Contact angles of glycerol and diiodomethane drops were measured on the surface of kaolin pellets covered with different amounts of dodecylamine chloride (DDACl) to as much as one monolayer. For a glycerol drop, the contact angle changed from 25.7° (bare surface) to 45.4° for the surface precoated with 0.125 monolayer of DDACl, but remained nearly constant above this level up to one monolayer. For a diiodomethane drop, the contact angle changed from 28.6° (bare surface) to 58.1° for one DDACl monolayer precoating. Using these contact angles and a modified Young equation, the dispersive and nondispersive components of the surface free energy of DDACl-covered kaolin were calculated. These data showed that in the extreme case (one monolayer) the dispersive component was reduced by the DDACl from ∼36 mJ/m2 (bare surface) to 25.4 mJ/m2, i.e., the value characteristic for paraffin (25.5 mJ/m2); however, the nondispersive component was not reduced to zero. A minimum value (15.83 mJ/m2) was determined for the sample covered with 0.125 DDACl monolayer (calculated), and a slight increase in the nondispersive component was observed for greater coverages. Such a change of the nondispersive component suggests that, at higher coverages, some adsorbed DDACl molecules were oriented with their polar ends off the surface. Based on the values of the γsfd and γsfn, the work of water spreading was calculated. This work was positive for the bare surface (32.8 mJ/m2) and methanol-treated (36.5 mJ/m2) kaolin surface, but negative for 0.125 DDACl monolayer precoating (-31.1 mJ/m2). It remained essentially unchanged for higher coverages. These data mean that bare and methanol-treated kaolinite surfaces were hydrophilic and that DDACl-treated surfaces were hydrophobic.

The electrostatic lattice energy of polar phyllosilicates can be calculated when a correction term Ecorr equal to -2πμ2/V is taken into account, where μ is the dipole moment of a slice d(001) and V is the molecular volume. The interlayer bonding energy can be obtained by Giese's method, if the energy of separation of the layers over a distance A is plotted againts 1/[d(001) + Δ]. Thus, for a polar chlorite the interlayer bonding energy is 69.8 kJ/unit cell. Using the Madelung method, the interlayer bonding energy of slices of kaolinite having a thickness of d(001) is 84 kJ/mole. Similarly the interlayer bonding energy of slices having a thickness d(020) is 2520 kJ/mole. To avoid the instability of the outer slices of the crystal caused by the cooperating dipole moments of all slices, the hypothesis was made that the atoms have in reality reduced charges and that the charge reduction is such that the dipole moment becomes zero. The adopted charges lower the interlayer bonding energy to as little as 14 kJ/mole. The interlayer interaction of slices of fluorkaolinite with thickness d(001) is repulsive. Crystals of a polar chlorite must be bounded either by incomplete hydroxide layers or by layers onto which charge-compensating anions are adsorbed. Polarity makes cleavage in chlorite more difficult.

Alumina is produced from bauxite, which contains a mixture of various oxides, such as aluminum (Al), iron (Fe), silicon (Si), and titanium (Ti). Bauxite can also be considered a source of several other valuable metals, such as scandium (Sc), vanadium (V), and gallium (Ga). The composition and mineralogy of alumina determine their economic value, but their characteristics vary by locality. The physicochemical characteristics of bauxites can also be influenced largely by weathering processes, even within the same locality. For this reason, the present study was undertaken with the objective of comparing the characterization data of three bauxite samples collected, which will be referred to as D, E, and F, from the Cruz Alta do Pará plateau in northern Brazil. The samples were solubilized by multi-acid digestion and fusion with lithium metaborate to quantify their metal compositions by inductively coupled plasma optical emission spectrometry (ICP-OES). The mineralogical characterization was conducted by X-ray diffraction (XRD), and the phase changes of minerals in bauxite were detected by thermogravimetric analysis (TGA/DTG). The total organic carbon (TOC) technique was used to quantify the C in the samples, and the moisture content was also measured. Alumina was 30 wt.% on average for all samples, good for producing high-purity alumina by hydrometallurgical processes. The results, however, showed high (~20 at.%) silica concentrations in two samples and ~3 wt.% Fe in one sample, which can pose a challenge in the Bayer process. The X-ray diffraction (XRD) analysis showed that gibbsite (Gbs), kaolinite (Kln), anatase (Ant), and hematite (Hem) were the major mineral phases in these samples. The study showed that the samples from the same mine vary in their metal content, especially with regard to Si, and they, thus, need to be processed selectively to maximize their economic value.

