Introduction
Movement of dicamba herbicide from the site of application to unintended locations has become one of the most controversial and problematic issues in row-crop production in the United States (Association of American Pesticide Control Officials 2020; USEPA 2020). In 2017, an unprecedented number of herbicide injury complaints (approximately 2,700) were filed with state departments of agriculture due to movement of dicamba onto non-targeted plants (i.e., off-target movement) (Bish et al. Reference Bish, Oseland and Bradley2020). Complaints included nearly 1.5 million ha of non–dicamba resistant (non-DR) soybean [Glycine max (L.) Merr] and a variety of other plant species such as fruit and nut trees, grapes (Vitis spp.), commercial gardens, specialty crops, and residential properties (Bish et al. Reference Bish, Oseland and Bradley2020; Bradley Reference Bradley2018). This issue was the featured topic in many major news outlets (New York Times, Washington Post, Chicago Tribune, NPR, etc.). Issues were not resolved in the next growing seasons, with 1,400 and 1,345 official complaints reported to state departments of agriculture in 2018 and 2019, respectively. A significant amount of additional damage was believed to have been unreported (USEPA 2020). Many scientists referenced the injury as “landscape level,” indicating damage in many occurrences was uniform across large regions with no discernible source or gradient (Bish et al. Reference Bish, Guinan and Bradley2019b, Reference Bish, Oseland and Bradley2020). Historically, similar types of injury were referred to as “air mass damage,” which indicated a herbicide-contaminated air mass had settled across the landscape (Reisinger and Robinson Reference Reisinger and Robinson1976). In recent years, the U.S. Midsouth States has been one of the most heavily impacted areas. Other regions such as Illinois and Iowa have reported similar damage severity in recent years (Association of American Pesticide Control Officials 2020; Wechsler et al. Reference Wechsler, Smith, McFadden, Dodson and Williamson2019). This sudden increase in injury complaints correlated with development and commercial release of dicamba-resistant (DR) cotton (Gossypium hirsutum L.) and soybean.
DR crops were developed to provide producers with chemical options for control of broadleaf weed species in broadleaf crops and to provide control of glyphosate-resistant weeds. Weeds are the most problematic biological threat to crop yield loss in global agricultural production, and they greatly influence humanity’s ability to produce food, fiber, and fuel (Hildebrand Reference Hildebrand1946; Oerke Reference Oerke2006). Proliferation of herbicide-resistant (HR) weed species has resulted in a substantiated appreciable threat to agricultural production worldwide (Gould et al. Reference Gould, Brown and Kuzma2018; Hicks et al. Reference Hicks, Comont, Coutts, Crook, Hull, Norris, Neve, Childs and Freckleton2018; Palumbi Reference Palumbi2001). A primary method by which agricultural seed and chemical manufacturers have responded to the issue of weed resistance is by genetically engineering crops to withstand currently registered herbicides, such the development of DR cotton and soybean (Behrens et al. Reference Behrens, Mutlu, Chakraborty, Dumitru, Jiang, LaVallee, Herman, Clemente and Weeks2007; Nandula Reference Nandula2019). Dicamba is a synthetic auxin herbicide (WSSA Group 4) that has been used for more than 50 yr to control broadleaf weeds in pastures, turf, and cereal crops (Shaner Reference Shaner2014) and has a low frequency of weeds evolving resistance compared with other herbicides of similar age (Heap Reference Heap2021). DR cotton and soybean were commercialized by 2016; however, dicamba could not legally be applied to crops until 2017 (Bish et al. Reference Bish, Farrell, Lerch and Bradley2019a).
Historically, dicamba formulations were subject to volatility (evaporation from the leaf or soil surface) and could be transported to off-target locations (Behrens and Lueschen Reference Behrens and Lueschen1979; Egan and Mortensen Reference Egan and Mortensen2012). Consequently, two new dicamba formulations were developed concurrently with the DR cotton and soybean trait to reduce volatility. These new formulations are the only dicamba products approved for use in DR cotton and soybean (Macinnes Reference Macinnes2016; Xu et al. Reference Xu, Cannan, Finch, Schnabel, Bratz, Bowe and Brommer2012). The first independent studies to evaluate these new dicamba formulations showed that volatility was reduced compared with older formulations, but still occurred (Bish et al. Reference Bish, Farrell, Lerch and Bradley2019a; Jones et al. Reference Jones, Norsworthy, Barber, Gbur and Kruger2019; Mueller and Steckel Reference Mueller and Steckel2019). Dicamba has been shown to volatilize from both products in detectable amounts for up to 96 h after application (Bish et al. Reference Bish, Farrell, Lerch and Bradley2019a).
