Hostname: page-component-848d4c4894-mwx4w Total loading time: 0 Render date: 2024-06-20T04:45:39.842Z Has data issue: false hasContentIssue false
  • English
  • Français

Uniqueness of reverse analysis from conical indentation tests

Published online by Cambridge University Press:  03 March 2011

K.K. Tho ,
S. Swaddiwudhipong ,
Z.S. Liu ,
K. Zeng  and
J. Hua
K.K. Tho
Affiliation:
Department of Civil Engineering, National University of Singapore, Singapore 119260
S. Swaddiwudhipong
Affiliation:
Department of Civil Engineering, National University of Singapore, Singapore 119260
Z.S. Liu
Affiliation:
Institute of High Performance Computing, 1 Science Park Road, #01-01, Singapore 117528
K. Zeng
Affiliation:
Institute of Material Research and Engineering, 3 Research Link, Singapore 117602
J. Hua
Affiliation:
Department of Civil Engineering, National University of Singapore, Singapore 119260
Get access

Abstract

The curvature of the loading curve, the initial slope of the unloading curve, and the ratio of the residual depth to maximum indentation depth are three main quantitiesthat can be established from an indentation load-displacement curve. A relationship among these three quantities was analytically derived. This relationship is valid for elasto-plastic material with power law strain hardening and indented by conical indenters of any geometry. The validity of this relationship is numerically verified through large strain, large deformation finite element analyses. The existence of an intrinsic relationship among the three quantities implies that only two independent quantities can be obtained from the load-displacement curve of a single conical indenter. The reverse analysis of a single load-displacement curve will yield non-unique combinations of elasto-plastic material properties due to the availability of only two independent quantities to solve for the three unknown material properties.

Keywords

IndentationMechanical propertiesStress/strain relationship
Type
Articles
Information
Journal of Materials Research , Volume 19 , Issue 8 , August 2004 , pp. 2498 - 2502
Copyright
Copyright © Materials Research Society 2004

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

REFERENCES

1.Giannakopoulos, A.E. and Suresh, S.Determination of elastoplastic properties by instrumented sharp indentation. Scripta Mater. 40, 1191 (1999).CrossRefGoogle Scholar
2.Dao, M., Chollacoop, N., Van Vliet, K.J., Venkatesh, T.A. and Suresh, S.: Computational modelling of the forward and reverse problems in instrumented sharp indentation. Acta Mater 49, 3899 (2001).CrossRefGoogle Scholar
3.Chollacoop, N., Dao, M. and Suresh, S.Depth-sensing instrumented indentation with dual sharp indenters. Acta Mater. 51, 3713 (2003).CrossRefGoogle Scholar
4.Zeng, K. and Chiu, C.H.An analysis of load-penetration curves from instrumented indentation. Acta Mater. 49, 3539 (2001).CrossRefGoogle Scholar
5.Cheng, Y.T. and Cheng, C.M.Can stress-strain relationships be obtained from indentation curves using conical and pyramidal indenters? J. Mater. Res. 14, 3493 (1999).CrossRefGoogle Scholar
6.Capehart, T.W. and Cheng, Y.T.Determining constitutive models from conical indentation: Sensitivity analysis. J. Mater. Res. 18, 827 (2003).CrossRefGoogle Scholar
7.Tho, K.K., Swaddiwudhipong, S., Liu, Z.S. and Zeng, K. Simulation of instrumented indentation and material characterization. (submitted for publication).Google Scholar
8.Oliver, W.C. and Pharr, G.M.: An improved technique for determining hardness and elastic modulus using load and displacement sensing indentation experiments. J. Mater. Res. 7, 1564 (1992).CrossRefGoogle Scholar
9.Loubet, J.L., Georges, J.M., Marchesini, O. and Meille, G.Vickers indentation curves of magnesium oxide (MgO). J. Tribol. 106, 43 (1984).CrossRefGoogle Scholar
10.Cheng, Y.T., Li, Z. and Cheng, C.M.Scaling relationships for indentation measurements. Philos. Mag. A 82, 1821 (2002).CrossRefGoogle Scholar
11.Bucaille, J.L., Stauss, S., Felder, E. and Michler, J.Determination of plastic properties of metals by instrumented indentation using different sharp indenters. Acta Mater. 51, 1663 (2003).CrossRefGoogle Scholar
12.Kalpakjian, S. and Schmid, S.R.Manufacturing Processes for Engineering Materials, (Prentice Hall, New Jersey, 2003), p. 33.Google Scholar
13. MatWeb: http://www.matweb.com, 2003, by Automation Creations, Inc.Google Scholar