A highly efficient design procedure for dielectric-loading multi-band coaxial-type feed antennas is proposed in this paper. Cylindrical modal matching method is employed for generalized scattering matrix calculation inside the feed, while spherical wave expansion is adopted for the feed aperture discontinuity in consideration of the outer shape. Closed-form scattering matrices with respect to different junctions help realize higher computational efficiency than the full-wave simulation solvers, and thus enable rapid optimization in terms of various electrical functional requirements across multiple frequency bands simultaneously. A Ku/Ka multi-band feed is investigated as a numerical example. Excellent radiation performances, including the low cross-polarization level, constant beamwidth, stable phase center, high return loss, and high isolation between bands of interest are achieved by employing multi-scalar rings, dielectric loading, and a three-port hybrid junction. The design is validated by experimental results from a manufactured prototype. Good consistency confirms the accuracy of our numerical approach, and demonstrates the proposed feed a good candidate for Ku/Ka-band satellite communication antenna systems.

This paper presents a second-order tunable single-ended (unbalanced) bandpass filter (BPF) with continuous 0.4–3-GHz coverage and a tunable balun BPF with continuous 1.1–1.7-GHz coverage for software-defined radio transceivers with the use of band-switchable and radio frequency (RF)-micro-electromechanical systems (MEMS)-tuned resonators. The BPFs are realized with two pairs of RF switches for coarse-tuning and RF-MEMS-tunable capacitors for fine-tuning. On the one hand, for the tunable single-ended BPF, a transition between three bands is enabled using two pairs of RF switches. On the other hand, for the tunable balun BPF, a transition between two bands is enabled using one pair of RF switches. Furthermore, the three-band switchable single-ended BPF is constructed in a nested two-filter bank structure for expanding the tuning range without increasing the footprint. In addition, to complement the discrete band gaps, RF-MEMS capacitor-tuned resonators are used, and a continuous tuning range of nearly the entire ultra-high-frequency band is achieved. The filter bank is fabricated on a Duroid substrate with εr = 3.5 and h = 0.787 mm. The filter bank has an insertion loss of 3.2–6.8 dB and a 1-dB bandwidth of 65–450 MHz with a continuous tuning range of 0.4–3 GHz.

Synthesis of differential-mode bandpass filter (BPF) with good common-mode suppression has been described and demonstrated on the basis of ring dielectric resonator (RDR) for high-performance communication system. A RDR with two pairs of feeding lines has been used to excite TE01δ-mode. This unique combination of feeding lines and the ring resonator creates a differential passband. Meanwhile, TM01δ-mode of the DR can also be excited to achieve common-mode rejection in the stopband. Transmission zeros are created in the lower and upper stopband to further improve the selectivity of the proposed BPF. A second-order differential BPF is designed, fabricated and its performance is measured to validate the concept. There is good agreement between simulated and measured results.

With the increasing demand of millimeter-wave (MMW) communication, the performance of its frequency synthesizer has high requirements. In this paper, a multiple conversion mechanism, which used hybrid frequency synthesis technique is presented. Some key modules include linear frequency-modulated generator, agile, and low phase noise local oscillators (LOs), automatic gain control, receiver front-end circuit, and MMW LO circuits are discussed and simulated to verify correctness of the mechanism. The experimental results show that, spurious is better than −65 dBc, phase noise is no more than −80 dBc/Hz@1 kHz, and the maximum frequency-hopping time is <1.8 µs.

In through-the-wall radar imaging, multipath propagation can create ghost targets, which can adversely affect the image reconstruction process. However, unlike genuine targets, ghost positions are aspect-dependent, which means their position changes with the transceiver location. This paper proposes efficient ghost suppression methods exploiting aspect dependence feature under compressive sensing framework. This paper proposes a generalized signal model that accommodates for the reflections of the front-wall and target-to-target interactions, making the scheme more practical, yet the knowledge of the location of reflecting geometry is not a requirement as in most of the recent literatures. In addition, the sensing matrix is greatly reduced making the methods more attractive. Moreover, this paper investigates the influence of array configurations by examining two antenna array configurations: multimonostatic, and single-view bistatic configurations. Results based on synthesized data and real experiment show that the proposed method can greatly suppress multipath ghosts and hence increase signal-to-clutter ratio.