Other factors that have contributed to the millions of hectares of off-target dicamba injury include physical drift of herbicide droplets due to wind during the application; spray equipment contamination with herbicide remnants; and use of older, unapproved, more-volatile dicamba formulations. Many broadleaf plant species such as non-DR soybean, peaches [Prunus persica (L.) Batsch], grapes, and others are highly sensitive to very low doses of dicamba. Only a small amount of this herbicide needs to volatilize and redeposit on sensitive soybean for injury symptoms to occur (Al-Khatib et al. Reference Al-Khatib, Parker and Fuerst1992, Reference Al-Khatib, Parker and Fuerst1993; Al-Khatib and Peterson Reference Al-Khatib and Peterson1999; Andersen et al. Reference Andersen, Clay, Wrage and Matthees2004; Dintelmann et al. Reference Dintelmann, Warmund, Bish and Bradley2020; Egan et al. Reference Egan, Barlow and Mortensen2014; Kniss Reference Kniss2018; Solomon and Bradley Reference Solomon and Bradley2014).
Once herbicides enter the atmosphere they can exist in the gaseous or particulate-bound phase and, in either phase, are subject to wet and dry deposition (Glotfelty and Caro Reference Glotfelty and Caro1975; Majewski Reference Majewski1996). Pesticides are typically detected in higher concentrations during intensive agricultural production seasons and at locations with high usage of pesticides (Goolsby et al. Reference Goolsby, Thurman, Pomes, Meyer and Battaglin1997; Hatfield et al. Reference Hatfield, Wesley, Prueger and Pfeiffer1996; Hill et al. Reference Hill, Harker, Hasselback, Moyer, Inaba and Byers2002; Richards et al. Reference Richards, Kramer, Baker and Krieger1987). However, data are lacking on meteorological conditions associated with pesticide deposition from the atmosphere and whether pesticides deposited from the atmosphere occur at sufficient concentrations to cause injury to sensitive species. Therefore, the objectives of this study were to analyze dicamba concentrations in bulk deposition samples, survey producers to understand what regions are applying the most dicamba, develop models that identify atmospheric variables associated with weekly and seasonal dicamba flux, and identifiy the conditions most likely to result in increased dicamba deposition and potential injury to sensitive plants.
Materials and Methods
Sampling Locations and Description of Weather Stations
Samples from the accumulated water collection from the prior week were collected from 12 geographically distinct locations in Missouri (Figure 1). Sampling locations were positioned in regions of Missouri where row-crop agricultural production of corn (Zea mays L.), soybean, and/or cotton occur, except one location at Cook Station, MO. This location is in the Missouri Ozark Region, and less than 500 ha of row-crop production occurs annually in this county. The site was selected as a negative control and to provide an understanding of the extent of long-distance dicamba transport. Samplers were placed farther than 365 m away from the nearest possible source of dicamba (corn, soybean, or cotton field) to avoid possible contamination from droplet drift. Each sampling location was in close proximity (<100 m) to a weather station owned and maintained by the University of Missouri. Meteorological data were collected in 3-s increments and averaged into 5-min means. Instrumentation utilized included a Vaisala/Campbell Scientific air temperature/relative humidity probe (model HMP60-L1-PT, Logan, UT) at 305 cm above ground level (AGL) and a three-cup anemometer for wind speeds at this same height. Weather stations contained rainfall gauges that allowed for monitoring of precipitation. A subset of weather stations were equipped to monitor for temperature inversions with Vaisala probes at 46 and 168 cm AGL. Information on the inversion monitoring stations and weather station maintenance protocols can be found in Bish et al. (Reference Bish, Guinan and Bradley2019b).
The geographic distribution of bulk atmospheric deposition sampling sites in Missouri in 2019 and 2020. Color-coded counties indicate the adoption of dicamba-resistant soybean in each county. Numbers correspond to sampling locations in Table 1.
Sampler Design
Design of deposition samplers was derived and modified from Waite et al. (Reference Waite, Sommerstad, Grover, Kerr, Westcott and Irvine1995). The deposition pan was a 100 by 100 cm aluminum sheet gently curved to slope toward a 2.5-cm center opening. The pan was secured to a wooden frame at 121 cm AGL, and the wooden frame was secured to the ground using 60-cm metal stakes. Once the pan was positioned, a plastic funnel attached to a 60-cm polycarbonate tube was secured directly beneath the center opening of the deposition pan. The tube was then inserted into the 2.5-cm opening of a 22.7-L glass carboy housed within the wooden frame. All rainwater from each 7-d sampling period drained through the center opening and was stored in the carboy until the weekly collection occurred. Each carboy could store up to 5 cm of rainfall. On weeks when high rainfall amounts occurred, the overflow was not collected. Metal siding was secured on all four sides of the wooden frame to shade the sample and prevent photolysis of dicamba. Funnels, polycarbonate tubes, and carboys were replaced each season.
