1 Introduction
Owing to their compact structure, high conversion efficiency and robust operation, high-power fiber lasers have attracted much research interest and have been widely employed in many fields[Reference Kawahito, Wang, Katayama and Sumimori1–Reference Fan, Zhao, Shi, Xiao and Hu4]. Rare-earth-doped fiber lasers, as a significant mainstay of high-power fiber lasers[Reference Jeong, Sahu, Payne and Nilsson5–Reference Huang, Lai, Ma, Wang, Su, Ma, Li, Zhi and Zhou9], however, are challenged by waste heat accumulation in the active fiber[Reference Aydin, Fortin, Maes, Jobin, Jackson, Vallée and Bernier10], especially with the power increasing beyond kilowatt level[Reference Fan, He, Zhou, Zheng, Liu, Wei, Dong and Lou11–Reference Smith and Smith15]. The quantum defect (QD) is one of the most important heat sources in the gain fiber, which could result in serious thermal effects on fiber lasers, such as the thermal lens effect, thermal mode instability and additional noise[Reference Jauregui, Stihler and Limpert16–Reference Knall, Engholm, Boilard, Bernier and Digonnet18].
Continuous efforts have been focused on reducing the QD[Reference Yu, Cavillon, Kucera, Hawkins, Ballato and Dragic19–Reference Xu, Ye, Xiao, Leng, Liu and Zhou23]. Benefiting from fast development of the high-brightness pump source, Raman fiber lasers (RFLs) have been rapidly developed and widely investigated in recent years[Reference Supradeepa, Feng and Nicholson24–Reference Shamir, Glick, Aviel, Attias and Pearl27]. Surprisingly, fiber lasers based on stimulated Raman scattering (SRS) show outstanding performance for thermal management at the 1 μm band. Generally, the QD of RFLs is around 5%[Reference Shamir, Glick, Aviel, Attias and Pearl27], which is half that of the common laser diode (LD)-pumped Yb-doped fiber laser. Employing tens of meters or even km-level passive fiber, RFLs can effectively relieve the density of the thermal deposition. Besides, the characteristic of non-photon-darkening enables RFLs to maintain stable operation. Accordingly, the RFL is a promising alternative for both high-power and low-QD fiber lasers. Up to hundreds of watt-level high-power RFLs in all-fiber formats have been demonstrated by several independent groups[Reference Feng, Taylor and Calia28–Reference Supradeepa and Nicholson31]. By adopting a main-oscillator–power-amplifier structure, up to 3 kW RFLs have been demonstrated[Reference Chen, Yao, Xiao, Leng and Zhou32, Reference Chen, Yao, Xiao, Leng and Zhou33]. Usually, the high-power fiber lasers aforementioned have QDs of about 4%–5% based on the 13.2 THz frequency shift. Note that a challenge in power scaling of RFLs has also been revealed and observed very recently[Reference Naderi, Dajani, Grosek and Madden34–Reference Song, Ma, Ren, Zhang, Liu, Xiao, Zhang and Zhou37], where further decreasing the QD of the RFL is one of the promising solutions for power scaling.
Moreover, it has been reported that there is a gain peak with a frequency shift of less than 4 THz, called the boson peak in phosphorus-doped fiber (PDF), which may enable RFLs to further reduce the QD[Reference Zhang, Xu, Ye, Song, Yao and Zhou38]. Recently, up to 100-watt-level core-pumped RFLs with less than 1% QD have been demonstrated[Reference Ma, Ye, Zhang, Xu, Huang, Leng, Pan and Zhou39]. The results have indicated that the RFL gained by the boson peak of the PDF has the ability to realize low-QD output. Nevertheless, it is difficult to enhance the pump density for power scaling in conventional core-pumped RFLs due to the limitations of the power handling capacity and the small mode area of the core in a single-mode fiber. One of the solutions to this challenge is cladding pumping[Reference Zervas and Codemard2, Reference Jeong, Sahu, Payne and Nilsson5, Reference Jauregui, Limpert and Tünnermann8, Reference Snitzer, Po, Hakimi, Tumminelli and McCollum40–Reference Zhou, Huang, Leng, Xiao, Xu and Yao44]. The pump light is guided in the cladding of the fiber, which can significantly decrease the requirement on the pump brightness. Since the first demonstration of the cladding-pumped Raman regime[Reference Nilsson, Sahu, Jang, Selvas, Hanna and Grudinin45], there has been growing research interest, and significant advances in high-power RFLs have been successfully achieved[Reference Codemard, Ji, Sahu and Nilsson46–Reference Chen, Yao, Xiao, Leng and Zhou48]. However, for thermal management, the QDs of cladding-pumped RFLs currently reported were almost more than 4%, and the realization of a further reduced QD has been dilatory owing to weak gain intensity with a tiny frequency shift of passive fiber and low pump intensity in the fiber cladding, which follows the intense gain competition and eliminates the short signal wavelength. Should the QD of the cladding-pumped RFL be further decreased, it would be a promising solution for high-power fiber lasers because it combines the advantages of RFLs, cladding pumping and low heat production.
