Photovoltaics are expected to play an important role in the future energy infrastructure. However, achieving simultaneously high efficiency in both light absorption and carrier collection remains a challenging tradeoff. Photon management, which refers to the engineering of materials and device structures to control the spatial distribution of optical energy, offers a number of promising routes to optimizing this tradeoff. Progress in fabrication of nanostructured materials combined with advances in the understanding of nanophotonic devices has enabled new strategies for photon management in a range of photovoltaic devices. Prominent among these are structures with pronounced surface topography or graded refractive-index profiles that reduce surface reflectivity; materials processing that increases optical absorption in materials such as silicon; incorporation of semiconductor nanostructures that enables simultaneous improvements in optical absorption and photogenerated carrier collection; and coherent light trapping in optical waveguide modes via plasmonic or optical scattering effects. The articles in this issue review some of these emerging directions.

To harness the full spectrum of solar energy, optical reflections at the surface of a solar photovoltaic cell must be reduced as much as possible over the relevant solar spectral range and over a wide range of incident angles. The development of antireflection coatings embodying omni-directionality over a wide range of wavelengths is challenging. Recently, nanoporous films, fabricated by oblique-angle deposition and having tailored- and very low-refractive index properties, have been demonstrated. Tailorability of the refractive index and the ability to realize films with a very low-refractive index are properties critical in the performance of broadband, omnidirectional antireflection coatings. As such, nanoporous materials are ideally suited for developing near-perfect antireflection coatings. Here, we discuss multilayer antireflection coatings with near-perfect transmittance over the spectral range of 400−2000 nm and over widely varying angles of acceptance, 0−90°. The calculated solar optical-to-electrical efficiency enhancement that can be attained with nanoporous multilayer coatings over single-layer quarter-wave films is 18%, making these coatings highly attractive for solar cell applications.

We describe two ways in which pulsed lasers can be used to increase efficiency in photovoltaic devices. First, pulsed-laser hyperdoping can introduce dopants into a semiconductor at non-equilibrium concentrations, which creates an intermediate band in the bandgap of the material and modifies the absorption coefficient. Second, pulsed-laser irradiation can enhance geometric light trapping by increasing surface roughness. Hyperdoping in silicon enables absorption of photons to wavelengths of at least 2.5 μm, while texturing enhances the absorptance to near unity at all absorbing wavelengths. This article reviews both effects and comments on outstanding questions and challenges in applying each to increasing the efficiency of photovoltaic devices.

Well-ordered arrays of one-dimensional semiconductors, such as titania nanotubes (NTs), have attracted attention as a promising new film architecture for dye- and semiconductor-sensitized solar cells. The film architecture in sensitized solar cells combines light absorption, charge injection, and charge-carrier transport to generate electrical power and is, therefore, a key component in determining the photoconversion efficiency of a cell. Because of the arrays’ distinct combination of physical, electrical, and optical properties, the conversion efficiencies of TiO2 NT-based devices are rapidly catching up with those of the traditional nanoparticle-based cells. In this article, we briefly review the fabrication and morphology of the NT arrays and discuss the strong influence that the film architecture and individual NT structure exert on the light-harvesting and charge-collection properties of sensitized solar cells. Besides affecting the solar conversion efficiency, the morphological and electrical properties of the arrays also impact the cell fabrication process.

Thin-film photovoltaic technologies have an enormous potential to reduce the cost of solar electricity. However, because thin photoactive layers are used, optical absorption is incomplete unless light-trapping strategies are employed. Since conventional light-trapping approaches based on geometric scattering are less effective in thin-film cells, coherent light-trapping approaches that exploit the wave nature of light are being explored to enhance optical absorption. In this article, we look at the various strategies for coherent light trapping in thin-film solar cells, including photonic crystals, metal nanostructures, and multilayer stacks. The suitability of a particular strategy depends on factors such as configuration of the solar cell, process compatibility, cost, desired angular response, and materials usage. We also discuss the physical limits of light trapping in thin films.

In recent years, there has been rapid development in the field of nanoscale light trapping for solar cells. This has been driven by the decrease in thickness of solar cells in order to reduce materials costs, as well as advances in fabrication technology and computer power for simulating nanoscale structures. Nanoscale light trapping offers the possibility of enhancing absorption beyond the limits achievable with geometrical optics for certain structures. It also allows the optical design to be separated from the electrical design, as for example in plasmonic solar cells. Most importantly, thin-film cell designs will need to incorporate nanophotonic light trapping in order to reach their ultimate efficiency limits. In this article, we review the major types of nanophotonic light trapping, including plasmonic, diffraction gratings, and random scattering surfaces and describe the major advantages and disadvantages of each. In addition, we describe the most important related fabrication and characterization technologies and provide an outlook on future directions in this field.