Sample Collection
Sample collection began April 22, 2019, and April 13, 2020. Each week and at each location, 1 L of water from the glass carboy was collected in a plastic bag. On weeks when <4 mm of rainfall occurred, dry deposition was collected by adding 1.9 L of distilled water across the deposition pan. On weeks when >4 mm of rainfall occurred, the deposition pan was not rinsed. Justification for this approach stems from previous research. This methodology prevents further dilution of samples by introducing additional purified water (Farenhorst et al. Reference Farenhorst, Andronak and McQueen2015; Waite et al. Reference Waite, Sommerstad, Grover, Kerr, Westcott and Irvine1995, Reference Waite, Cessna, Grover, Kerr and Snihura2004). The majority of herbicide has been shown to deposit from the wet portion, with the dry deposition contributing only marginal amounts (Dämmgen et al. Reference Dämmgen, Erisman, Cape, Grünhage and Fowler2005; Epple et al. Reference Epple, Maguhn, Spitzauer and Kettrup2002). Following weekly collection, each carboy was replaced with a clean carboy. Sample collection occurred through the peak pesticide application season until September 9, 2019, and September 7, 2020, similar to previous studies on herbicide deposition (Scheyer et al. Reference Scheyer, Morville, Mirabel and Millet2007; Waite et al. Reference Waite, Sommerstad, Grover, Kerr, Westcott and Irvine1995). Samples were collected weekly by a trained group of individuals who were careful to avoid any contamination from clothing, skin, or other equipment. Upon arrival at each site, water samples were transferred immediately from the collection carboy before any additional cleaning or maintenance of the collector to ensure no unintended dicamba residues could be introduced into the sample. Field blanks were included weekly to monitor contamination. Following collection, samples were transported to a freezer and stored in the dark at −5 C until analysis, which occurred <4 mo after collection. Weekly and cumulative season dicamba flux (in µg m−2) were computed using sample volume, dicamba concentration in the rainfall, and area of the deposition pan.
Dicamba Extraction, Quantification, Quality Control, and Assurance
A solid-phase extraction (SPE) method utilizing straight barrel anion exchange cartridges (Bond Elut SAX SPE 500 mg, 6 ml; Agilent Technologies, Santa Clara, CA) was used to extract dicamba. SPE columns were conditioned with 5 ml of MeOH followed by 5 ml of 0.1 M NaCl solutions followed by 5 ml of deionized water each. All solvents were high-performance liquid chromatography (HPLC) grade. From each rainwater sample, a 200-ml portion was extracted by the SPE columns at a flow rate of 10 ml min−1. Ultra-pure N2 gas (99.99%) was used to dry the column for 10 min. The SPE cartridge was eluted with 5 ml of NH4OH at 10 ml min−1 and collected into glass test tubes. Between each sample, SPE lines and plungers were cleaned with MeOH and deionized water. Collection tubes containing SPE processed samples were concentrated to dryness using ultra-pure N2 gas at 30 C and then reconstituted using 0.5 ml of MeOH, resulting in a 400-fold concentration from the original sample.
Dicamba concentrations were quantified using an HPLC with a photodiode-array detector (Shimadzu Nexera XR 20A, Shimadzu USA Manufacturing, Columbia, MD) and external standard calibration. Compound separation was achieved using a Zorbax Eclipse XDB-C18 column (narrow bore 2.1 by 250 mm, 3.5 µm, Agilent). Mobile phases consisted of 0.1% phosphoric acid and 100% acetonitrile pumped at isocratic flow rates of 0.24 and 0.16 ml min−1. The column oven temperature was set to 40 C, and the injection volume was 5 µl. Dicamba was detected at 205 nm. The retention time under these conditions was 4.20 (+ 0.11) min. Calibration standards included in each HPLC run ranged from 5 to 1,000 µg L−1 using analytical grade (>95%) standards of each compound (Sigma Aldrich, St. Louis, MO). Positive detections were based on retention time and match to reference spectra of dicamba obtained from 500 µg L−1 standards. Reference spectra were obtained at 1-nm increments from 190 to 400 nm and a scan interval of 240 ms. Spectral matches were based on a Similarity Index feature in the instrument software, which is scaled from 0 to 1, with 1 representing a perfect fit to the reference. For these analyses, the Similarity Index was set to 0.95 as a screening threshold and ≥0.98 for positive identification. Based on the latter criteria, the instrument detection limit for dicamba was 5 µg L−1, resulting in a method detection limit of 0.0125 µg L−1 on a water basis. Quality control and assurance of HPLC and SPE runs were achieved by including blank HPLC-grade methanol standards on a routine basis to confirm prevention of cross-contamination or errors in sample labeling or placement. Spiked field samples were included at 1 µg L−1 to determine dicamba recoverability throughout the experiment. Recovery of dicamba in spiked samples ranged from 88% to 104%. No corrections to data were made based on these recoveries. An additional screening confirmed photolysis and microbial degradation of dicamba did not influence the results of this study. Any analyte concentrations that exceeded the linear calibration range of the HPLC were diluted 5:1 methanol to sample and were reanalyzed.