In this paper, we demonstrate a cladding-pumped RFL with QD reduced to less than 1%, which is the lowest QD ever achieved in a cladding-pumped RFL, to our knowledge. Gained by the boson peak of the PDF, 0.78% QD with output power of 23.7 W has been successfully achieved. Furthermore, by optimizing the system parameters, such as the output coupler (OC) reflectivity and the fiber length, the Raman power can be scaled up to 47.7 W with a QD of 1.29%. This work experimentally verifies the feasibility and potential of low-QD RFL.
2 Experimental setup
The experimental setup is a forward-pumped Raman oscillator, as shown in Figure 1(a). A home-made amplified spontaneous emission (ASE) source is used as the pump, with a wavelength tuning range of 1050–1080 nm and 3-dB bandwidth of 1.7 nm[Reference Ye, Xu, Zhang, Song, Leng and Zhou49]. The usage of ASE as the pump source instead of the classical fiber-cavity-based oscillator has the advantages of low coherence and high temporal stability, which could reduce the intensity noise and improve the laser performances[Reference Chen, Song, Ye, Yao, Xu, Xiao, Leng and Zhou50–Reference Ye, Xu, Song, Zhang, Zhang, Xiao, Leng and Zhou52]. A fiber circulator with core diameter of 20 μm is mounted after the ASE source, to protect the pump from the potential backward laser and to monitor the backward light from the following oscillator. Port 2 of the circulator is spliced with a Raman oscillator, which is constructed with a highly reflective fiber Bragg grating (HR FBG), a section of PDF and an OC. The HR FBG with approximately 99% reflectivity and the OC are both located at 1086.5 nm, and are written on the used PDF. All free ends are 8°-cleaved to suppress the parasitic reflection.
(a) The experimental setup of the low-QD RFL. (b) The structure of the PDF. (c) Properties of the Raman frequency shift of the PDF.
The PDF is a piece of triple-cladding fiber with core/inner cladding diameter of 10/20 μm and numerical apertures (NAs) of 0.07 and 0.14, respectively, as shown in Figure 1(b). Figure 2 describes the schematics of laser transmission in cladding pumping and core pumping. Compared with the core pumping scheme in Figure 2(b), the pump light in the cladding pumping scheme is coupled into the inner cladding of the gain fiber, as depicted in Figure 2(a). Thus, the refractive index from the core to the outer cladding is designed to be decreased gradually, in order to ensure the total reflection inside the fiber. Properties of the Raman frequency shift in the range of 0–15 THz of the PDF are shown in Figure 1(c). The frequency shift of the boson peak is located at approximately 3.6 THz. It should be noted that the phosphorus only resided in the fiber core, which enables the pump light to be converted into the signal in the core through the small frequency shift of the boson peak, as the pump propagates along the fiber.
Schematic diagrams of laser transmission in (a) cladding pumping and (b) core pumping.
To analyze the output properties of the cladding-pumped RFL, a core-pumped RFL using the same experimental structure is constructed as a comparison. The circulator in the core-pumped RFL has the maximal optical power from port 1 to port 2 of 100 W, and the core/cladding diameter of the optical fiber is 10/125 μm.
3 Results and discussion
3.1 Verification of cladding-pumped low-QD operation
As the operation wavelength of the FBG pair is located at 1086.5 nm, we firstly tuned the central wavelength of the ASE source to 1072.5 nm to match the boson peak with a Raman frequency shift of approximately 3.6 THz, corresponding to a QD of 1.29%. In this section, we realized the cladding-pumped low-QD RFL and contrasted the properties of cladding pumping and core pumping.
