dillon, R.P., Suh, J., Shapiro, A.A., Liu, Z-K., and Borgonia, J-P.: Developing gradient metal alloys through radial deposition additive manufacturing. Sci. Rep. 4, 5357 (2014).
6.Carroll, B.E., Otis, R., Borgonia, J-P., Suh, E., Dillon, P., Shapiro, A., Hofmann, D.C., Liu, Z-K., and Beese, A.M.: Functionally graded alloy of 304L stainless steel and inconel 625 fabricated by directed energy deposition: Characterization and thermodynamic modeling. Acta Mater. 108, 46 (2016).
7.Bobbio, L.D., Otis, R.A., Borgonia, J.P., Dillon, R.P., Shapiro, A.A., Liu, Z-K., and Beese, A.M.: Additive manufacturing of a functionally graded material from Ti–6Al–4V to invar: Experimental characterization and thermodynamic calculations. Acta Mater. 127, 133 (2017).
8.Koptseva, N.V., Golubchik, E.M., Yu, Y., Chukin, D.M., and Medvedeva, E.M.: Formation of the physicomechanical properties in high strength invar alloys. Steel Translat. 44, 317 (2014).
9.ASM Aerospace Specification Metals, Inc., 2015.
10.Roy, R., Agrawal, D.K., and McKinstry, H.A.: Very low thermal expansion coefficient materials. Annu. Rev. Mater. Res. 19, 59 (1989).
11.Tomashchuk, I., Grevey, D., and Sallamand, P.: Dissimilar laser welding of AISI 316L stainless steel to Ti–6Al–4V alloy via pure vanadium interlayer. Mater. Sci. Eng., A 622, 37 (2015).
12.Carroll, B.E., Palmer, T.A., and Beese, A.M.: Anisotropic tensile behavior of Ti–6Al–4V components fabricated with directed energy deposition additive manufacturing. Acta Mater. 87, 309 (2015).
13.Vander Voort, G.F.: Metallography, Principles and Practice (ASM International, Materials Park, Ohio, 1984).
14.Kaufman, L. and Bernstein, H.: Computer Calculation of Phase Diagram (Academic Press Inc., New York, 1970).
15.Saunders, N. and Miodownik, A.P.: CALPHAD (Calculation of Phase Diagrams): A Comprehensive Guide (Pergamon, Oxford, New York, 1998).
16.Lukas, H.L., Fries, S.G., and Sundman, B.: Computational Thermodynamics: The CALPHAD Method (Cambridge University Press, Cambridge, U.K., 2007).
17.Liu, Z.K.: First-principles calculations and CALPHAD modeling of thermodynamics. J. Phase Equilibria Diffusion 30, 517 (2009).
18.Liu, Z.K. and Wang, Y.: Computational Thermodynamics of Materials (Cambridge University Press, Cambridge, U.K., 2016).
19.Hofmann, D.C., Kolodziejska, J., Roberts, S., Otis, R., Dillon, R.P., Suh, J-O., Liu, Z-K., and Borgonia, J-P.: Compositionally graded metals: A new frontier of additive manufacturing. J. Mater. Res. 29, 1899 (2014).
20.Bobbio, L.D., Bocklund, B., Otis, R., Borgonia, J.P., Dillon, R.P., Shapiro, A.A., McEnerney, B., Liu, Z-K., and Beese, A.M.: Characterization of a functionally graded material of Ti–6Al–4V to 304L stainless steel with an intermediate V section. J. Alloys Compd. 742, 1031 (2018).
21.Zhao, C.C., Yang, S.Y., Lu, Y., Guo, Y.H., Wang, C.P., and Liu, X.J.: Experimental investigation and thermodynamic calculation of the phase equilibria in the Fe–Ni–V system. Calphad Comput. Coupling Phase Diagrams Thermochem. 46, 80 (2014).
22.Andersson, J.O., Helander, T., Höglund, L., Shi, P., and Sundman, B.: Thermo-Calc & DICTRA, computational tools for materials science. Calphad Comput. Coupling Phase Diagrams Thermochem 26, 273 (2002).
23.Smith, J.F.: The V (vanadium) system. Bull. Alloy Phase Diagrams 2, 40 (1981).
24.Davis, J.R., ed.: ASM Specialty Handbook: Nickel, Cobalt, and Their Alloys (ASM International, Materials Park, OH, 2000); pp. 92101.
25.Turchi, P.E.A., Kaufman, L., and Liu, Z-K.: Modeling of Ni–Cr–Mo based alloys: Part II—Kinetics. Calphad Comput. Coupling Phase Diagrams Thermochem. 31, 237 (2007).
26.Ustinovshikov, Y., Pushkarev, B., and Sapegina, I.: Phase transformations in alloys of the Fe–V system. J. Alloys Compd. 398, 133 (2005).
27.Hsieh, C. and Wu, W.: Overview of intermetallic sigma (σ) phase precipitation in stainless steels. ISRN Metall. 4, 1 (2012).
28.Seki, J.I., Hagiwara, M., and Suzuki, T.: Metastable order-disorder transition and sigma phase formation in Fe–V binary alloys. J. Mater. Sci. 14, 2404 (1979).
29.Samsonov, G.V., ed.: Handbook of the Physicochemical Properties of the Elements (Springer, New York, 1968).
30.Hoelzer, D.T., West, M.K., Zinkle, S.J., and Rowcliffe, A.F.: Solute interactions in pure vanadium and V–4Cr–4Ti alloy. J. Nucl. Mater. 283–287, 616 (2000).
31.Satou, M., Abe, K., and Kayano, H.: High-temperature deformation of modified V–Ti–Cr–Si type alloys. J. Nucl. Mater. 179, 757 (1991).
Recommend this journal

Email your librarian or administrator to recommend adding this journal to your organisation's collection.

Journal of Materials Research
  • ISSN: 0884-2914
  • EISSN: 2044-5326
  • URL: /core/journals/journal-of-materials-research
Please enter your name
Please enter a valid email address
Who would you like to send this to? *
×

Keywords:

Metrics

Full text views

Total number of HTML views: 2
Total number of PDF views: 21 *
Loading metrics...

Abstract views

Total abstract views: 55 *
Loading metrics...

* Views captured on Cambridge Core between 15th May 2018 - 25th May 2018. This data will be updated every 24 hours.