Soybean Response to Dicamba-contaminated Rainfall Events
Soybeans were exposed to simulated rainfall events contaminated with dicamba. Dicamba-sensitive soybean seeds (‘Pioneer P44A37L’) were grown in blow-molded plastic pots measuring 19 by 17 m (3.8 L Custom-Tainer 400C, Hummert International, Earth City, MO). Pots were filled with 3 kg of an 80:20 ratio of field soil:commercial potting medium (Pro-Mix with mycorrhizae, Premier Tech Horticulture, Quakertown, PA). Commercial potting medium was necessary for adequate porosity, root development, and water infiltration. Seeds were planted to a 1.9-cm depth. Plants were maintained in a greenhouse at 30 C and watered daily. Natural light was supplemented with metal-halide lamps (600 µmol m−2 s−1). Treatments were applied when soybean reached the V3-V4 stage of growth (approximately 13 to 17 cm in height). Simulated rainfall events were applied using 3.8-L handheld polyethylene adjustable pressure garden sprayers, which were exchanged between treatments to avoid contamination. Each sprayer contained an adjustable nozzle orifice, which allowed for extremely coarse droplet sizes to simulate rainfall droplets. Treatments included 1, 10, 100, 1,000, 10,000, and 100,000 µg L−1 of the commercially available DGA (diglycolamine salt of dicamba) plus VaporGrip® dicamba formulation (XtendiMax®, Bayer Crop Science, Creve Coeur, MO). The rates of 1,000, 10,000, and 100,000 µg L−1 were purposely exaggerated and are substantially higher than any detections from the study. Treatments included single-application treatments and sequential-application treatments that simulated repeated exposure to dicamba in consecutive weeks as was observed in data collected from the rainfall deposition study. For the 1, 10, and 100 µg L−1 dicamba treatments, the sequential applications occurred either one or both 1 and 2 weeks following initial application. Before all applications, pots were weighed to ensure each pot maintained the same field water capacity. A 1-min simulated rainfall event was applied to achieve the same amount of water as a 1.3-cm rainfall event. A 35-cm-tall plastic cone was positioned on the inner edges of the pot to force water droplet contact with either soybean plant tissue or the soil surface. This application allowed for tissue and root uptake of dicamba solution, similar to a rainfall event. A plastic collection container was placed under each pot to contain any water that leached through the soil column following treatment application. No additional water was applied for 24 h after treatment. Once supplemental watering was reinitiated, care was taken to ensure field capacity of the soil was not exceeded. This was accomplished by weighing pots 1 h after saturation to determine field capacity and then ensuring pots were not watered to exceed that weight. This process was repeated in the same manner for sequential-application timings. Treatments were arranged in a completely randomized block, and plants were allowed to grow for 14 d following the final sequential treatment. At that time, a previously characterized rating scale was utilized to assess visual soybean injury from dicamba (Behrens and Lueschen Reference Behrens and Lueschen1979). This experiment was repeated once to result in two experimental runs. Visual injury data were subject to ANOVA using PROC GLIMMIX in SAS (SAS v. 9.4, SAS Institute, Cary, NC) and means were separated using Fisher’s protected LSD (P < 0.05).
Survey to Determine the Adoption of DR Technology by Missouri Soybean Producers
Herbicide usage data at the county level were not accessible for both years of this research; therefore, an external survey method was utilized to collect information on adoption of DR technology in each sampling region of Missouri. Previous research showed that surveying agricultural professionals that routinely make crop seed and herbicide decisions can provide useful and accurate information (Bish and Bradley Reference Bish and Bradley2017; Werle et al. Reference Werle, Oliveira, Jhala, Proctor, Rees and Klein2018). The survey was distributed via email to all certified pesticide applicators in Missouri and consisted of two questions: (1) In which county or counties do you apply pesticides or influence pesticide application decisions? (2) What percentage of soybean planted in (2019/2020) do you estimate contained the dicamba-resistant trait (0–100%)? There were 1,107 total survey responses in 2019 and 432 responses in 2020. Results of the survey are shown in Figure 1 and Table 1. County-level usage data from 2019 (https://water.usgs.gov/nawqa/pnsp/usage/maps/county-level) align well with the results from this survey (R2 = 0.83).
