Small luminescent Y2O3:Eu3+ particles were prepared by a hydrothermal method first, and then, Y2O3:Eu3+/C3N4 nanocomposites were further prepared by a chemisorption method. The luminescent Y2O3:Eu3+/C3N4 nanocomposites are not only a promising down-conversion luminescent material, but also it could be used to improve the efficiencies of dye-sensitized solar cells (DSSCs). Especially, the morphology of Y2O3:Eu3+ has great influence on the performance of DSSCs. Compared with Y2O3:Eu3+ nanorods, the introduction of small Y2O3:Eu3+ particles into the cells is conducive to the improvement of cell efficiency. The efficiencies of TiO2-Y2O3:Eu3+–C3N4 composite cells were not only higher than those of pure TiO2 cells but also higher than those of TiO2-Y2O3:Eu3+ or TiO2-C3N4 composite cells, resulting in the enhancement of the average efficiency of the TiO2-Y2O3:Eu3+–C3N4 composite cell from 7.16% to 8.14%, with 14% improvement over the pure TiO2 cell. The enhancement of the efficiency can be attributed to the synergetic effect of small Y2O3:Eu3+ particles and C3N4.

In this report, a facile system consisting of iron (III) meso-tetrakis(4-hydroxyphenyl)porphyrin-methylene blue dye hybrid immobilized on a disposable paper strip was used to detect and sense H2O2 in aqueous solutions via a low-cost pixelometric imaging technique. The new technology was employed to evaluate the level of H2O2 in a self-administering 30%-labeled commercial H2O2 disinfectant solution. The result showed that the concentration of H2O2 in the tested pharmaceutical sample solution deviated from the label by 92.37%. The current approach provides a simple low-cost resolution for the rapid detection and quantification of H2O2 in aqueous solution and pharmaceutical fluids.

Based on density functional theory, we recently suggested that metastable α-WB2 is a promising candidate combining very high hardness with high toughness. These calculations further suggested that the addition of Tantalum supports the crystallization of α-structured W1−xTaxB2−z, with only minor reduction in toughness. Thus, various Ta containing WB2-based coatings have been synthesized using physical vapor deposition. With increasing Ta content, the hardness increases from ~41 GPa (WB2) to ~45 GPa (W0.74Ta0.26B2). In situ micromechanical cantilever bending tests exhibit fracture toughness KIC values of 3.7 to 3.0 MPa√m for increasing Ta content (single-phased up to 26 at.% Ta).

A specialized dealloying technique called thermal dealloying was developed over 10 years ago for certain biomedical materials. This method is not widely used for synthesizing nanoporous metals. However, it offers advantages over conventional dealloying processes for fabrication of nanoporous structures, and is highly suitable for refractory metals that may be susceptible to oxidation during chemical/electrochemical dealloying and liquid metal dealloying. In this study, nanoporous structures were successfully fabricated from magnesium-based precursor alloys via sublimation of magnesium at elevated temperature under vacuum conditions. Different refractory metal diffusion rates affect the resulting density and amount of retained magnesium in each nanoporous material.

In this study, we investigated the elastic constants, moduli, hardness, and electronic structures of Ti–Al intermetallic compounds (TiAl, Ti3Al, and TiAl3) using first-principles calculations. The cohesive energy and formation enthalpy of these compounds are negative, which indicates that they are thermodynamically stable. We calculated the elastic constants and moduli using the stress–strain method and Voigt–Reuss–Hill approximation, respectively. We evaluated the mechanical anisotropy of these compounds using the anisotropic index and found that the results are in good agreement with other experimental and theoretical data. We evaluated the chemical bonding of these compounds by calculating their density of states, the results of which revealed that the bonding behavior of all Ti–Al intermetallic compounds involved a mixture of metallic and covalent bonds. We also estimated the Debye temperature and sound velocities of these Ti–Al intermetallic compounds.

We propose a device to secure random data in analog format, so that it is taken off the digital grid. Such action will turn off the means by which remote hackers violate security. A physical “rock” manufactured through 3D printing technology, constructed on the basis of high-grade randomness, which is packed into the comprising materials of that rock. The rock functions as an oracle, and does not allow any massive copy of its content. Thus, a major claim of this Prospective is that materials science and engineering may hold the keys to the future of cryptography.