This paper presents the design of a size miniaturized and harmonic suppressed wideband double-section rat-race coupler (RRC). Series and shunt stepped-impedance transmission line units are proposed to replace the quarter wavelength transmission lines in the conventional design of wideband (50% fractional bandwidth) two-stage rat-race coupler. Design equations are derived using the lossless transmission line model. The proposed double-section RRC occupies only 14% area of the conventional coupler, with good return loss and isolation performances. In addition, the full-wave simulation and measured responses exhibit harmonic suppression up to at least fifth harmonic. The proposed design can be easily implemented using the standard printed circuit board etching process without any via-holes, bonding wires, and lumped elements, which make it very useful for wireless communication systems

By introducing an L-shaped metal plate connecting with the spiral monopole antenna, a planar compact ultra-high-frequency (UHF) tag antenna for radiofrequency identification system is proposed. With the overall antenna size of only 13 × 9 × 1.6 mm3, the proposed tag antenna provides the measured impedance bandwidth of 12 MHz to comply with Taiwan UHF operating band (922–928 MHz). The measured peak gain and antenna efficiency are approximately −1.1 dBi and 27% for Taiwan UHF band, respectively. Meanwhile, the measured reading distance can approach 250 m. Good tag sensitivity is obtained across the desired frequency band.

A novel planar printed phase shifter design is proposed in this paper. The design is developed with microstrip–conductor-backed coplanar waveguide– microstrip (MP–CBCPW–MP) transition line with different defected ground structures (DGS). The differential phase shift can be controlled by altering the DGS dimensions. Three prototypes with DGS dimensions 5 × 10, 10 × 20, and 10 × 30 mm2, are employed at the finite ground plane to achieve 5°, 20°, and 30° shift in phase respectively and are validated with the phase delay relation. The prominent effect of the transition region is to confine the field area. The resonance is at 700 MHz with a bandwidth of 400 MHz (0.4–0.8 GHz). The proposed phase shifter can be used for broadcasting applications. The proposed MP–CBCPW–MP transition phase shifter design with DGS is simulated, fabricated, and measured to analyze its performance.

In this paper, a three layered stacked circularly polarized rectangular dual band microstrip antenna with a defected ground structure (DGS) and a feed network with stub (showing dual wideband characteristic) is designed, fabricated, and tested for WLAN, Zig bee, Wi-Max, and IMT band applications. The proposed antenna is fabricated on an FR4 substrate with dielectric constant (εr) of 4.4; tanδ of 0.0024 and a height of 1.57 mm.The antenna has a surface area of 4.8 × 4.1 cm2 and a total height of 5.1 mm. The designed antenna covers two wireless bands from 2.39 to 2.64GHz and 3.39–3.76 GHZ with impedance bandwidths (VSWR < 2) of 250 MHz (9% bandwidth centered at 2.515 GHz) and 370 MHz (10% bandwidth centered at 3.57 GHz), respectively. This antenna is capable of covering IEEE 802.11b/g/n standards of WLAN from 2.4 to 2.485 GHz, bluetooth applications from 2.4 to 2.483 GHz, ZigBee applications from 2.4 to 2.485 GHz, IEEE 802.16/ Wi-MaX applications from 3.4 to 3.69 GHz and international mobile telecommunications (IMT) band from 3.4 to 3.6 GHz. As the antenna is circularly polarized, the misalignment of the receiver with transmitter does not affect the performance of the system. The antenna designing was done using CST MWS V'10 and the prototype of the designed antenna was tested for the validation of S11 (dB) and gain results against the simulated ones experimentally. The proposed antenna shows a gain of 4.08 dBi at 2.5 GHz and a gain of 5.024 dBi at 3.51 GHz.

Active electronically scanned array (AESA) radar has large number of transmit/Receive (T/R) modules which require multiple microwave and digital signals. Distribution of these signals through conventional method such as coaxial cable, twisted pair, etc. not only introduces engineering complexities and signal loss but also have limitation of bandwidth, data rate, transmission distance, etc. This paper addresses design and implementation of microwave photonic network for distribution of microwave and digital signals over single optical fiber using wavelength division multiplexing for AESA radars. The design challenge is to limit the variation in output radio frequency power within ±1 dB over full operational band of radar from 2 to 4 GHz and functionality under hostile military environment. Optical amplifiers have been used in all channels to stabilize optical output independent of wavelength with automatic light control. The optical signal is split into 64 identical parts to feed multiplexed signal into different digital receivers physically spread across the antenna array. It is an additional challenge to normalize performance as all 64 receivers show variation in output in spite of identical electronic circuitry. Experimental results validate the feasibility of microwave photonic network for wide branching distribution of multiple microwave and digital signals for AESA radar.