Dicamba mass flux in Missouri bulk atmospheric deposition samples in 2019 and 2020
a Weekly max.: the weekly maximum dicamba flux in bulk deposition samples for each year; (wk): week of sampling in which the weekly maximum occurred.
b Cumulative dicamba flux for the entirety of the sampling season.
c Percentage of weeks throughout sampling periods each year when detectable amounts of dicamba occurred.
d Dicamba-resistant soybean adoption as determined by survey described in “Materials and Methods.”
e Numbers in parentheses correspond to the location of sampling sites shown in Figure 1.
Determination of Factors Influencing Atmospheric Deposition of Dicamba
Regression analyses were conducted to identify relationships between dicamba flux and factors that influence deposition. Two analyses were conducted. The first was to identify factors that may influence cumulative dicamba deposition over the entire growing season. The second was to identify factors that may influence weekly dicamba flux in regions with high DR trait adoption and higher dicamba detections throughout the growing season. Independent variables included in the first analysis were: percent DR soybean trait adoption in the county where sampling occurred (derived from previously described survey), percentage of sampled period in which wind speeds were <4.8 km per hour (kph), percentage of sampled period in which daily high temperatures exceeded 29 C, and average relative humidity for the sampled period. Wind speed and temperature thresholds were selected based on requirements within the approved dicamba herbicide labels and because previous research showed each factor to influence either dicamba volatility or particle suspension in air (Bish et al. Reference Bish, Farrell, Lerch and Bradley2019a; Egan and Mortensen Reference Egan and Mortensen2012; Hill et al. Reference Hill, Harker, Hasselback, Moyer, Inaba and Byers2002; Oseland et al. Reference Oseland, Bish, Steckel and Bradley2020). The analysis was conducted using PROC REG in SAS v. 9.4 with a stepwise selection. A priori significance levels selected for entry and removal from the model were P ≤ 0.15, as this threshold has been found to improve the model and provide further predictive ability (Shtatland et al. Reference Shtatland, Cain and Barton2001). Dicamba fluxes were subject to PROC UNIVARIATE to test for normality conditions, and a logarithmic transformation was necessary to achieve normalized distributions. Models were considered significant at P ≤ 0.05.
The second regression analysis utilized weekly meteorological data from the Heyward and Charleston sampling locations in southeastern Missouri. These locations had the highest DR trait adoption in both 2019 and 2020 and had consistent and substantial dicamba deposition through most of the growing seasons. Conditions for entry and removal from the model as well as model and variable significance criterion were identical to those described for the first regression analysis. However, data before May 1 and following July 15 were excluded for practical reasons. Dicamba labels restrict use after July 15. We also removed weeks in which <1 ppb of dicamba was detected. Independent variables included average daily high temperature for the week, midday wind speeds (1200 to 1600 hours), average weekly relative humidity, and weekly frequency of inverted temperature conditions. Temperature inversion conditions were met once air temperatures at 305 cm AGL exceeded air temperatures at 46 cm AGL by 0.5 C or more, as described previously in Bish et al. (Reference Bish, Guinan and Bradley2019b). Unfortunately, the Senath, MO, location could not be included in the analysis, as routine quality-control assessments of the weather data generated from this station indicated biases in probes and resulted in faulty temperature inversion data.
Results and Discussion
We detected dicamba in deposition samples from each of the 12 locations in both 2019 and 2020, with the exception of the Cook Station site in 2019. Cook Station has little to no DR soybean or cotton (Figure 1) and fewer than 1,000 ha of total agricultural row-crop production (USDA-NASS 2019). Detected concentrations varied among locations and years. The highest concentration detected in 2019 was in southeast Missouri at the Senath site and occurred on June 3 (84 µg L−1; Figure 2; Table 1). The highest concentration detected in 2020 was also in southeast Missouri at the Charleston site and occurred on April 30 (37 µg L−1; Figure 2). Weekly detection frequency ranged from 21% to 95% in 2019 and from 26% to 89% of the sampled weeks in 2020 (Table 1). For both years, the highest mass fluxes on a weekly and annual bases occurred at the three sites in southeast Missouri (Sites 3, 8, and 9; Figure 1). These sites had peak weekly fluxes >140 µg m−2, with the highest weekly mass flux in 2019 observed at Portageville (Site 8) on June 3 (1,098 µg m−2; Table 1) and the highest in 2020 at Senath (Site 9) on May 4 (354 µg m−2, Table 1).