Transport properties, performance, and durability of a proton exchange fuel cell (PEMFC) highly depend on microstructure and spatial distribution of components in the gas diffusion layer (GDL), microporous layer (MPL), and catalyst layers (CLs) of the fuel cell. Modeling of transport properties and understanding of these effects are challenging due to limited understanding of actual three-dimensional (3D) structure of the components, especially over a wide range of length scales. In this work, 3D imaging on multiple scales, namely electron tomography on a nanoscale, focused ion beam–scanning electron microscopy on a microscale, and 3D X-ray microscopy on a macroscale, was applied to obtain 3D reconstructions of the actual CL, MPL, and GDL microstructure. Direct numerical simulations on 3D data sets with an upscaling approach were applied to demonstrate the capability to simulate overall electrical conductivity of the system. Details of the process, challenges, and results are described.

Nature’s optical nanomaterials are poised to form the platform for future optical devices with unprecedented functionality. The brilliant colors of many animals arise from the physical interaction of light with nanostructured, multifunctional materials. While their length scale is typically in the 100-nm range, the morphology of these structures can vary strongly. These biological nanostructures are obtained in a controlled manner, using biomaterials under ambient conditions. The formation processes nature employs use elements of both equilibrium self-assembly and far-from-equilibrium and growth processes. This renders not only the colors themselves, but also the formation processes technologically and ecologically highly relevant. Yet, for many biological nanostructured materials, little is known about the formation mechanisms—partially due to a lack of in vivo imaging methods. Here, we present the toolbox of natural multifunctional nanostructures and the current knowledge about the understanding of their far-from-equilibrium assembly processes.

Far-from-equilibrium systems are ubiquitous in nature. They are also rich in terms of diversity and complexity. Therefore, it is an intellectual challenge to be able to understand the physics of far-from-equilibrium phenomena. In this article, we revisit a standard tabletop experiment, the Rayleigh–Bénard convection, to explore some fundamental questions and present a new perspective from a first-principles point of view. We address how nonequilibrium fluctuations differ from equilibrium fluctuations, how emergence of order out of equilibrium breaks symmetries in the system, and how free energy of a system gets locally bifurcated to operate a Carnot-like engine to maintain order. The exploration and investigation of these nontrivial questions are the focus of this article.

The effect of severe warm rolling on microstructure and texture homogeneities was investigated in a lamellar (L12 + B2) AlCoCrFeNi2.1 eutectic high-entropy alloy (EHEA). The EHEA 90% warm-rolled at 400 °C showed disordering of the L12 phase and a remarkable increase in hardness. A much finer microstructure was observed on ND-RD (Normal Direction-Rolling Direction) plane as compared with that on the RD-TD (Rolling Direction-Transverse Direction) plane. The L12/Face Centered Cubic (FCC) phase developed α-fiber texture ND//〈110〉 with a particularly strong brass ({110}〈112〉) component, while the B2 phase developed the usual RD (//〈110〉) and ND (//〈111〉) fibers. Nevertheless, inhomogeneities in texture were noticed. Upon annealing at 800 °C, the ND-RD showed an ultrafine microduplex structure, while the RD-TD showed a retained lamellar structure. A rather uniform microduplex structure evolved after annealing at 1200 °C due to the accelerated kinetics of transformation at higher temperatures. The L12/FCC phase showed the retention of the α-fiber components, while the B2 phase showed stronger ND-fiber after annealing, although inhomogeneities in texture existed.

Materials can be endowed with unique properties by the integration of molecular motors. Molecular motors can have a biological origin or can be chemically synthesized and produce work from chemical energy or light. Their ability to access large internal or external reservoirs of energy enables a wide range of nonequilibrium behaviors, including the production of force, changes in shape, internal reorganization, and dynamic changes in mechanical properties—muscle tissue is one illustration of the possibilities. Current research efforts advance our experimental capabilities to create such “active matter” by using either biomolecular or synthetic motors, and also advance our theoretical understanding of these materials systems. Here, we introduce this exciting research field and highlight a few of the recent advances as well as open questions.