The output characteristics under the two pump schemes are analyzed, with a 1 km PDF and OC with 10% reflectivity, as shown in Figure 3. Figure 3(a) shows that the power of the 1086.5 nm signal laser depends on the pump power of the two pump schemes. It can be measured that in core pumping scheme, the lasing threshold is 21.8 W and the maximal signal power is 20.5 W at a pump power of 64.7 W, with a slope efficiency of 47.8%. Yet, in the cladding pumping scheme, due to the larger area of inner cladding, the power density of the pump with the same pump power is lower, so that the Raman laser threshold is higher than that in the core pumping scheme. In addition, with 76.0 W pump power, the maximal power of the 1086.5 nm Raman laser obtained from cladding pumping scheme reaches 26.6 W, with a slope efficiency of 55.9%. However, the residual pump power in the cladding pumping scheme is higher than that in core pumping scheme with the same pump power, as shown in Figure 3(b). This could be attributed to the standard circle shape of the inner cladding inside the used PDF, which cannot suppress the spiral light propagating along the fiber and can cause incomplete conversion of the pump power in the cladding[Reference Liu and Ueda53].
Power evolutions of (a) the 1086.5 nm signal and (b) the residual pump, in two pump schemes. (c) The normalized intensity spectra as a function of wavelength, with 55 W pump power.
Figure 3(c) depicts the normalized intensity spectra of the two pump schemes with 55 W pump power. It can be found that with the same pump power, the spectral broadening of the 1086.5 nm peak in the cladding pumping scheme is weaker, which is caused by different distributions of the signal propagating along the fiber core between the two schemes. Under the same system condition, the pump power in the cladding pumping scheme is converted closer to the end of the fiber than that in the core pumping scheme, which can suppress the spectral broadening to some extent during the laser propagation[Reference Jiang, Zhang and Feng54]. Meanwhile, the signal light in the cladding pumping scheme can propagate a shorter distance before emitting from the fiber, causing the lower propagation loss and higher slope efficiency (see Figure 3(a)). In the cladding pumping scheme, the 1100.5 nm peak, which is caused by the Raman-assisted three-wave mixing (RATWM) effect[Reference Wang55], is 6.7 dB higher than that in the core pumping scheme. This is because there is more residual pump power in the cladding pumping scheme, which contributes to a stronger three-wave mixing (TWM) effect. The Stokes light of 1132 nm in the core pumping scheme is more conspicuous, and is converted from the pump wavelength through 14.7 THz silicon-based Raman gain. In the core pumping scheme, the pump laser, which propagates inside the fiber core, has higher power density than that in the cladding pumping scheme, which imposes stronger gain on the Stokes light of 1132 nm and limits the power scaling of the signal (see Figure 3(a)).
3.2 Performance exploration of cladding-pumped low-QD RFL
In this section, we optimized the parameters of the cladding-pumped RFL with a QD of 1.29% to improve the performance, and further explored the potential of the RFL on QD of less than 1%.
To facilitate the consumption of pump power in the cladding pumping scheme, OCs with 4%, 10% and 19% reflectivity are spliced with the output end of a 1 km PDF, respectively. The corresponding output properties of the cladding-pumped RFL are displayed in Figure 4. As the OC reflectivity increases, the feedback of the 1086.5 nm Raman laser is enhanced, which leads to a lower generation threshold and higher output power with the same pump power, as shown in Figure 4(a). With 19% OC reflectivity, after the pump power exceeds the laser threshold of 22.6 W, the power of the 1086.5 nm signal laser rises rapidly and reaches the maximum of 28.4 W with 72.5 W pump power. The corresponding slope efficiency is 56.9%. Figure 4(b) depicts the residual pump power evolutions with different OC reflectivities. With an increase in the OC reflectivity, the power density of the signal laser is more intense, which causes the pump power to be converted more substantially. With 19% OC reflectivity, the residual pump power increases to 10.5 W and then falls off until 2.1 W. Limited by the experimental conditions, low-QD performances with higher OC reflectivity cannot be investigated presently. If the OC reflectivity increases further, the high signal power density may enhance the silicon-based Raman gain and promote the generation of 1132 nm Stokes light, which may limit the power scaling of the signal.