Weekly dicamba concentrations in bulk atmospheric deposition samples in 2019 and 2020. Color-coded symbols correspond with dicamba-resistant soybean adoption levels depicted in Figure 1. Sampling began April 22, 2019, and April 13, 2020. Cook Station was not included in the figure.
Cumulative dicamba flux over the growing season illustrated the timing of dicamba deposition (Figure 3). High flux periods were observed throughout the growing season of both years, particularly at the three southeast Missouri sites, which had multiple high weekly deposition events (>100 µg m−2) and high cumulative fluxes over both growing seasons (Figure 3). Cumulative flux primarily increased until herbicide applications diminished in early July. All other sites had peak flux events of <20 µg m−2, but several sites (2, 4, 5, 6, 7, 10, and 11) had at least 1 yr with cumulative growing season fluxes >25 µg m−2. At the three southeast Missouri sites, annual variation in cumulative flux showed that dicamba deposition in 2019 was dominated by a few large events, while in 2020 deposition occurred via multiple, smaller events. Typically, dicamba applications occur either before planting in April or after crop emergence in June. Although other authors have reported patterns of greater herbicide concentrations in the atmosphere during intensive application periods (Dubus et al. Reference Dubus, Hollis and Brown2000; Waite et al. Reference Waite, Sommerstad, Grover, Kerr, Westcott and Irvine1995), the flux data presented here indicated consistent dicamba application occurred at several sites from April to July. Overall, these results demonstrated that dicamba was commonly deposited from the atmosphere during the growing season, and observed deposition and fluxes were strongly related to DR soybean adoption near collection sites and the timing of rainfall events (Figure 3; Table 1).
Cumulative dicamba mass flux in 2019 and 2020. Line colors are in accordance with dicamba-resistant soybean in Figure 1. Week 1 sampling began April 22, 2019, and April 13, 2020. Cook Station was not included in the figure.
Simulating Dicamba-contaminated Rainfall Events
Results from the simulated rainfall assay revealed that soybean exposed to dicamba concentrations of 10 µg L−1 or less in one simulated rainfall event showed minimal symptoms of visible injury (<1%; Figure 4). However, repeated simulated rainfall events with at least 10 µg L−1 dicamba resulted in more prominent injury symptoms. Soybean treated with 10 µg L−1 dicamba in two consecutive weeks had 7% visible injury symptoms, while soybean treated with 10 µg L−1 dicamba in three consecutive weeks had 16% injury. There were multiple weeks in southeast Missouri when >10 µg L−1 of dicamba was collected in the bulk deposition samples (Figure 2; Table 1). A concentration of 10 µg L−1 simulated at 1.3 cm would be equivalent to a 47.2 µg m−2 deposition event in our study. Others have reported repeated exposures over time increase the likelihood of dicamba symptomology on sensitive soybean plants when dicamba is in the air (Zaccaro-Gruener et al. Reference Zaccaro-Gruener, Norsworthy, Brabham, Barber, Roberts, Mauromoustakos and Mueller2023). Thus, it is plausible that rainfall is transporting dicamba from the atmosphere in sufficient concentrations to contribute to the dicamba injury observed on sensitive plant species like non-DR soybean in regions where landscape-level injury has been reported.
The response of dicamba-sensitive soybean to simulated dicamba-contaminated rainfall events. Sequential treatments were applied 1 wk apart to simulate repeated exposure to dicamba in sequential weeks. These treatments are indicated by fb (= followed by). The treatments of 1,000 ppb and above were to simply elicit a response and were exaggerated beyond any measurements of dicamba recorded in this study. The severity of injury was based on previously reported 0% to 100% scale to measure visible symptoms of dicamba injury on soybeans. Bars include data compiled from two experimental runs, and ratings were taken 14 d after the final sequential treatment
Identifying Variables That Contribute to Dicamba Deposition
Finally, we utilized two separate stepwise linear regression models to determine the influence of seasonal environmental conditions and regional DR soybean adoption on dicamba deposition. The first model was based on cumulative dicamba flux over the growing season to identify factors that influenced deposition differences among the locations (Table 2). Adoption of DR soybean and the percentage of the growing season when wind speeds were ≤4.8 kph were selected in the regression model (R2 = 0.71). The most influential factor was DR trait adoption (R2 = 0.65), and this factor was positively correlated with dicamba fluxes. DR soybean adoption was >85% for both years in the three southeast Missouri counties where dicamba fluxes were highest. While dicamba applications do not occur on every hectare with DR technology, a previous Nebraska survey showed that approximately 80% of growers who planted soybean with the DR trait made an application of dicamba to their soybean (Werle et al. Reference Werle, Oliveira, Jhala, Proctor, Rees and Klein2018). Others have found similar positive correlations of atmospheric deposition and pesticide usage within a region (Hill et al. Reference Hill, Harker, Hasselback, Moyer, Inaba and Byers2002).