X-Ray powder diffraction and thin section analyses indicate that marginal lacustrine mudstones of the Green River Formation in the south-central Uinta basin, Utah, contain abundant analcime. The analcime has a low Si/Al ratio (<2.31) and occurs as very fine grained disseminated crystals and, to a lesser extent, as coarser-grained pore-filling cement. Analcime-rich mudstones and associated sandstones, siltstones, and carbonates lack volcanic detritus and zeolites other than analcime, thus making it difficult to support the concept that the analcime formed from precursor zeolites derived from volcanic glass altered in saline, alkaline-lake water. Abundant dolomite, syneresis cracks, and the absence of freshwater pelecypods and gastropods suggest that the lake (Lake Uinta) was moderately saline and alkaline. The restricted illite-illite/smectite clay mineral suite in the analcime-rich mudstones suggests that detrital clays significantly altered in a moderately saline and alkaline environment, thereby providing a source of Si and Al for the formation of analcime.

Red mudstones contain twice as much analcime as green mudstones (14 vs. 7 wt. %). Green mudstones have a day mineral suite consisting of illite (44 wt. %), mixed-layer illite/smectite (35 wt. %), smectite (12 wt. %), and minor kaolinite (4 wt. %) and chlorite (5 wt. %), whereas red mudstones have a more restricted day mineral suite consisting ofillite (68 wt. %) and mixed-layer illite/smectite (26 wt. %) with very minor smectite, chlorite, and kaolinite. Periodic minor fluctuations in lake level probably exposed large areas of shallow lacustrine-interdistributary green mud. Evaporative pumping on the exposed mudflats concentrated the moderately saline and alkaline-lake water, thereby producing Na-rich brines that enhanced the formation of analcime by accelerating the alteration of detrital clays and, perhaps, other minerals. Oxidation of iron from altered iron-bearing minerals stained the analcime-rich mud red with iron hydroxide or oxide (perhaps hematite). The overall reaction from green to red mud (mudstones) was probably: detrital phyllosilicates + Na-brine + iron-bearing minerals + oxygen → analcime + iron hydroxide or iron oxide.

A vermiculite-aniline intercalate with a basal spacing of 14.78 Å was investigated by one- and two-dimensional X-ray diffraction methods. The intercalate, prepared by ion exchange between Na-saturated vermiculite from Llano, Texas, and a 1% aniline hydrochloride solution, contains only one aniline cation per single layer cell. A reduced effective cell-charge is believed to be responsible for this. Structure factor calculations were made in space group C2/c and with unit cell dimensions of a = 5.33, b = 9.18, c = 29.78 Å, and β = 97.0°. However, extra reflections in the a*b* plane, which are similar to those in a vermiculite-benzidine intercalate, showed that after aniline intercalation the true unit cell became primitive. The aniline cations are distributed statistically over equivalent crystallographic sites in the interlayer space. The organic molecules are orientated with their planes vertical and their nitrogen atoms over the projected centers of the ditrigonal cavities into which they key. The aniline cations form ordered arrays upon the silicate layers by packing into rows. Perpendicular to [010], populated and vacant rows alternate. Along populated rows aromatic ring planes are alternately parallel and perpendicular to [010]. With small adjustments this model is similar to that of benzidine-vermiculite.

The vitric matrix of pre-caldera acid tuff and tuff breccia of the Santorini volcano, Aegean Sea, Greece has been generally replaced by one or more of the following authigenic minerals: K-rich and (K,Ca)-rich clinoptilolite, mordenite, opal-CT, and clay minerals. Halite is also present in some samples. Initial compositional inhomogeneities between the dacitic blocks in tuff breccia and tuff seem to have controlled the type of K-rich heulandite-group zeolite that formed. Mordenite postdates the heulandite-group zeolites and opal-CT. Some mordenite has replaced the rims of glass shards. The alteration minerals are not related to vertical or lateral zonation, and the irregular distribution of their assemblages is attributed to variations in heat flow, ionic activity in interstitial waters, and permeability. The pyroclastic rocks were in a region of active heat flow during and after their emplacement. The formation of authigenic silicates may have led to the sealing of open spaces and fractures, imposing barriers to permeability and subdividing the original open system into smaller closed systems. As alteration progressed, some of the trapped water in each individual domain was consumed in hydration reactions. Salts could have been concentrated by such a process, and halite probably precipitated from solutions of appropriate composition in the individual closed systems.

Smectite with polyvalent cations on the exchange complex readily absorbed riboflavin from aqueous solution to a limit of about 0.5 mmole/g. The shape of the adsorption isotherms was of the Langmuir type. An exception was Na+-smectite which provided an S-shaped isotherm and smaller amounts of adsorption. Ca2+-vermiculite had no interlamellar adsorption of riboflavin, suggesting that this mineral does not swell sufficiently to permit such adsorption. Adsorption isotherms, X-ray powder diffraction data, and UV-visible spectroscopic data suggest that the mechanisms of interaction between smectite and riboflavin may involve a combination of ion-dipole, charge transfer, hydrogen bonding, and physical effects.

