By using quasi-optical tools, it is possible to approximate microwave radiation to Gaussian beams, which enables the study of its propagation and coupling to different components. Hence, their usefulness for wireless power transfer and rapid system design. In this paper, a system composed of two reflectors is analyzed both theoretically and by discussing two cases where quasi-optical tools were applied. The near- and far-field regimes were considered and corresponding frequencies of operation, beam radius, and radius of curvature were computed.

The performance of wireless power transfer (WPT) systems is a function of many parameters such as resonance matching, coil quality factor, system impedance match, and others. When designing and testing WPT systems, reliable measurement of system performance is essential. In our application, we use WPT to power biomedical implants for telemetry acquisition from small rodents, where rodent behavior data is used to study disease models. Such an application employs a large primary coil and a much smaller moving secondary coil, which can be defined as a loosely coupled WPT (LCWPT) system. This paper presents a novel wireless measurement system (WMS) that is used to collect real-time performance data from the secondary circuit (implant), while testing LCWPT systems. Presently, measuring the performance of the secondary side of LCWPT systems while they are in operation can be problematic. The literature reports various measurement errors when using voltage/current probes, or coaxial cables placed directly into the primary magnetic field. We have designed the WMS to greatly reduce such measurement errors, where the WMS measures the induced voltage (and hence received power) and relays this information by radio. Experiments were done to test the WMS, as well as comparison with cable-based measurements.

Here we demonstrate wireless energy transfer that exploits the conductivity and permittivity of soil to create a potential gradient on the surface around an earthed electrode, distributing electrical energy over the area. This generated surface potential can be amplified using a special standing-wave receiver for harnessing the distributed energy. We have experimentally mapped the surface potential around the electrode and plotted the received energy covering an area of 1200 m2. Key operating parameters are determined with a discussion on optimizing the system efficiency. This technique could address the challenge of distributing electrical energy to many low power devices over large outdoor areas without the use of wires.

In the past few years Radio Frequency Identification (RFID) has grown to be one of the most popular technologies in the area of identification systems. Following a brief survey of RFID systems, this paper provides a technical review of work undertaken in the field of time-domain chipless RFID tags and sensors. This paper aims not only to address the chipless tags which use Time Domain Reflectometry (TDR) concept for data encoding but also for the use of Ultra-Wideband Impulse-Radar (UWB-IR) as a time-domain measurement technique. The penultimate section intends to focus on time-domain reading setups and finally, a brief comparison between this method and other chipless techniques is provided.

Magneto-inductive waves are a form of propagation which only exists in certain types of magnetic metamaterials formed from inductively coupled resonant circuits. We present an investigation of their potential as contactless power transfer devices capable of carrying power along a surface between suitably prepared terminals while simultaneously offering a broadband data channel. Input impedances and their matching conditions are explored with a view to offering a simple power system design. A device with 75% peak and 40% minimum efficiency is demonstrated and designs with potential for better than 70% mean and 90% peak are reported. The product of planar magnetic coupling and metamaterial cell Q factor is determined to be a key optimization parameter for high efficiency.

Design steps are outlined for maximizing the RF-to-dc power conversion efficiency (PCE) of a rectenna. It turns out that at a frequency of 868 MHz, a high-ohmic loaded rectifier will lead to a highly sensitive and power conversion efficient rectenna. It is demonstrated that a rectenna thus designed, using a 50 Ω antenna and lumped element matching network gives a superior PCE compared with state of the art also for lower resistive loading. By omitting the matching network and directly, conjugate impedance matching the antenna to the rectifier, the PCE may be further increased and the rectenna size reduced as it is demonstrated with a rectenna prototype measuring only 0.028 squared wavelengths at 868 MHz and demonstrating a PCE of 55% for a −10 dBm RF input power level.

Electric vehicles (EVs) are becoming more popular due to concerns about the environment and rising gasoline prices. However, the charging infrastructure is lacking, and most people can only charge their EVs at home if they remember to plug in their cars. Using the principles of magnetic inductance and magnetic resonance, wireless charging (WC) could help significantly with these infrastructure problems by making charging secure and convenient. WC systems also have the potential to provide dynamic charging, making long road trips with EVs feasible and eliminating range anxiety. In this paper, we review the companies available in the literature that have developed electric vehicle wireless charging systems, automobile manufacturers interested in such technology, and research from universities and laboratories on the topic. While the field is still very young, there are many promising technologies available today. Some systems have already been in use for years, recharging public transit buses at bus stops. Safety and regulations are also discussed.

We propose a wireless power distribution system (WPDS) operating at 2.45 GHz CW in buildings instead of wired power distribution in order to reduce the initial cost of the building. Required technologies for the WPDS are (a) low-cost and low-loss deck plate waveguide, (b) variable microwave power distributor for the waveguide, and (c) high-power (>100 W) rectifier at the outlet. We developed and tested the deck plate waveguide, power distributor, and high-power rectenna consisting of 256 Si Schottky barrier diodes and newly developed GaN diodes. Finally, a test WPDS was built and microwave power transmission experiments were conducted. The total efficiency of the test WPDS was estimated to be 52%.

This paper is dedicated to the extensive review of state-of-the-art contactless energy transfer (CET) systems that are gaining increasing interest in the automatic machinery industries. We first introduce the circuit equivalent networks considered in the literature, and discuss the main operating principles. Possible circuital resonant solutions are also discussed together with the required compensating networks. Then we focus on the problem of transferring, at the maximum efficiency, high-power levels (of the order of 1 kW or higher), showing that highly coupled inductive links are needed, requiring to refrain from the resonance condition. These systems are usually referred to as CET systems, since the link distances are negligible with respect to the coils dimensions. The operating frequencies are of the order of tens to hundreds of kilohertz. The fundamental figures of merit are analytically defined and used to measure the actual limitations involved in this class of systems, including aspects related to realization feasibility with respect to voltages and currents limitations. Finally, state-of-the-art CET works are surveyed, and realistic applications for different operating frequencies are considered and critically compared.