Results of stepwise linear regression modeling to determine the influence of seasonal environmental conditions and soybean trait adoption on cumulative dicamba flux in bulk atmospheric deposition samples in Missouri. a
a Stepwise linear regression included all data from all sampling sites except Cook Station due the inconstancies of soybean production in this region compared with other sites.
b Adoption is the percent adoption of dicamba-resistant soybean in the county where sampling occurred based on survey results from Missouri pesticide applicators and influences.
c Low wind indicates the percentage of the sampling season that wind speeds reached speeds of 4.8 kph or less.
The influence of wind speed and atmospheric stability on dicamba flux was evaluated further in an additional stepwise linear regression analysis to identify regional-specific factors (R2 = 0.41; Table 3). The best-fit model indicated that weekly dicamba flux was influenced by wind speeds during the middle of the day, the percentage of the week in which inverted temperature conditions occurred, and relative humidity. Inversion frequency and humidity were positively correlated with dicamba flux, while midday wind speeds were negatively correlated. Wind speed is highest at midday and equates to a larger boundary layer, which is the layer of atmosphere in which airborne particles are trapped (Hu Reference Hu, North, Pyle and Zhang2015; Majewski and Capel Reference Majewski and Capel1995). A larger boundary layer allows more area for volatilized particles to disperse. This result builds upon the previous stepwise analysis and provides additional support for the role of stable atmospheric conditions and atmospheric water vapor on dicamba behavior in the atmosphere. These results are similar to findings from Bish et al. (Reference Bish, Farrell, Lerch and Bradley2019a) demonstrating that stable air (i.e., low wind and/or inversions) and higher dew point temperatures (i.e., the temperature at which air is saturated with water) correlated with increased dicamba deposition following dicamba applications. Dew point temperatures are dependent upon variables including relative humidity and increase as relative humidity increases (Lawrence Reference Lawrence2005). Increases in volatilization of pesticides from soil due to increased relative humidity have been observed previously (Davie-Martin et al. Reference Davie-Martin, Hageman, Chin, Rouge and Fujita2015; Farha et al. Reference Farha, Abd El-Aty, Rahman, Shin and Shim2016). Previous research has shown that stable and humid conditions can restrict dispersion of atmospheric particulates (Yin and Wang Reference Yin and Wang2017). Others have hypothesized that high humidity could increase the settlement of dicamba across a region (Egan and Mortensen Reference Egan and Mortensen2012) Lower wind speeds and shrinking of the atmospheric boundary layer associated with stable conditions are likely two impediments to dispersion. It was previously speculated that stable and humid conditions could interfere similarly with atmospheric dicamba dispersion (Bish et al. Reference Bish, Farrell, Lerch and Bradley2019a). Any impediment that prevents dicamba molecules from dispersing could result in concentrated masses of dicamba being readily available for deposition when weather conditions change. A similar mechanism was described by Peterson et al. (Reference Peterson, Paulus and Foley1969) in research focused on air pollution. Robinson and Fox (Reference Robinson and Fox1978) coined the phrase “air mass damage” in the 1960s to describe a similar phenomenon of large-scale deposition events for a synthetic auxin herbicide in Yakima Valley, WA.
Results of stepwise linear regression modeling to determine the influence of weekly environmental conditions on dicamba flux in bulk atmospheric deposition samples in Missouri. a
a Stepwise linear regression included 2019 and 2020 data from the Portageville and Charleston Missouri locations where the highest dicamba-resistant soybean adoption occurred during both years of the study.
b % Inversion indicates the percentage of the sampled week that temperature-inverted conditions occurred.
c MidWind is the average middle of the day (1200–1600 hours) wind speed at the sampling locations.
d Humidity is the average relative humidity for the week.
Research on dicamba applications at the farm level have resulted in models that associate stable air with an increased likelihood of dicamba moving off-target, as stable air masses are commonly pushed to new locations by gentle horizontal winds (Bish et al. Reference Bish, Oseland and Bradley2020; Oseland et al. Reference Oseland, Bish, Steckel and Bradley2020). However, to our knowledge, this study is the first to measure dicamba deposition from the atmosphere and correlate those levels directly to atmospheric stability.