The cult of Zhunti 准提/準提 (Sanskrit: Cundī) is a unique religious and cultural phenomenon in China. However, the scholarship devoted to its history has long been dominated by two problematic models—the model of ‘Sinification’, according to which the goddess Zhunti is a Chinese Buddhist deity borrowed from an Indian source, and the ‘evolution’ model that depicts the persistence of the Zhunti cult as a continuous and gradual process. I challenge these views and instead argue that, far from being a foreign transplant, Zhunti is a deity ‘made in China’ and there is no evidence of continuity in the development of the cult from the Liao to Ming–Qing times. To justify these assertions, I re-examine the development of the cult of Zhunti by exploring its vicissitudes throughout history and highlighting the ‘Chinese creations’ that were produced during the process of the making of the goddess Zhunti.

High-resolution transmission electron microscopy (HRTEM) and electron diffraction experiments have been performed on R1 and R> 1 illite/smectite (I/S) samples that from X-ray powder diffraction (XRD) experiments appear to contain well-ordered layer sequences. The HRTEM images confirmed earlier computer image simulations, which suggested that periodicities due to I/S ordering can be imaged in TEM instruments of moderate resolution. The experiments also confirmed that in instruments of this sort, the strongest contrast arising from the compositional difference between I and S layers occurs under rather unusual imaging conditions of strong overfocus. Some selected-area electron diffraction (SAD) patterns showed additional diffraction spots consistent with R1 and R3 ordering. SAD patterns and cross-fringes arising in HRTEM images from non-00l reciprocal lattice rows indicated that the stacking vectors of most adjacent 2:1 layers were not randomly oriented with respect to each other. Thus, the I/S was not fully turbostratic, but instead consisted of very thin, coherently stacked crystallites that extended across the fundamental particles postulated by Nadeau and coworkers.

S/(I + S) ratios were determined for about seventy HRTEM images obtained and interpreted by three different TEM operators. These ratios were consistent with those obtained from standard XRD procedures, suggesting that results obtained by XRD can be used to infer the initial structural state of mixed-layer I/S prior to treatment of samples for XRD experiments. The HRTEM experiments thus demonstrated that the two specimens examined consisted of ordered I/S existing as small crystals, most of which contained more layers than the fundamental particles of Nadeau and coworkers. The non-turbostratic stacking suggests an energetic interaction between the individual fundamental particles, leading to at least two alternative thermodynamic descriptions of these materials. Although the I/S crystals in the present experiments probably were disaggregated into fundamental particles during sample preparation for XRD, the I/S crystals appear to have separated only along the smectite interlayers. If the term “fundamental particle” is to be used for primary, untreated I/S, its original definition should be modified to include not only free particles, but also those that occur as layers within small crystals. It further should be recognized that these particles can interact thermodynamically and crystallographically with their neighbors.

X-ray powder diffraction studies were performed with propyl-, dodecyl-, and dodecyldiam-monium bentonites saturated with aqueous mixtures of eleven organic pollutants at concentrations of 0.01 to 100%. The alkylammonium salt treatment separated the montmorillonite unit layers, which increased the interlamellar volume and exposed the interlamellar surfaces for adsorption of the organic pollutants. Washing the salt-treated clays with distilled water removed excess, physically adsorbed alkylammonium ions that could interfere with adsorption of the organic pollutants. Adsorption isotherms conducted at organic pollutant concentrations of 100 and 1000 mg/liter indicated the three alkylammonium montmorillonites, especially propylammonium montmorillonite, were effective adsorbents from aqueous solution, but to a lesser extent than adsorbents currently used in the water and wastewater fields.

Ash layers from Searles Lake, California, were sampled in core of drill hole KM-3, which penetrated 693 m of lacustrine sediment deposited in a playa-lake complex over the past 3.2 my. Lake water changed from moderately saline and slightly alkaline (pH ~7.5) to highly saline 2.04 my ago and to highly saline and alkaline (pH ~9.5) 1.28 my ago. As a result of brines flushing downward, the upper 291 m of sediment, spanning the past 1.28 my, contain highly saline, alkaline pore fluid. Silicic ash layers in contact with highly saline, alkaline pore fluid were first altered to phillipsite and meriinoite and then to K-feldspar and searlesite. The transformation of phillipsite and/or meriinoite to K-feldspar required more than 45,000 years and was largely completed in 140,000 years. Tephra layers in contact with moderately saline, slightly alkaline pore fluid vary from uncemented vitric ash containing minor smectite to bentonites in which glass is wholly altered to smectite, clinoptilolite, analcime, and opal. Layers with much fine tephra are more altered than the coarser, better-sorted layers. Alteration is attributed to hydrolysis in essentially a closed hydrologic system, in which the alteration of glass to smectite raised the pH, aSiO2, and (Na+ + K+)/H+ activity ratio to the level where clinoptilolite formed. Some diffusion and/ or fluid flow is, however, indicated by the loss of SiO2 during the alteration of ash layers to smectite and by anhydrite deposited during and after clinoptilolite in some tuffaceous sandstones.