An ultra-wideband (UWB) highly compact bandpass filter with extremely high passband bandwidth is presented. The proposed structure is made using three-staged stepped-impedance lines and a composite right/left-handed transmission line (CRLH-TL) synthesized with meander fractal like ring slot in the ground and series capacitive gap in conductor strip. The capacitive gap in conductor strip and meander fractal like ring slot in the ground plane play major role for controlling the lower and higher cut-off frequencies. The equivalent circuit model of proposed filter is demonstrated and lumped parameters are extracted. A prototype is fabricated to experimentally validate the performance of proposed filter. The proposed UWB filter has extremely wide −10 dB return loss passband bandwidth from 3.14 to 18.26 GHz with relative bandwidth of 142% and insertion loss better than 0.5 dB. Also it achieves a wide upper-stopband from 19.7 to 24.4 GHz with insertion loss better than 13.0 dB, return loss <1.5 dB and sharpened rejection skirts outside the passband at both lower and upper frequency ends. Good agreement is found between simulated and measured results with measured group delay variation in the passband <0.65 ns.

The well-known range-Doppler coupling property of the chirp radar makes it more vulnerable to different types of deceptive repeater jammers that benefit from the pulse compression processing gain of the radar-matched filter. These jammers generate many false targets that appear before and after the true target. Therefore, the radar cannot distinguish the true target from the false ones. This paper reviews different self-protection repeater jammers and presents their pros and cons, in order to provide a reference for the study of jamming/anti-jamming methods.

Multifunction radars based on active phased arrays are well known and widely studied systems. The concepts of bistatic architecture, conformal array and digital beam forming (DBF) are combined in this paper to define a novel multifunction radar for point defense. The conical shape of the antenna overcomes the significant limitations in the azimuth coverage of 360° of fixed-faces phased arrays due to the beam scanning up to 45°. The usage of separate transmit/receive arrays and the DBF technique adds the operational flexibility and the possibility of multiple simultaneous functions, with an optimal time-energy resources exploitation. After a short description of its technological demonstrator, some significant design trade-off, and operating aspects of the proposed architecture, called d-Radar, are described, showing the main differences with respect to the classical, four faces, and phased-array multifunction radar architecture. It is described how the operating modes can be made more and more similar to a “staring” or “ubiquitous” radar permitting an instantaneous detection and location of short-range, low-elevation targets for sea and ground operations. Finally, some remarks about the resources management and scheduling are shown with the results from a case of study.

Different configurations of leaky-wave antennas (LWAs) based on graphene metasurfaces are studied. The electronic properties of a graphene metasurface in the low THz range are investigated in details in order to discuss the reconfigurability features of the presented structures. Simple exact formulas for evaluating the ohmic losses related to the surface plasmon polariton (SPP) propagation along a suspended graphene sheet, and the relevant figures of merit of SPP propagating over a generic metasurface are given. Such formulas allow us to explain the low efficiency of reconfigurable antennas based on SPPs along graphene metasurfaces. Then, the radiative performance and relevant losses of graphene Fabry–Perot cavity antennas (FPCAs) based on non-plasmonic leaky waves (LWs) are investigated and compared with previous solutions based on SPPs. In particular, a single-layer structure, i.e. a grounded dielectric slab covered with a graphene metasurface, and a multilayered structure, i.e. a substrate–superstrate antenna in which the graphene metasurface is embedded at a suitable position within the substrate, are considered in detail. The results show that the proposed LW solutions in graphene FPCAs allow for considerably reducing the ohmic losses, thus significantly improving the efficiency of the proposed radiators.

This paper presents an extension of the formulation of wave propagation in transverse electric (TE) and transverse magnetic (TM) modes in the case of metallic circular waveguides filled with anisotropic metamaterials. The determined higher-order modes have been analyzed and exploited to the design of filters. Among the particularities of anisotropic material, the backward waves can propagate below the cut-off frequency. The numerical results for TE and TM modes have been compared with theoretical predictions. Good agreements were obtained. We analyzed a periodic structure containing waveguides filled with anisotropic metamaterial using the mode-matching technique. By using modal analysis, our approach reduced considerably the computation time compared to HFSS.

