This paper investigates the frequency response of load modulation networks for asymmetric Doherty power amplifiers (ADPA) with an output back-off power level larger than 6 dB and a power ratio of peak to main amplifier (N − 1) larger than 1. The influence of the main path impedance transformer (IT) on the Doherty impedances at main and peak path as well as on the ADPA's efficiency is analyzed. Scaling of the main IT's characteristic impedance via ξ indicates a maximum broadband matching for an input voltage Vin of ξ · Vin,max. By weighting the frequency- and ξ-dependent efficiency curves using a probability density function (PDF), an optimum is obtained for ξ = 1/N. To verify the theory, three ADPAs with different ξ-scaled ITs are designed, measured, and compared. For the design at 3.6 GHz, a gallium nitride (GaN) transistor is used. By means of the intrinsic node matching technique, matching at the current source plane is obtained. In laboratory measurements, the ADPA with ξ = 1/N achieves a power-added efficiency (PAE) of 63% at 42 dBm output power and a PDF-weighted average PAE of 38.8% within 400 MHz bandwidth for 8 dB peak-to-average power ratio. Comparison with similar state-of-the-art ADPAs in GaN technology shows highest PAE and operation power gain GP for center frequencies larger than 3.0 GHz.

Large-signal modeling of Gallium Nitride (GaN) based high electron mobility transistors (HEMTs) demands a proper description of trapping effects. In this paper, a new, simplified yet accurate drain-lag description is proposed, enhancing the simulation accuracy and the extraction flow of the physics-based compact model ASM-HEMT. The present study investigates the impact of drain lag on specific physical phenomena, focusing on the relation between trap states, surface-potential calculations, and electron transport properties. It is supplemented with a revised extraction procedure, minimizing the required measurements, thereby the undesired consequences of several passes on the same device, using pulsed I-V and pulsed S-parameters only, and approaches for efficient and accurate simulation results. We show that the proposed trap model is a determinative tool for simulating both small and large-signal behavior predicting precisely S-parameters and load-pull performance.

A modified ant lion optimization (MALO) algorithm is proposed in this article, for the synthesis of Chebyshev-based arrays by optimizing amplitudes and phases of excitations, and element spacings. Modification in ant lion optimization is achieved by hybridizing it with chaotic particle swarm optimization. The optimization process is employed to obtain an array pattern with the least possible sidelobe level. Close-in sidelobe level minimization for optimum pattern synthesis is suggested. Instead of only steering the main beam towards the desired direction presented by some popular optimization methods, the beam steering along with null positioning in other specified direction is also achieved employing MALO. Considering the arrays with the same design parameters and the results of other optimization algorithms, the performance of MALO is evaluated. The results show that MALO provides considerable improvements in an array pattern compared to the arrays optimized using other optimization algorithms and the uniform array.

This study illustrates the dynamical reconfiguration of a concentric hexagonal antenna array radiation to generate a pencil beam and flat-top beam simultaneously by electronic control in two principle vertical planes under consideration. Both the beams share a common normalized optimal current excitation amplitude distribution while the optimal sets of phase excitation coefficients are varied radically across the hexagons to generate a flat-top beam. The proposed approach is able to solve the underlying multi-objective problem and flexible enough to the efficient implementation of additional design constraints in the considered φ-planes. In this paper, a set of simulation-based examples are presented in an integrated way. The outcomes validate the effectiveness of the stated optimization using meta-heuristic optimization algorithms (teaching–learning-based optimization, symbiotic organism search, multi-verse optimization) to reach the solution globally and prove actual relevance to the concerned applications.

In order to encrypt/encode data based on the magnitude level of the radar cross-section (RCS), we propose an approach with a precise estimation considering the resonant characteristics of a multipatch backscatter-based chipless radio frequency identification (RFID) dedicated for chipless tags depolarization. The working principle is based on the polarization mismatch between the tag and the reader antenna to control the magnitude of the backscatter, which allows a reliable detection in real environments. We introduce in this paper a new 4-bit chipless RFID tag with an enhanced RCS, based on a triangular patch antenna with multiple resonators. Additionally, we propose an ultra-wideband impulse radar (UWB-IR)-based reader that interrogates the chipless tag with a UWB pulse, and the received backscatter was studied in both time- and frequency-domains. The antenna was operating from 4.7 to 6.1 GHz, a band allocated for RFID systems. The obtained experimental measurement results in the environment of anechoic chamber were exceptionally relevant to validate the simulation results.

This paper presents a polarization-independent 11-bit chipless RFID tag based on frequency-selective surface which has been designed for encoding and relative humidity (RH) sensing applications. The 10 exterior U-shaped resonators are used for item encoding whereas Kapton has been incorporated with the interior resonator for RH sensing. This radio-frequency identification (RFID) tag operates in S- and C-frequency bands. The proposed design offers enhanced fractional bandwidth up to 88% with the density of 4.46 bits/cm2. Both single- and dual-layer tags have been investigated. The simulated results are in good agreement with measured results and a comparison with existing literature is presented to show the performance. Simple geometry, high code density, large frequency signature bandwidth, high magnitude bit, high radar cross-section, and angular stability for more than 75° are the unique outcomes of the proposed design. In addition, RH sensing has been achieved by integrating the Kapton on the same RFID tag.

This research paper introduces a ultra-wideband (UWB) multiple input multiple output (MIMO)/diversity antenna with three rejected bands using one compact electromagnetic band gap (EBG) structure. The suggested EBG structure rejects three bands at WiMAX, WLAN, and the X-band within the passband of the UWB antenna. To achieve compactness in the conventional EBG structure, two via and square slots are introduced. This structure contributes to better impedance matching by using tapered feedline and slots in the radiating patch. To improve the isolation among all four compact UWB monopoles, decoupling strips are extended from the ground plane. Furthermore, the |S21| is below 17 dB in between the antenna elements and the envelope correlation coefficient is below 0.5, which are tolerable values within the UWB range. Furthermore, different MIMO/diversity characteristics are also discussed. An FR-4 substrate with dimensions of 38 × 45 × 1.6 mm3 is used for the fabrication of the suggested structure.