To further improve the performances of the cladding-pumped RFL, PDFs at lengths of 300 m, 400 m, 500 m, 600 m and 1 km with 19% OC reflectivity are used in the Raman oscillator, respectively. The performances are compared in Figure 5. The power of the 1086.5 nm signal laser as a function of pump power is depicted in Figure 5(a). It can be found that the longer the fiber, the lower the laser threshold. With 400 m PDF, the final power of the 1086.5 nm signal achieves the highest value of 47.7 W with the maximal pump power of 89.2 W, and the corresponding slope efficiency is 87.2%. Figure 5(b) describes the residual pump power evolutions related with the fiber length. Under the same pump power, with longer fiber, the pump power is consumed and converted more completely, which results in the lower laser threshold of 1086.5 nm. With 400 m PDF, the residual pump power is 11.5 W under the maximal pump power.
Power evolutions of (a) the 1086.5 nm signal and (b) the residual pump as functions of pump power, with different OC reflectivities.
Power evolutions of (a) the 1086.5 nm signal and (b) the residual pump as functions of pump power, with different PDF lengths.
To explore the potential on lower QD output (e.g., QD <1%) of the cladding-pumped phosphorus-doped RFL, we tuned the pump wavelength of the ASE source from 1072.5 nm to 1074, 1076 and 1078 nm, with corresponding QDs of 1.29%, 1.15%, 0.97% and 0.78%, respectively. Figure 6 describes the power evolutions of the 1086.5 nm signal laser and the residual pump dependence on different QD outputs, with 400 m PDF and 19% OC reflectivity. It can be seen from Figure 6(a) that as the QD is reduced, the generation threshold is higher and the signal power is lower, due to the decreasing Raman gain with smaller frequency shift in the PDF. With a QD of 0.78%, the Raman power rises quickly and achieves 23.7 W with the maximal pump power of 89.2 W. The corresponding slope efficiency is 77.0%. The increasing generation threshold can be addressed by further optimizations of system parameters, such as OC reflectivity. The low Raman gain provided by the boson peak at a red-shift pump wavelength also causes incomplete pump conversion, as shown in Figure 6(b). After the signal is generated, it can be observed that with the same pump power, the residual pump power is higher with lower QD output. Besides, the low power density of the signal, which is attributed to the weak reflectivity of the OC and the gain fiber with inapposite length, makes a contribution to the insufficient pump absorption. Limited by the wavelength tunable range of the ASE source, the Raman signal with a further reduced QD cannot be investigated in this experiment.
Power evolutions of (a) the 1086.5 nm signal and (b) the residual pump as functions of pump power, with different QD outputs.
Based on the comprehensive analysis, under the optimal parameters including OC reflectivity of 19% and PDF length of 400 m, with 1.29% QD, the maximal signal power achieves 47.7 W with a slope efficiency of 87.2%, and with 0.78% QD, the maximal signal power is 23.7 W with a slope efficiency of 77.0%. The results affirm that the cladding-pumped RFL based on the boson peak of PDF has great ability on low heat production, which may improve the potential on power scaling and thermal management of RFLs.
4 Conclusion
In summary, based on the boson-peak-induced Raman gain in PDF, we demonstrate the first cladding-pumped RFL with QD reduced to less than 1%. Compared with core-pumped RFLs, the cladding-pumped RFL has higher maximal signal power and larger residual pump power. The practicability and potential for the high-power and low-QD RFL are experimentally assessed and proved. In future work, we will continue to investigate the properties and improve the performances of phosphorus-doped high-power and low-QD RFLs.
Acknowledgments
The authors are grateful to Tao Wang, Yanxing Ma, Sen Guo, Weide Hong, Song Zhang and Huan Yang for their important help with this work. This work was funded by the National Natural Science Foundation of China (NSFC) (No. 61905284), the National Postdoctoral Program for Innovative Talents (No. BX20190063) and the Innovation Group of Hunan Province, China (No. 2019JJ10005).
Part of the results in this paper were presented at the Advanced Solid State Lasers Conference (ASSL, 2021).
Open access
