Hostname: page-component-7dd5485656-bvgqh Total loading time: 0 Render date: 2025-10-30T16:02:10.142Z Has data issue: false hasContentIssue false
  • English
  • Français

Influence of annealing on ductility of ultrafine-grained titanium processed by equal-channel angular pressing–Conform and drawing

Published online by Cambridge University Press:  24 September 2013

Alexander V. Polyakov ,
Irina P. Semenova ,
Ruslan Z. Valiev ,
Yi Huang  and
Terence G. Langdon
Alexander V. Polyakov
Affiliation:
Institute of Physics of Advanced Materials, Ufa State Aviation Technical University, K. Marx St., 12, Ufa 450000, Russia
Irina P. Semenova
Affiliation:
Institute of Physics of Advanced Materials, Ufa State Aviation Technical University, K. Marx St., 12, Ufa 450000, Russia
Ruslan Z. Valiev
Affiliation:
Institute of Physics of Advanced Materials, Ufa State Aviation Technical University, K. Marx St., 12, Ufa 450000, Russia
Yi Huang*
Affiliation:
Materials Research Group, Faculty of Engineering and the Environment, University of Southampton, Southampton SO17 1BJ, UK
Terence G. Langdon
Affiliation:
Materials Research Group, Faculty of Engineering and the Environment, University of Southampton, Southampton SO17 1BJ, UK; Departments of Aerospace and Mechanical Engineering and Materials Science, University of Southern California, Los Angeles, California 90089-1453
*
Address all correspondence to Yi Huang atY.Huang@soton.ac.uk
Get access

Abstract

A Grade 4 titanium was processed by equal-channel angular pressing (ECAP)–Conform and drawing to produce an ultrafine grain (UFG) size of ~180 nm. Some samples were tested in this condition (UFG-1) and others were annealed for 1 h at 623 K (UFG-2). The grain boundaries are in a non-equilibrium condition after processing, but the annealing equilibrates the boundaries without any increase in grain size. This leads to significant differences in the mechanical behavior of UFG-1 and UFG-2 when they are tested at 293 and 623 K.

Information

Type
Research Letters
Information
MRS Communications , Volume 3 , Issue 4 , December 2013 , pp. 249 - 253
Copyright
Copyright © Materials Research Society 2013 