A wideband staircase pattern defected ground monopole antenna integrated with an artificial magnetic conductor (AMC) reflector has been proposed for C-band (4–8 GHz) and ITU band (8.01–8.5 GHz) applications. The integrated antenna consists of a staircase antenna at top, a 2 × 2 AMC reflector at the bottom and an air substrate as gap between them. The AMC offers 18.5% ± 90° reflection phase bandwidth from 6.10 to 7.32 GHz. The AMC layer has achieved mu-negative properties in the designated band. The AMC proffers polarization independent behavior in the respective frequency band depicting robustness in AMC reflection phase characteristics. The integrated antenna has offered a wide impedance bandwidth of 2.78 GHz (42.8% at 6.5 GHz and 34.1% at 8.15 GHz) due to the defected ground monopole. The integration of wideband AMC beneath the staircase monopole antenna alters the out of phase radiation to in-phase planer pattern which enhances the peak gain up to 9.7 dB. It reduces the 1-g averaged specific absorption rate to 0.223 and 0.324 W/kg at the two designated bands. The structure maintains almost similar bandwidth and gain due to artificial human body loading.

Fifth-generation technology is not fully deployed in the world wireless communication till date. Millimeter-wave (mm-wave) band needs to be used due to plenty of available bandwidth and for achieving the goals of 5G such as greater data rate, ultra-high-speed video broadcasting, low latency services, and many more. Wideband antenna is required for 5G applications to access the high speed, low latency Internet services, and ultra-high-definition video streaming. Various bandwidth enhancement techniques have been reported by the researchers for microstrip antennas operating at microwave bands. High link losses, small wavelength, limited coverage, and environmental losses are the major challenges of mm-wave band. To mitigate these issues and satisfy 5G standard, an antenna with wide bandwidth, high gain, narrow steerable beam, high isolation, low side lobe levels, and multiband characteristics is required. Modifications in conventional antenna design techniques are required to achieve broader bandwidth along with stable radiation characteristics, improved gain, and low side lobe levels at mm-wave frequencies. This paper presents the survey of various bandwidth enhancement techniques which has been used in the 5G antennas designed by researchers. Reviews of some wideband 5G antennas with their performance comparisons are also discussed.

In this research study, a compact dual-polarized co-radiator ultra-wideband (UWB) multiple-input multiple-output (MIMO) antenna with improved impedance bandwidth and isolation is proposed for wireless applications. The designed co-radiator has an overall area of 0.3λo × 0.3λo mm2 (where, λo is free space wavelength corresponding to the lower cut-off frequency, i.e., 3.1 GHz). The proposed resonator comprises of a hybrid geometry which is created with the combinations of a circular-shaped patch, a square, and two rectangular stubs. It is centrally aligned between two 50 Ω micro-strip feed lines that are positioned orthogonal to each other. Further, the modified ground plane is attached with the end-loaded line which provides broadband isolation over entire UWB frequency band. The simulated results of the proposed antenna exhibit wideband characteristics with impedance bandwidth of 3.1–16.9 GHz with minimum isolation of −15 dB. Moreover, all the radiation performance parameters are analyzed and discussed. Some important diversity parameters such as envelope correlation coefficient, mean effective gain, effective diversity gain, and channel capacity loss have also been evaluated. Furthermore, all the measured results of proposed antenna agree well with the simulated results which make the proposed antenna a suitable candidate for UWB-MIMO wireless applications.

The design, analysis, fabrication, and testing of a four-port multiple-input multiple-output (MIMO) antenna is reported in this paper for automotive communications. The MIMO antenna is constructed using the basic antenna element exploiting a slot geometry. Two such antennas are developed on the same microwave laminate to develop a two-port MIMO antenna. Two such microwave laminates are interlocked to create the four-port MIMO scheme. The most distinct feature of the proposed architecture is that the inter-port isolation is well-taken care without the need for an external decoupling unit. The four-port MIMO antenna has an overall volume of 32 × 15 × 32 mm3. The prototype MIMO antenna is fabricated and the measurements are carried out to validate the simulation results. The antenna offers ultra-wideband (UWB) characteristics covering the frequency range of 2.8–9.5 GHz. The average boresight gain of the antenna ranges from 3.2 to 5.41 dBi with the peak gain at 8 GHz. The simulated efficiency of the antenna is greater than 73% within the operating bandwidth. The MIMO parameters such as envelope correlation coefficient, diversity gain, and mean effective gain are evaluated and presented. The appropriateness of the proposed antenna for deployment in the shark fin housing of the present-day automobiles is verified using on-car performance estimation.

This article introduces a cylindrical dielectric resonator antenna (CDRA) fed with a rhombic ring-shaped tapered feed for Multiple-Input-Multiple-Output (MIMO) applications. The proposed hybrid MIMO CDRA resonates at four frequency bands 2.5, 5.09, 6.8, and 9.0 GHz with isolation levels of 22, 34.22, 30.55, and 18.55 dB. Isolation enhancements are achieved by introducing “L” shaped slots on the partial ground plane. Parametric analysis is performed to validate the optimized dimensions of the tapered feed without and with DRA and defected ground structure. Diversity performance is examined by using envelope correlation coefficient and diversity gain. The proposed antenna operates in the S, C, and X-bands and is suitable for RF communication mobile broadband services, Wi-Fi, radar, and satellite applications. Good agreement is observed between simulated and measured results.