Quaternary debris flows derived from ophiolite melange in northern Southland, New Zealand, are locally cemented and veined by cross-fiber and fine-grained chrysotile. Chrysotile was identified by optical, X-ray powder diffraction, electron microprobe, differential thermal (DTA), and infrared analysis methods. Microprobe and DTA also suggested the presence of as much as 6% of sub-microscopic, noncrystalline alumina, probably in the form of pseudoboehmite. Cavity fillings and irregular veins containing chrysotile are as thick as 40 cm and commonly contain lizardite clasts. Calcite commonly accompanies chrysotile as a vein mineral. Magnetite and pyrite are found near and adjacent to chrysotile veins. These accessory minerals imply that the chrysotile formed under alkaline, reducing conditions. Surface water seepages have pH = 9. Remnant debris-flow topography, Holocene radiocarbon dates, and the absence of hot spring activity confirms that chrysotile can form under near-surface, low-temperature conditions. Growth of chrysotile fibers on a lizardite substrate suggests that the chrysotile formed by solution of detrital lizardite and subsequent precipitation in cavities within the debris flow.

The influence of adsorbed H+, Na+, K+, Ca2+, Mg2+, Ba2+, and Al3+ ions on the wettability of a kaolinite surface was determined from contact angles, which were measured in kaolinite-water drop-air (saturated water vapor) and kaolinite-diiodomethane drop-air systems. From the results and using a modified Young equation, the dispersion and nondispersion components of the free energy of the kaolinite hydrated surface were determined. The dispersion component of all the tested samples was between 32.8 and 38.9 mJ/m2, but the nondispersion component changed almost linearly from 53 to 95.9 mJ/m2 with the change of the entropy of hydration of the adsorbed ions, except for K+ and Ba2+. The latter ions were exceptions, probably due to their large ionic radii.

The adsorption and reaction of thiophene and methylthiophenes in the interlayer of Cu2+- and Fe3+-montmorillonites were investigated by resonance Raman spectroscopy. Thiophene and 3-methylthiophene polymerized to form cations of polythiophene and polymethylthiophene respectively, which were characterized by absorption bands in the near-infrared region. These polymer cations formed in the interlayer were reduced to their neutral polymers if the clay-polymer complexes were in contact with water, and the formation of their neutral polymers was clearly demonstrated by their resonance Raman spectra. 2,5-Dimethylthiophene in which polymerization was hindered by methyl substitution at the 2 and 5 positions, was oxidized to 2,5-dimethylthiophene cation in the interlayer.

Reaction of hydroxy-Al oligocations with Ce3+- and La3+-exchanged montmorillonites, using 1.25, 1.60, or 2.0 mmole Al/g smectite, yielded partially pillared hydroxy-Al montmorillonite products containing a significant concentration of residual Ce3+ or La3+. After heat treatment at 250°C these products showed high surface areas (∼340–500 m2/g) and high basal X-ray powder diffraction spacings (18.0–18.6 Å). Calcination at 400°–700°C resulted in lower surface areas of ∼200–450 m2/g and basal spacings of 16.3–18.3 Å, the values showing a gradual decrease with a decrease in the Al/smectite weight ratio and/or increase in the heat-treatment temperature. A major modification and improvement in the cross-linking procedure was achieved by fast aging (6–48 hr) of the hydroxy-Al oligomeric solution at 95°–100°C, instead of conventional aging for 2–3 weeks at 25°C.

Fluorinated NH4+-montmorillonites, containing 0.4 to 2.1 wt. % F, were prepared by reaction of NH4+-montmorillonite at 60°C with 1.0 to 3.0 N aqueous solutions of NH4F. Interaction of the fluorinated montmorillonites with hydroxy-Al oligocations, using a ratio of 2.0 mmole Al/g smectite, yielded a series of cross-linked fluorinated montmorillonites with basal spacings of 17.9–18.0 Å and surface areas of 180–325 m2/g after heat treatment at 250°C. Calcination at 400°–500°C resulted in lower d(001) (16.6–17.7 Å) and surface-area values (140–300 m2/g). Increase in the fluorine content caused gradual decrease in both values. Transmission electron microscopy of pillared Ce-montmorillonite showed a highly oriented network of well-separated, parallel unit layers with an interlayer distance, Δd(001), of 9–10 Å. Calculated lateral (interpillar) distances were in good agreement with the pore-size distributions determined in independent adsorption studies.