Hostname: page-component-848d4c4894-75dct Total loading time: 0 Render date: 2024-04-30T12:24:36.989Z Has data issue: false hasContentIssue false
  • English
  • Français

A correction method of elastic modulus in compression tests for linear hardening materials

Published online by Cambridge University Press:  21 December 2015

Wei Liu ,
Yong Huan ,
Jie Dong ,
Yujing Dai  and
Ding Lan
Wei Liu
Affiliation:
State Key Laboratory of Nonlinear Mechanics (LNM), Institute of Mechanics, Chinese Academy of Sciences, Beijing 100190, China Key Laboratory of Microgravity (National Microgravity Laboratory), Institute of Mechanics, Chinese Academy of Sciences (CAS), Beijing 100190, China
Yong Huan*
Affiliation:
State Key Laboratory of Nonlinear Mechanics (LNM), Institute of Mechanics, Chinese Academy of Sciences, Beijing 100190, China
Jie Dong
Affiliation:
State Key Laboratory of Nonlinear Mechanics (LNM), Institute of Mechanics, Chinese Academy of Sciences, Beijing 100190, China
Yujing Dai
Affiliation:
State Key Laboratory of Nonlinear Mechanics (LNM), Institute of Mechanics, Chinese Academy of Sciences, Beijing 100190, China
Ding Lan
Affiliation:
Key Laboratory of Microgravity (National Microgravity Laboratory), Institute of Mechanics, Chinese Academy of Sciences (CAS), Beijing 100190, China
*
Address all correspondence to Yong Huan athuany@lnm.imech.ac.cn
Get access

Abstract

A correction method for linear hardening materials is brought forward to obtain the true (or nearly true) modulus of cylindrical specimens with middle aspect ratios in compression tests. By considering the stress concentration near the interface between the specimen and the compression platen caused by slanted contact, a “sandwich” model is developed. A correction formula is derived and all parameters can be obtained from the tested stress–strain curve. Experiments were performed on Al 2024 specimens with four aspect ratios. The corrected results are closer to the intrinsic modulus than the tested values, which verify the effectiveness of the correction method.

Type
Research Letters
Information
MRS Communications , Volume 5 , Issue 4 , December 2015 , pp. 641 - 645
Copyright
Copyright © Materials Research Society 2015 

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

References

1. Chau, K.T.: Young's modulus interpreted from compression tests with end friction. J. Eng. Mech. 123, 1 (1997).Google Scholar
2. Jones, R.M.: Apparent flexural modulus and strength of multimodulus materials. J. Compos. Mater. 10, 342 (1976).Google Scholar
3. Sun, J.Y., Zhu, H.Q., Qin, S.H., Yang, D.L., and He, X.T.: A review on the research of mechanical problems with different moduli in tension and compression. J. Mech. Sci. Technol. 24, 1845 (2010).Google Scholar
4. Medri, G.: A nonlinear elastic model for isotropic materials with different behavior in tension and compression. J. Eng. Mater. Technol. — Trans. ASME 104, 26 (1982).Google Scholar
5. Backofen, W.A.: Deformation processing. Metall. Trans. 4, 2679 (1973).Google Scholar
6. Kuhn, H.: Uniaxial compression testing. In ASM Handbook Volume 08 Mechanical Testing & Evaluation, edited by Kuhn, H. and Medlin, D. (ASM International, Materials Park, OH, 2000), pp. 340.Google Scholar
7. Schroers, J. and Johnson, W.L.: Ductile bulk metallic glass. Phys. Rev. Lett. 93, 255506-1 (2004).Google Scholar
8. Liu, Y.H., Wang, G., Wang, R.J., Zhao, D.Q., Pan, M.X., and Wang, W.H.: Super plastic bulk metallic glasses at room temperature. Science 315, 1385 (2007).Google Scholar
9. Song, S.X., Beib, H., Wadsworthc, J., and Nieha, T.G.: Flow serration in a Zr-based bulk metallic glass in compression at low strain rates. Intermetallics 16, 813 (2008).Google Scholar
10. Williams, J.G. and Gamonpilas, C.: Using the simple compression test to determine Young's modulus, Poisson's ratio and the Coulomb friction coefficient. Int. J. Solids Struct. 45, 4448 (2008).CrossRefGoogle Scholar
11.ASTM E9-09, Standard Test Methods of Compression Testing of Metallic Materials at Room Temperature, ASTM International, West Conshohocken, PA, 2009. http://www.astm.org Google Scholar