Movement of dicamba herbicide from the site of application to non-target areas has been a significant problem in the agricultural industry since the introduction of DR crops in 2016 (Bish et al. Reference Bish, Oseland and Bradley2020). The term “landscape-level injury” has been used to describe the observed dicamba injury in southeast Missouri, northeast Arkansas, western Tennessee, Illinois, and Iowa (Hartzler Reference Hartzler2017). Understanding the factors that influence atmospheric dicamba transport and deposition is critical to the responsible use of DR technology, and we used data collected in Missouri to serve as a case study for what may also be occurring in other states with high injury occurrences. We determined that dicamba concentrations detected in bulk deposition samples in southeast Missouri exceeded any reported concentrations in the historical literature (Dubus et al. Reference Dubus, Hollis and Brown2000; Waite et al. Reference Waite, Sommerstad, Grover, Kerr, Westcott and Irvine1995). At three sites, dicamba deposition was sufficient to cause injury to sensitive plant species like non-DR soybean, with repeated high-deposition events occurring annually. Similar results were observed by Zaccaro-Gruener et al. (Reference Zaccaro-Gruener, Norsworthy, Brabham, Barber, Roberts, Mauromoustakos and Mueller2023). Dicamba fluxes at these sites also showed high levels of deposition from April to July each year, which were apparently sustained by widespread dicamba usage during these months. From this research, our models indicate that the adoption of DR soybean and stable atmospheric conditions are two of the most important factors that influence the amount of dicamba deposition. This research is the first to illustrate that dicamba can be deposited from the atmosphere at levels sufficient to cause injury to sensitive soybean and that regional DR soybean adoption and stability of the atmosphere are important in determining those concentrations.
Airborne pesticides need wind to disperse. Previous research has found that daily wind speeds in southeast Missouri tend to be lower than in other regions within the state as well as many other regions throughout the United States where dicamba injury has not been as widespread (Pfleeger et al. Reference Pfleeger, Olszyk, Burdick, King, Kern and Fletcher2006). This same research has shown that other geographies with a high frequency of off-target injury, such as areas throughout Illinois and Arkansas, are also prone to less-windy conditions (Pfleeger et al. Reference Pfleeger, Olszyk, Burdick, King, Kern and Fletcher2006). Our study did not investigate the usage of DR soybean in these regions, but they are known high soybean-producing regions, and some estimates indicate high DR adoption at the time of this research (Wechsler et al. Reference Wechsler, Smith, McFadden, Dodson and Williamson2019).
At two of three sites in southeastern Missouri, dicamba deposition and fluxes were lower in 2020 than in 2019 (Table 1). A combination of factors may have influenced these observed differences. There were 10 fewer fieldwork days over the duration of our sampling period in 2019 compared with 2020 (USDA-NASS 2020). As DR soybean adoption did not differ in this region between years, it is possible that dicamba applications occurred within a shorter time period in 2019 and resulted in higher deposition compared with 2020, when applications were spread out over more days (Figure 3). Additionally, the U.S. Court of Appeals for the Ninth Circuit interrupted dicamba applications during 2020 due to legal uncertainties involving dicamba label registrations. It is unknown to what extent this affected applications of dicamba in 2020.
The deposition of dicamba via rainfall and dry deposition has broad implications for soybean production regions across the United States. The observed dicamba deposition (Figure 2) was indicative of two main transport patterns: (1) sites with high concentrations were indicative of local transport (<1 km) during or soon after periods of dicamba application combined with high usage; and 2) sites with consistent but low dicamba deposition events throughout the sampling period indicated the potential of medium- to long-range transport (>1 km) or limited dicamba usage near these sites (Scheyer et al. Reference Scheyer, Morville, Mirabel and Millet2007). The results presented are supported by work from Zaccarro-Gruener et al. (2023), who measured dicamba in deposition samples in Arkansas. This work also identified decreased concentrations in days following rain events, indicating rain clears the atmosphere and corresponds to the dicamba detection events observed in our study (Figures 2 and 3). However, this study did not utilize atmospheric stability or wind speeds to correlate dicamba concentrations. This research has highlighted the potential for landscape-level injury to occur to highly sensitive plant species like non-DR soybean from contaminated rainfall events and identified certain factors such as high DR trait adoption and stable atmospheric conditions that likely contribute to atmospheric deposition of dicamba. This research indicates that in some regions of the United States, dicamba can be used for weed management in DR crops without significant concern for atmospheric deposition. However, in other regions, atmospheric stability and increased dicamba usage as a result of high DR trait adoption is likely causing atmospheric deposition that results in injury to a variety of agricultural, ornamental, and tree species.
Acknowledgments
The authors would like to thank Gatlin Bunton, James Heiser, and Delbert Knerr for assistance with sample collection. This research received no specific grant from any funding agency or the commercial or not-for-profit sectors. The authors have no conflicts of interest to declare.
Open access