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

Article purchase

Temporarily unavailable

References

1.Valiev, R.Z., Islamgaliev, R.K., and Alexandrov, I.V.: Using high-pressure torsion for metal processing: fundamentals and applications. Prog. Mater. Sci. 45, 103 (2000).Google Scholar
2.Zhu, Y.T. and Liao, X.Z.: Nanostructured metals: retaining ductility. Nat. Mater. 3, 351 (2004).Google Scholar
3.Valiev, R.Z.: Nanostructuring of metals by severe plastic deformation for advanced properties. Nat. Mater. 3, 511 (2004).Google Scholar
4.Semenova, I.P., Valiev, R.Z., Yakushina, E.B., Salimgareeva, G.H., and Lowe, T.C.: Strength and fatigue properties enhancement in ultrafine-grained Ti produced by severe plastic deformation. J. Mater. Sci. 43, 7354 (2008).Google Scholar
5.Valiev, R.Z., Semenova, I.P., Latysh, V.V., Rack, H., Lowe, T.C., Petruzelka, J., Dluhos, L., Hrusak, D., and Sochova, J.: Nanostructured titanium for biomedical applications. Adv. Eng. Mater. 10, B15 (2008).CrossRefGoogle Scholar
6.Estrin, Y. and Vinogradov, A.V.: Extreme grain refinement by severe plastic deformation: a wealth of challenging science. Acta Mater. 61, 782 (2013).CrossRefGoogle Scholar
7.Valiev, R.Z. and Langdon, T.G.: Principles of equal-channel angular pressing as a processing tool for grain refinement. Prog. Mater. Sci. 51, 881 (2006).Google Scholar
8.Green, D.: Continuos extrusion-forming of wire sections. J. Inst. Met. 100, 295 (1972).Google Scholar
9.Etherington, C.: CONFORM—a new concept for the continuous extrusion forming of metals. J. Eng. Ind. 96, 893 (1974).Google Scholar
10.Raab, G.J., Valiev, R.Z., Lowe, T.C., and Zhu, Y.T.: Continuous processing of ultrafine grained Al by ECAP–Conform. Mater. Sci. Eng. 382, 30 (2004).CrossRefGoogle Scholar
11.Xu, C., Schroeder, S., Berbon, P.B., and Langdon, T.G.: Principles of ECAP–Conform as a continuous process for achieving grain refinement: application to an aluminum alloy. Acta Mater. 58, 1379 (2010).CrossRefGoogle Scholar
12.Valiev, R.Z. and Langdon, T.G.: Achieving exceptional grain refinement through severe plastic deformation: new approaches for improving the processing technology. Metall. Mater. Trans. 42A, 2942 (2011).Google Scholar
13.Polyakov, A.V., Gunderov, D.V., Raab, G.I.: Evolution of microstructure and mechanical properties of titanium grade 4 with the increase of the ECAP–Conform passes. Mater. Sci. Forum 667–669, 1165 (2011).Google Scholar
14.Semenova, I.P., Polyakov, A.V., Raab, G.I., and Lowe, T.C.: Enhanced fatigue properties of ultrafine-grained Ti rods processed by ECAP–Conform. J. Mater. Sci. 47, 7777 (2012).Google Scholar
15.Gunderov, D.V., Polyakov, A.V., Semenova, I.P., Raab, G.I., Churakova, A.A., Gimaltdinova, E.I., Sabirov, I., Segurado, J., Sitdikov, V.D., Alexandrov, I.V., Enikeev, N.A., and Valiev, R.Z.: Evolution of microstructure, macrotexture and mechanical properties of commercially pure Ti during ECAP–conform processing and drawing. Mater. Sci. Eng. A562, 128 (2013).Google Scholar
16.Valiev, R.Z., Sergueeva, A.V., and Mukherjee, A.K.: The effect of annealing on tensile deformation behaviour of nanostructured SPD titanium. Scr. Mater. 49, 669 (2003).Google Scholar
17.Semenova, I.P., Salimgareeva, G.H., Da Costa, G., Lefebvre, W., and Valiev, R.Z.: Enhanced strength and ductility of ultrafine-Grained Ti processed by severe plastic deformation. Adv. Eng. Mater. 12, 803 (2010).CrossRefGoogle Scholar
18.Furukawa, M., Iwahashi, Y., Horita, Z., Nemoto, M., and Langdon, T.G.: The shearing characteristics associated with equal-channel angular pressing. Mater. Sci. Eng. A257, 328 (1998).Google Scholar
19.Iwahashi, Y., Wang, J., Horita, Z., Nemoto, M., and Langdon, T.G.: Principle of equal-channel angular pressing for the processing of ultra-fine grained materials. Scr. Mater. 35, 143 (1996).Google Scholar
20.Langdon, T.G.: Seventy-five years of superplasticity: historic developments and new opportunities. J. Mater. Sci. 44, 5998 (2009).Google Scholar
21.Woodford, D.A.: Strain-rate sensitivity as a measure of ductility. Trans. ASM 62, 291 (1969).Google Scholar
22.Valiev, R.Z., Salimonenko, D.A., Tsenev, N.K., Berbon, P.B., and Langdon, T.G.: Observations of high strain rate superplasticity in commercial aluminum alloys with ultrafine grain sizes. Scr. Mater. 37, 1945 (1997).Google Scholar
23.McFadden, S.X., Mishra, R.S., Valiev, R.Z., Zhilyaev, A.P., and Mukherjee, A.K.: Low-temperature superplasticity in nanostructured nickel and metal alloys. Nature 398, 684 (1999).Google Scholar
24.Mishra, R.S., Valiev, R.Z., McFadden, S.X., Islamgaliev, R.K., and Mukherjee, A.K.: High-strain-rate superplasticity from nanocrystalline Al alloy 1420 at low temperatures. Phil. Mag. A81, 37 (2001).Google Scholar
25.Sergueeva, A.V., Stolyarov, V.V., Valiev, R.Z., and Mukherjee, A.K.: Superplastic behaviour of ultrafine-grained Ti–6A1–4V alloys. Mater. Sci. Eng. A323, 318 (2002).Google Scholar
26.Kawasaki, M. and Langdon, T.G.: Principles of superplasticity in ultrafine-grained materials. J. Mater. Sci. 42, 1782 (2007).Google Scholar
27.Kawasaki, M., Balasubramanian, N., and Langdon, T.G.: Flow mechanisms in ultrafine-grained metals with an emphasis on superplasticity. Mater. Sci. Eng. A528, 6624 (2011).Google Scholar