The paper presents a two-dimensional (2D) extended envelope memory polynomial model for concurrent dual-band radio frequency (RF) power amplifiers (PAs). The model is derived based on the physical knowledge of a dual-band RF PA. The derived model contains cross-modulation terms not included in previously published models; these terms are found to be of importance for both behavioral modeling and digital predistortion (DPD). The performance of the derived model is evaluated both as the behavioral model and DPD, and the performance is compared with state-of-the-art 2D-DPD and dual-band generalized memory polynomial (DB-GMP) models. Experimental result shows that the proposed model resulted in normalized mean square error of −51.7/−51.6 dB and adjacent channel error power ratio of −63.1/−63.4 dB, for channel 1/2, whereas the 2D-DPD resulted in the largest model error and DB-GMP resulted in model parameters that are three times more than those resulted with the proposed model with the same performance. As pre-distorter, the proposed model resulted in adjacent channel power ratio of −55.8/−54.6 dB for channel 1/2 and is 7–10 dB lower than those resulted with the 2D-DPD model and 2–4 dB lower compared with the DB-GMP model.

A coplanar waveguide-fed planar hexagonal monopole ultra-wideband antenna with dual-band rejection characteristics is proposed in this paper. The desired notch frequencies at 3.5 and 5.5 GHz are realized by incorporating mushroom structures. The input impedance and surface current distributions are used for analysis and explanation of the effects of mushroom cells. The prototype and proposed antennas are fabricated and tested. From the measured results, the proposed antenna provides an operating band of 2.81–14.32 GHz for 2 ≤ voltage standing wave ratio (VSWR), while the dual-band stop function is in the frequency bands of 3.3–3.7 GHz and 5.10–5.88 GHz. Moreover, the antenna model also exhibits constant group delay and linear phase in the pass band. The proposed antenna has appreciable gain and efficiency over the whole operating band except the notch bands.

The growing demand for communication systems requires multi-channel solutions. However, the number of antennas in communication systems is dictated by the number of channels in each system which is limited by the available space on a broadcasting platform and by the limited available resources. We have developed a Multi-Channel Phase Control coupler in the VHF frequency range enabling a reduction in the number of antennas to a third of the original setup. The system is based on a phase shifter in a meander stripline geometry connected to each channel individually. The channels are then phase matched simultaneously to a single antenna through a computer-controlled capacitor bank connected to each phase shifter. The system performance shows a low insertion loss of 0.5 dB and a low return loss of −15 dB for the multi-channel setup.

A novel uniplanar wideband magneto-electric dipole antenna element is proposed in this paper. The proposed antenna is composed of the conventional bow-tie radiation patch as an electric dipole, a semi-circular loop, which works as a magnetic dipole, a coplanar ground plane, two directors with different lengths for enhancing gain, and a microstrip-to-coplanar stripline transition balun. The designed antenna adopts a small-size coplanar ground plane to achieve a uniplanar structure. Consequently, this method reduces the space size immensely and makes the antenna suitable for the array application. In addition, a tapered slot structure is utilized to improve impedance matching. The prototype of the proposed antenna was fabricated and measured. The measured results keep in good accordance with the simulated ones. The simulated results show that the proposed antenna obtains a broad impedance bandwidth of 60.5% from 2.25 to 4.20 GHz (voltage standing wave ratio [VSWR] ≤ 2) which can be applied for wireless local area network (WLAN) (2.4–2.484 GHz), worldwide interoperability for microwave access (WiMAX) (2.5–2.69/3.4–3.69 GHz), and long term evolution (LTE) (2.5–2.69 GHz). Meanwhile, the stable gain, low cross-polarization, stable unidirectional radiation patterns, and low back lobe are obtained within the operating frequency band. The array composed of the proposed antenna elements is also investigated in this paper.

The design of a novel microstrip ultra-wideband (UWB) bandpass filter with quad narrow notched-band functionality is presented. The filter consists of a multi-mode resonator (MMR) constituted from two modified stepped-impedance stubs that generate six resonate modes, five of which are within the UWB passband where the sixth mode is used to extend the upper stopband of the filter. Two transmission zeroes are located at the 3-dB edge of the passband to enhance the filter's selectivity with a skirt factor of 0.955. The MMR is fed through asymmetric interdigital coupled-lines feed to produce controllable notched-band. Additional notched-bands are generated with a parasitic coupled line. The notched-bands are centered exactly to eliminate interference at 5.2 GHz (wireless local area network (WLAN)), 5.8 GHz (WLAN), 6.8 GHz (radio-frequency identification), and 8 GHz (X-band). Good agreement is obtained between simulation and measurement results. The highly compact filter has dimensions of 8.0 × 9.83 mm2.